Yard Machines series 20 Operator's Manual
  1. Manuals
  2. Brands
  3. Yard Machines Manuals
  4. Lawn Mower
  5. series 20
  6. Operator's manual

Yard Machines series 20 Operator's Manual

20” rotary lawn mower
Hide thumbs

Advertisement

Table of Contents

Operator's Manual
IMPORTANT: Read safety rules and instructions carefully before operating equipment.
Warning:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 368022 Cleveland, Ohio 44136-9722.
MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722, U.S.A.
PRINTED IN U.S.A.
ECO No. 1224
20" Rotary Lawn Mower
Model Series
020
FORM NO. 770-10382.FM
(5/2000)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the series 20 and is the answer not in the manual?

Questions and answers

Mick
March 14, 2025

Where's air filter located on yardmachine 20"?

0

Related Manuals for Yard Machines series 20

Summary of Contents for Yard Machines series 20

  • Page 1 Operator’s Manual IMPORTANT: Read safety rules and instructions carefully before operating equipment. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest- covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).

  • Page 2: Table Of Contents

    Content Important Safe Operation Practices... 3 Slope Gauge... 6 Hardware Pack ... 7 Assembling Your Lawn Mower... 7 Know Your Lawn Mower ... 10 Operating Your Lawn Mower ... 10 Making Adjustments ... 11 Maintaining Your Lawn Mower... 11 Off-Season Storage ... 13 Troubleshooting ...

  • Page 3: Section 1: Important Safe Operation Practices

    SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.

  • Page 4: Slope Operation

    discharge cover, grass catcher, blade control handle or other safety protective devices in place and working. Never operate mower with damaged safety devices. Failure to do so, can result in personal injury. 14. Muffler and engine become hot and can cause a burn. Do not touch.

  • Page 5: Your Responsibility

    only, listed in this manual. “Use of parts which do not meet the original equipment specifications may lead to improper performance and compromise safety!” Mower blades are sharp and can cut. Wrap the blade or wear gloves, and use extra caution when servicing them. Keep all nuts, bolts, and screws tight to be sure the equipment is in safe working condition.

  • Page 6: Section 2: Slope Gauge

    SECTION 2: SLOPE GAUGE Use this page as a guide to determine slopes where you may not operate the lawn mower safely.

  • Page 7: Section 3: Hardware Pack

    SECTION 3: HARDWARE PACK Group 1 SECTION 4: ASSEMBLING YOUR LAWN MOWER NOTE: This operator’s manual covers various models of mowers. Follow only those instructions which pertain to your unit. To Remove Unit From Carton • Remove staples, break glue on top flaps, or cut tape at carton end and peel along top flap to open carton.
  • Page 8 • Install the hex bolts and flange nuts from group 4 of the hardware pack. Using two 1/2” wrenches, tighten securely. See Figure 2. Lower Handle Figure 2 Attaching Upper Handle • Place the upper handle in position over the lower handle keeping the blade control handle facing up.

  • Page 9: Attaching Wheels

    Figure 6 Securing Brake Cable WARNING: The cable must be routed properly to avoid contact with all sharp edges and hot surfaces. Such contacts damage the cable and render the controls inoperative. • Secure the cable to the lower left handle near the base of the unit with a cable tie from group 3 of the hardware pack.

  • Page 10: Know Your Lawn Mower

    Know Your Lawn Mower Compare the illustration in with your lawn mower to familiarize yourself with the location of various controls and adjustments. Throttle Control The mower engine is equipped with a constant speed throttle, which is set at full throttle for best performance. Blade Control Handle The blade control handle is located on the upper handle of the mower.The blade control handle must be...

  • Page 11: Section 6: Making Adjustments

    Using Your Lawn Mower WARNING: Never operate your unit without either the rear deflector or entire grass catcher assembly in place. • Make sure that lawn is clear of stones, sticks, wire, or other objects which could damage lawn mower and/or cause personal injury.

  • Page 12: Blade Care

    Wheels • The wheels require no lubrication. However, if the wheels are removed for any reason, lubricate the surface of the axle bolt and the inner surface of the wheel with light oil. Engine oil may also be used. When tipping the unit, empty the fuel tank and keep engine spark plug side up.

  • Page 13: Section 8: Off-Season Storage

    SECTION 8: OFF-SEASON STORAGE The following steps should be taken to prepare lawn mower for storage. • Clean and lubricate mower thoroughly as described in the lubrication instructions. • Refer to engine manual for correct engine storage instructions. • Coat mower’s cutting blade with chassis grease to prevent rusting.

  • Page 14: Section 10: Parts List For Model Series 020

    SECTION 10: PARTS LIST FOR MODEL SERIES 020...
  • Page 15 Model Series 020 Ref. Part No. Description 710-0654A Hex Ind. Washer Screw 3/8-16 x 1.0 782-0048 Cutting Deck: 20” 749-1077 Lower Handle 749-1076 Upper Handle 747-0976A Control Handle (Bail) 731-0872A Rear Flap 17098 Hinge Clip 710-1044 Screw 3/8-24 x 1.5” Group 8 936-0524A Blade Bell Support 753-0588...
  • Page 16 MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by MTD PRODUCTS INC (“MTD”) with respect to new merchandise purchased and used in the United States, its possessions and territories. MTD warrants this product against defects in material and workmanship for a period of one (1) year commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in...

This manual is also suitable for:

020 series

Table of Contents

Save PDF