Enjoying Surround Sound - Yamaha YSP-1000 Quick Reference Manual

Yamaha speaker user manual

Hide thumbs Also See for YSP-1000:

Owner's manual (106 pages)

Brochure (8 pages)

Service manual (92 pages)

page of 2

/ 2
Bookmarks

Continued

Carry out the AUTO SETUP procedure to adjust the settings that best match your listening environment.

from the front

This unit employs the YAMAHA IntelliBeam (YPAO) technology with the aid of the supplied optimizer microphone, allowing you to achieve highly accurate sound adjustments

that best match your listening environment. Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are no

children around in the listening room while the AUTO SETUP procedure is in progress.

Press STANDBY/ON on

STANDBY/ON

the remote control.

The power of this unit turns on.

DVD

INPUT1

AUX

If a subwoofer with adjustable volume and

crossover/high cut frequency controls is

VOLUME

connected to this unit, set the volume

between 11 and 1 o'clock as viewed on a

conventional clockface and set the

crossover/high cut frequency to the

maximum.

MIN

MAX

Subwoofer

Turn on the power of your TV.

Select the appropriate video input

on your TV.

Press MENU.

The menu screen appears on the TV.

If the menu screen does not appear, check the video pin cable (connection

5 in the diagram on the front page) is connected properly and then press

YSP followed by MENU.

CH LEVEL

CINEMA DSP

ENTER

TEST

RETURN

Press

to select "AUTO SETUP" and

then press ENTER.

The following screen appears on the TV.

CH LEVEL

CINEMA DSP

ENTER

TEST

RETURN

VOLUME

TV VOL

Check if "BEAM+SOUND OPTIMZ" is selected

and then press ENTER.

The following screen appears on the TV.

CH LEVEL

CINEMA DSP

ENTER

TEST

RETURN

Press

to select a

POWER

menu and then press

to select a parameter.

VCR

STB

INPUT2

MACRO

INSTALLING

• • •

Parallel to Wall, Angle to Wall or corner

Parallel to Wall: Select this if the unit is installed in parallel with the wall.

CROSSOVER/

Angle to Wall or corner: Select this if the unit is installed in the corner.

HIGH CUT

MOUNTING

SHELF, WALL

• • •

SHELF: Select this if the unit is mounted on the shelf.

WALL: Select this if the unit is mounted on the wall.

REFLECTING

• • •

NORMAL, HI ECHO

MIN

MAX

NORMAL: Select this if your listening room has a normal reflectivity.

HI ECHO: Select this if your listening room has highly reflective surfaces such as concrete walls.

Check the following points.

・We suggest you leave the room during the AUTO SETUP procedure. If you

want to stay in the room, be sure to keep quiet and position yourself beside

or behind this unit so that you may not obstruct the path of sound beams.

・To cancel the AUTO SETUP procedure after it is started, press RETURN.

・The AUTO SETUP procedure takes about 3 minutes.

Press ENTER to start the AUTO SETUP procedure.

The following screen appears on the TV.

CH LEVEL

CINEMA DSP

ENTER

TEST

RETURN

The setup screen automatically changes during the AUTO SETUP

procedure.

If any error occurs, the corresponding error message appears on the screen.

In this case, see "Error messages for AUTO SETUP" on page 35 in the Owner's

Manual and then follow the instructions. To start the AUTO SETUP procedure

once again, press RETURN and then carry out the procedure from step 5.

If the AUTO SETUP procedure is complete, the following screen appears on the TV.

Press ENTER.

The result is confirmed and the following screen appears on the TV.

CH LEVEL

CINEMA DSP

ENTER

TEST

RETURN

Press MENU.

The menu screen disappears from the TV.

The new settings are automatically saved

in the system memory.

Disconnect the optimizer microphone and

keep it in a safe place.

CH LEVEL

CINEMA DSP

Enjoy TV or DVD audio in surround sound.

For instructions on your TV or DVD player, refer to the owner's manual supplied with each component.

ENTER

Before carrying out the procedure below, set the volume of this unit to –40 dB. If necessary, adjust the volume level

in step 4.

TEST

RETURN

Enjoying TV in surround sound

VOLUME

TV VOL

Select the TV channel using the

remote control supplied with your TV.

Press TV on the remote

control of this unit.

This unit switches to the TV playback mode.

If you hear sound output from your TV speakers, turn down the volume level

until you cannot hear any sound.

Use the remote control supplied with your TV.

Press VOLUME +/– on the remote control to adjust

the volume level of this unit.

Press YSP and then press STEREO to check if digital signals are being input

to this unit.

This is an example of the result screen.

When digital audio signals such as 5.1-channel DVD audio signals are being input, the corresponding decoder indicator (

The result may differ depending on the

If no indicator lights up, a digital signal cannot be input for some reason. Check if the TV or DVD player is connected to this unit

settings.

with a digital connection, or if digital output is enabled on your TV or DVD player.

Press one of the beam mode buttons on the

remote control to select the desired beam mode.

Select one of the five beam modes that best matches the current input source of this

CH LEVEL

CINEMA DSP

unit.

For further information on the beam modes, see page 42 in the Owner's Manual.

ENTER

TEST

RETURN

To fine-tune the listening environment parameters manually or make advanced settings for

speaker positions, sound beams, etc., see "MANUAL SETUP" on page 68 in the Owner's Manual.