HighPoint SSD7103 Installation Manual
Nvme raid controller linux debian 10.4.0 installation guide
Hide thumbs
Also See for SSD7103:
- Installation manual (15 pages) ,
- Quick installation manual (9 pages) ,
- Installation manual (28 pages)
Table of Contents
Related Manuals for HighPoint SSD7103
Summary of Contents for HighPoint SSD7103
- Page 1 SSD7103 Linux Debian10.4.0 Installation Guide HighPoint NVMe RAID Controller SSD7103 Linux Debian 10.4.0 Installation Guide Version 1.0 Copyright © 2019 HighPoint Technologies, Inc. All rights reserved. Last updated on July 31, 2020...
-
Page 2: Table Of Contents
SSD7103 Linux Debian10.4.0 Installation Guide Table of Contents 1 Overview ............................1 2 Installing Linux Debian on SSD7103 controller ................ 1 Step 1 Prepare Your Hardware for Installation ................. 1 Step 2 Check System EFI Settings .................... 1 Step 3 Flash UEFI Rom to SSD7103 ..................3 Step 4 Create Array ........................ -
Page 3: Overview
SSD7103 only support EFI boot. If you have other SCSI adapters installed, you must make sure the SSD7103 controller EFI will be loaded firstly. If not, try to move it to another PCI slot. Otherwise you may be unable to boot up your system. - Page 4 SSD7103 Linux Debian10.4.0 Installation Guide And ‘Advanced->PCIe/PCI/PnP Configuration CPU Slot PCI-E OPROM’ to ‘EFI’. If the SSD7103 has been connected to the motherboard CPU1Slot2 PCI-E X16, you should set "CPU1Slot2 PCI-E X16 OPROM" to "EFI"; Disable ‘Secure Boot’, set ‘Secure Boot’ to ‘Disabled’;...
-
Page 5: Step 3 Flash Uefi Rom To Ssd7103
Set " Boot->Secure Boot->OS Type" to "Other OS". Step 3 Flash UEFI Rom to SSD7103 Unzip SSD7103 UEFI package to root dir (/) of a USB flash driver, and insert the USB flash drive to the motherboard; Booting from the UEFI USB flash and enter the UEFI environment;... -
Page 6: Step 4 Create Array
SSD7103 Linux Debian10.4.0 Installation Guide Step 4 Create Array Attach four NVMe SSD to SSD7103 Controller; Note Make sure your USB flash partition format is FAT32. Boot, in the presence of the motherboard Log screen, there will be NVMe SSD information：... -
Page 7: Step 5 Prepare The Driver Diskette
SSD7103 Linux Debian10.4.0 Installation Guide Command “exit”； For more command usages, refer to Appendix A. Step 5 Prepare the Driver Diskette Extract HighPoint_NVMe_Debian_10.4.0_x86_64_vx.x.x_xx_xx_xx.tar.gz to top(/) directory of an USB flash drive. It will look like: Step 6 Install Linux Debian a. - Page 8 SSD7103 Linux Debian10.4.0 Installation Guide Press "CTRL+X" or F10 to start the system. e. When the screen shows that" Select a language ". Press "CTRL+ALT+F2"(Install please press"ALT+F2") to switch to the shell on console 2, and the then execute following commands to copy the driver contents: ←...
- Page 9 SSD7103 Linux Debian10.4.0 Installation Guide g. When the screen shows that" Finish the installtion ", press " CTRL + ALT + F2"(install please press" ALT+F2") to the shell and type the following commands: ← Install SSD7103 driver. # sh /tmp/hptdd/postinst.sh A message will be displayed that the driver has been installed successfully.
-
Page 10: Installing Raid Management Software
SSD7103 Linux Debian10.4.0 Installation Guide k. After the installation is complete, you can perform system update operations. 3 Installing RAID Management Software HighPoint RAID Management Software is used to configure and keep track of your hard disks and RAID arrays attached to SSD7103 controller. - Page 11 SSD7103 Linux Debian10.4.0 Installation Guide 附录 A Support command: help/info/quit/exit/create/delete. Create Command Syntax Create Array Type (RAID0/RAID1/RAID10) Member Disk list (1/1,1/2|*)Capacity(100|*) Examples <<< create RAID0 <<< create RAID0 * <<< create RAID0 * * Create RAID0 array with all disks and with maximum capacity.
Need help?
Do you have a question about the SSD7103 and is the answer not in the manual?
Questions and answers