Yamaha DTX700 Reference Manual page 12

Internal Design of the DTX700
Parameter
name
[TempoFlanger, G Chorus, 2 Modulator, SPX Cho-
rus, Symphonic, and Tremolo]
This parameter is used to set the modulation fre-
quency.
[TempoPhaser]
LFOSpeed
This parameter is used to set the modulation
speed in terms of note lengths.
[AutoPan]
This parameter is used to set the auto-pan fre-
quency.
[AutoWah]
This parameter is used to specify whether the filter-
sweep effect is produced using a sine or square
LFOWave
wave.
[AutoPan]
This parameter is used to set the panning curve.
This parameter is used to set the way in which
Livenss
early reflections decay.
This parameter is used to set the amount of time
LowAtk that elapses before compression is fully applied in
the low-frequency band.
This parameter is used to set the output level of the
LowGain
low-frequency band.
This parameter is used to set the low-frequency
LowLvl
level.
This parameter is used to activate and deactivate
LowMute
low-frequency muting.
[MltBndComp]
This parameter is used to set the compression
ratio for the low-frequency band.
LowRat
[Reverb effects]
This parameter is used to adjust the low-frequency
component.
This parameter is used to set the input-signal level
LowTh at which the compressor starts to process the
sound in the low-frequency band.
This parameter is used to set the low-pass filter's
LPF
cutoff frequency.
This parameter is used to set the center frequency
M.Freq
of the mid-frequency EQ band.
This parameter is used to set the amount by which
M.Gain
the mid-frequency EQ band is boosted or cut.
This parameter is used to set the width of the mid-
M.Width
frequency EQ band.
This parameter is used to set the phase-modula-
Manual
tion offset value.
This parameter is used to set the left-right inclina-
MicAngl tion of the microphone used to capture the
speaker's output.
This parameter is used to set the amount of time that
MidAtk elapses before compression is fully applied in the
mid-frequency band.
This parameter is used to set the output level of the
MidGain
mid-frequency band.
This parameter is used to set the mid-frequency
MidLvl
level.
This parameter is used to activate and deactivate
MidMute
mid-frequency muting.
This parameter is used to set the compression
MidRat
ratio for the mid-frequency band.
DTX700 Reference Manual
Descriptions
Parameter
name
This parameter is used to set the input-signal level
MidTh at which the compressor starts to process the
sound in the mid-frequency band.
This parameter is used to set how much of the
MixLvl
effect sound is mixed back into the dry sound.
This parameter is used to adjust the mode of oper-
Mode
ation of the phaser.
This parameter is used to specify the amount of
MoveSpeed time that elapses until the sound set using the
Vowel parameter is produced.
This parameter is used to activate and deactivate
On/Off
the isolator.
OutLvl This parameter is used to set the output level.
This parameter is used to set the first-stage output
OutLvl1
level.
This parameter is used to set the second-stage
OutLvl2
output level.
Output This parameter is used to set the output level.
This parameter is used to adjust the way in which
OverDr
the sound distorts.
This parameter is used to set the first stereo-pan-
Pan1
ning position.
This parameter is used to set the second stereo-
Pan2
panning position.
PanDirectn This parameter is used to set the auto-pan type.
This parameter is used to set the phase-modula-
PhShiftOfst
tion offset value.
This parameter is used to set the first pitch in semi-
Pitch1
tone units.
This parameter is used to set the second pitch in
Pitch2
semi-tone units.
This parameter is used to set the depth of pitch
PMDepth
modulation.
Often seen on guitar amplifiers and the like, this
Presenc parameter is used to control the high-frequency
band.
This parameter is used to set the compression
Ratio
ratio.
This parameter is used to set the amount of time
Release that elapses until the sound is no longer being
compressed.
This parameter is used to set the resonance of the
Resonance
filter.
This parameter is used to set the resonance offset
ResoOfst
value.
This parameter is used to set the interval between
RevDly
early reflections and subsequent reverberation.
RevTime This parameter is used to set the reverb time.
RoomSize This parameter is used to set the size of the room.
This parameter is used to set the relative volumes
Rotor/Horn of the high-frequency horn and the low-frequency
rotor.
This parameter is used to set the speed of rotation
RotorF
of the low-frequency rotor at the "fast" setting.
This parameter is used to set the speed of rotation
RotorS
of the low-frequency rotor at the "slow" setting.
This parameter is used to set how sensitive the
Sens
wah filter is to changes in the input level.
12
Descriptions