Related Manuals for bora GP4
Summary of Contents for bora GP4
- Page 1 Operating and installation instructions GP4U BORA GP4 induction cooktop with integrated cooktop extractor - recirculation GP4UUMIMEN-100 www.bora.com/service/installation-GP4U www.bora.com...
-
Page 2: Table Of Contents
4.1.3 Functions ................. 12 spare parts, accessories How the cooktop extractor works – recirculation ..12 10.1 BORA manufacturer’s warranty ........30 How the induction cooking zone works ......12 10.1.1 Warranty extension ............30 4.3.1 Suitable cookware ............12 10.2... -
Page 3: General Information
APAC Pty Ltd and BORA Lüftungstechnik GmbH – hereinafter emphasised with symbols and signal words. referred to as BORA – does not assume any liability for damage Safety and warning instructions are structured as follows: arising from disregard for or non-adherence to the documents WARNING SYMBOL AND SIGNAL WORD! ÿ... -
Page 4: Safety
Only use stove guards and covers that are is described here is classed as unintended. approved by the appliance manufacturer; BORA does not assume any liability for otherwise, there is a risk of accidents. damages caused by improper use or incorrect To choose a suitable stove guard, contact your operation. -
Page 5: Safety Instructions For Installation
This can damage the using the LS switch, fuses, automatic circuit appliances (particularly in the case of hard and breakers or contactor. sharp objects). Contact BORA Service. Never use the appliances as work or storage surfaces. WARNING! ÿ... - Page 6 Only install the device with the power disconnected from the mains with a contact disconnected. opening width of at least 3 mm (LS switch and Connect both sides of the fan to the duct automatic circuit breakers, fuses, contactor). system before commissioning. www.bora.com...
-
Page 7: Safety Instructions - Operation
Do not put hot cookware down in the area of the devices, (e.g. window contact switch, low operating panel. pressure warning device) and have them approved by a qualified expert (certified chimney Keep hot cookware away from the air inlet sweep). nozzle. www.bora.com... -
Page 8: Safety Instructions - Cleaning And Maintenance
When cleaning, ensure that no water penetrates to escape. the appliance. Use only a slightly damp cloth. Keep an eye on pans when cooking. Never spray the device with water. Water Try not to let them boil over. penetration can cause damage! www.bora.com... -
Page 9: Safety Instructions - Repairs, Servicing And Spare Parts
Do not touch exposed contacts on the electronic unit as they may contain residual charge. Work on electrical components must only be conducted by trained electrical personnel. Before any repair work, safely disconnect the appliance from the mains supply. www.bora.com... -
Page 10: Technical Data
GP4U device dimensions front view Power levels 1–2, power setting Size of exhaust opening 650 x 90 mm Recirculation filter 15,5 Maximum filter service life 150 h (1 year) Tab. 3.1 Technical data 25–45 490–510 Fig. 3.3 GP4U device dimensions side view www.bora.com... -
Page 11: Appliance Description
Automatic cut-off (timer) activated indicator light flashing Timer on ( ); no time set Timer off Timer display (1*) Set minutes for short time (egg timer) or automatic cut-off Timer on; no time set Tab. 4.1 Meaning of the displays www.bora.com... -
Page 12: Functions
Induction automatically takes into account the size of the cookware used which means that only the area in the cooking zone covered by the base of the pot is heated up. www.bora.com... -
Page 13: Installation
Make sure the delivery is complete and check it for damage. If there are any missing or damaged parts, please notify the BORA After Sales Service immediately. Do not under any circumstances install parts which are damaged. Dispose of transport packaging in the proper manner (see the “Decommissioning, disassembly and disposal”... -
Page 14: Gp4U Minimum Unit Dimensions
Decrease the height of the skirting boards or create dimensions. corresponding openings in the plinth. If applicable, move the rear wall. If necessary extend the height of the rear wall so that the unit is closed to the front. www.bora.com... -
Page 15: Creating The Worktop Cut-Out
735 ±2 The minimum distance of 50 mm from the front edge of the worktop to the worktop cut-out is a recommendation from BORA. Comply with the instructions of the worktop manufacturer. Create the worktop cut-out taking into account the specified cut-out dimensions. -
Page 16: Installing The Appliance
Check the direction of flow of the filters. This is identified by Open the cover [3] of the activated charcoal filter housing from an arrow. underneath by releasing the two outer locks [1] and the central Close and lock the [1]. activated charcoal filter housing cover lock [2]. www.bora.com... - Page 17 5 mounting brackets [5]. Fig. 5.16 2 on each side, 1 in the centre at the front Height adjustment plates Tightening torque: max. 2 Nm Insert the stainless steel grease filter [3] and the air inlet Cooktop nozzle [2]. Height adjustment plate www.bora.com...
-
Page 18: Establishing The Power Connection
1 x 32 A 4 mm the relevant connection diagram (see fig. “Connection diagram”). Tab. 5.2 For a one-phase or two-phase connection, connect the relevant Fuse protection and minimum cross-section contacts using the BKAS connector clip (included in delivery). www.bora.com... -
Page 19: Function Test
Provide the user with the accessories and operating and installation instructions, which are to be kept in a safe place. Carry out a thorough function test on the appliance. In the event of error messages, see the “Troubleshooting” chapter. www.bora.com... -
Page 20: Functions And Operation
If a cooking zone is operated with the power setting , the second cooking zone on that side can be operated on a maximum power level of If the power level is increased to more than , the power setting is deactivated. www.bora.com... -
Page 21: Timer Functions
After the last input, the set time will be displayed in the timer Press to switch the cooktop extractor on. display for a few seconds. displayed by the fan level indicator. In case of no further input, the cooktop extractor will switch off automatically after a few seconds. www.bora.com... -
Page 22: Power Levels
The cooktop extractor continues to run on power level 1 and 10 seconds of switching on and then press sensor button switches off automatically after 20 minutes. again. is displayed by all cooking zone indicators. The c hildproofing feature is activated. www.bora.com... -
Page 23: Residual Heat Indicator
Tab. 6.4 Overview of the safety shut-down Switch the cooking zone back on if you want to put the cooking zone back into operation. Cooktop extractor The cooktop extractor switches off automatically if no buttons are pressed for 120 minutes. www.bora.com... -
Page 24: Cleaning And Maintenance
Keep the cooktop clean. damp cloth, detergent or a mild window cleaning agent. Remove any dirt immediately. Soften dried on dirt using a damp cloth (do not scrape it off!). Only use cookware suitable for glass ceramic cooktops (see “Appliance description” chapter). www.bora.com... -
Page 25: Cleaning The Air Guiding Housing
After cleaning, rinse the air inlet nozzle and stainless steel grease filter well. Cleaning in the dishwasher Rinse the air inlet nozzle and stainless steel grease filter with a rinsing program at a maximum of 65°C. www.bora.com... -
Page 26: Changing The Activated Charcoal Filter
The activated charcoal filters must be replaced when the fan indicator shows (filter service display). You can obtain the activated charcoal filter BAKF from your specialist supplier or by contacting BORA via the website Fig. 7.7 Opening the central locks at www.bora.com. - Page 27 Position the new activated charcoal filter [1] in such a way that the arrow is pointing towards the back and is visible from underneath. Slide the activated charcoal filter into the housing. Push the activated charcoal filter upwards until the filter bracket [2] clicks into place. www.bora.com...
-
Page 28: Troubleshooting
The fan is defective or a duct connection has Contact the BORA Service team. become loose. Tab. 8.1 Resolving a fault In all other instances, contact BORA After Sales Service (see the “Warranty, technical service and spare parts” chapter). www.bora.com... -
Page 29: Decommissioning, Disassembly And Disposal
Never put your old appliance in domestic waste. Take the old appliance to a regional collection point for return and recycling electrical and electronic components and other materials. www.bora.com... -
Page 30: Warranty, Technical Service, Spare Parts, Accessories
You can extend the guarantee by registering at BORA dealer and is valid for 2 years. By registering on www. www.bora.com/registration. bora.com/registration the end customer has the possibility of extending the manufacturer’s warranty. - Page 31 Notes 11 Notes www.bora.com...
- Page 32 Please accept our apologies in this eventuality. An updated version can be requested from the BORA Service Team. Subject to printing errors and mistakes. © BORA Vertriebs GmbH & Co KG All rights reserved.
Need help?
Do you have a question about the GP4 and is the answer not in the manual?
Questions and answers