ITW Linx SURGEGATE M4KSU Instructions

Make sure you have the right ITW Linx product to protect your electronic equipment. ITW Linx makes protectors for virtually all
types of electronic equipment. Protectors that may look identical from the outside can be very different on the inside. It is very
Models: • M4KSU
M4KSU
Features:
• AC protection for telecom systems
• SurgeGate Plus Circuitry
• Expandable protection using SurgeGate Modules
• Four switched AC power outlets
• Diagnostic indicator lights (four)
• Eight foot power cord with right angle plug
• EMI/RFI noise filtration
• Mounting brackets included
• AVAYA approved product
M8KSU Features:
• AC protection for telecom
systems
• SurgeGate Plus Circuitry
• Expandable protection using
SurgeGate Modules
• Eight AC power outlets
• Diagnostic indicator lights
(four)
• Eight foot power cord
with right angle plug
• EMI/RFI noise filtration
• Mounting brackets included
• AVAYA approved product
CAU T I O N
• Do not install this device if there is not at least 10 meters (30 feet) or more
of wire between the electrical outlet and the electrical service panel.
• Risk of Electric Shock. Do not plug into another relocatable power tap.
• Do not use any other "power-strips".
• Do not use 2-prong adapters with this product.
IMPORTANT SAFETY POINTS
ITW Linx surge protectors and the connected equipment must be
indoors and in a dry location and in the same building. Although
your ITW Linx protector is very durable, its internal components are
not isolated from the environment. Do not install any ITW Linx
product near any heat emitting appliances such as a radiator or
heat register. Do not install this product where excessive moisture
is present; for example near a bathtub, sink, pool, basement floor,
fish tank, etc.
It is not unusual for a building to be improperly grounded. In order
to protect your equipment, ITW Linx products must be plugged into
a properly grounded 3-wire outlet. Additionally, building wiring and
grounding must conform to applicable NEC (USA) or CEC (Canada)
This Device features an internal protection that will disconnect the
surge protective component at the end of its useful life but will
maintain power to the load- now unprotected. If this situation is
undesirable for the appli- cation, follow the manufacturer's
instructions for replacing the device.
IMPORTANT SAFETY POINTS
STEP 1: MOUNTING THE SURGEGATE AC BASE UNIT (optional)
1. Install the SurgeGate protector near the connected equipment and within 7 feet of
a properly grounded 3-wire outlet. The protector should be mounted in a dry,
indoor location as close to the floor as possible. Leave room above the protector
to add additional modules for future expansion.
S
URGE
important that you use the surge protector designed for your application.
• M4L
M8COM-60
codes.
G AC P
roduct
ATE
ITW Linx offers a Lifetime Product and Connected Equipment Warranty on
all SurgeGate products. Please visit us at
for up-to-date warranty information.
• M8KSU • M8COM-60
M4L
Features:
• AC protection for telecom systems
• SurgeGate Plus Circuitry
• Expandable protection using
SurgeGate Modules
• Eight AC power outlets
• Diagnostic indicator lights (four)
• Eight foot power cord with
right angle plug
• EMI/RFI noise filtration
• Mounting brackets included
• Telephone protection for
four voice or DSL lines
• T1 protection for one T1 or LL line
• AVAYA approved product
• Protection for 1 LAN line
Module and
wall mounting
bracket
Line fault
indicator light
Ground OK
indicator light
15 amp circcuit
breaker
Wall mounting
bracket
2. If possible, mount the protector between the incoming wall phone jacks and
KSU/PBX when protecting a phone system—this will simplify wiring later.
3. The protector must be attached to a solid surface, such as 3/4" plywood. If the
protector will be mounted on sheet rock, you must provide appropriate fasteners.
I
NSTRUCTIONS
www.itwlinx.com
• M8COM-5X9
Features:
• AC protection for telecom systems
• SurgeGate Plus Circuitry
• Expandable protection using SurgeGate Modules
• Four switched AC power outlets
• Diagnostic indicator lights (four)
• Eight foot power cord with right angle plug
• EMI/RFI noise filtration
• Mounting brackets included
• LAN protection for one 10/100BASE-T Ethernet line
• RJ-45 Jacks
M8COM-5x9
Features:
• AC protection for telecom systems
• SurgeGate Plus Circuitry
• Expandable protection using
SurgeGate Modules
• Eight AC power outlets
• Diagnostic indicator lights (four)
• Eight foot power cord with right
angle plug
• EMI/RFI noise filtration
• Mounting brackets included
• Telephone protection for five
voice or DSL lines
• T1 protection for one T1 or LL line
• Ideal for Avaya Partner ACS 5x9
module
Figure 1
LINE FAULT UNSAFE VOLTAGE
GROUND OK POWER / PROTECTION OK
8' power cord with right angle plug
Common
ground
connection
for modules
4 AC Outlets
Unsafe voltage
indicator light
Power ON and
protection OK
indicator light
On/Off switch