Advertisement
Solid-State Counter/Timer
1/16 DIN, Easy-to-Operate
Combination Counter and Timer
Operation selectable as preset
counter or timer
6-digit LCD display —
Present Value: 8 mm (.32 in)
Set Value: 4 mm (.16 in)
Nonsignificant zeros suppressible
from preset or count value display
Selectable power supply voltages 24
to 240 V AC and 12 to 120 V DC
Memory protection
4 programmable output modes
available for both counter and timer
functions
Ordering Information
COUNTER/TIMER
Mounting style
Operating function
Operating system (mode)
Backup power supply for memory protection
Number of counts
Timing ranges
External connection
Display type
Count and reset input for counter function;
reset and gate input for timer function
Control output
Power supply/
Power supply/
AC
counting speed
counting speed
DC
* Do not use the contact input at a counting speed of 1 kcps.
ACCESSORIES
Description
Sockets
Panel mounting adapter
Mounting track
Surface/flush mounting
Preset counter/timer (selectable)
Counter: reversible (Three input modes and four operating modes are selectable)
Timer: time-limit operation, integrating operation (Four operating modes are
selectable.)
Provided: Approx. 10 years at 20°C (68°F)
0 to 999999 (6 digits)
0.00 to 9999.99 s, 0.0 to 99999.9 min, 0.0 to 99999.9 h (6 digits)
Socket
6-digit backlit LCD; 8mm (0.32 in) Present Value, 4mm (0.16 in) Set Value
No-voltage input *
(solid-state/contact input)
Contact
30 cps
H8CA-SAL
1 kcps
H8CA-SAH
30 cps
H8CA-SDL
1 kcps
H8CA-SDH
Bottom surface or track mounting, top screw terminals
Back mounting, for use with Y92F-30 mounting adapter, bottom screw terminals
Fits behind panel, ideal for side by side installation (Use P3GA-11 socket)
DIN rail, 50 cm (1.64 ft) length
DIN rail, 1 m (3.28 ft) length
End plate
Spacer
Voltage input
Solid-state
Contact
H8CA-SALS
H8CA-SALV
H8CA-SAHS
H8CA-SAHV
H8CA-SDLS
H8CA-SDLV
H8CA-SDHS
H8CA-SDHV
H8CA-S
Solid-state
H8CA-SALVS
H8CA-SAHVS
H8CA-SDLVS
H8CA-SDHVS
Part number
P2CF-11
P3GA-11
Y92F-30
PFP-50N
PFP-100N
PFP-M
PFP-S
Advertisement
Table of Contents
Related Manuals for Omron H8CA-S Series
Summary of Contents for Omron H8CA-S Series
- Page 1 Solid-State Counter/Timer H8CA-S 1/16 DIN, Easy-to-Operate Combination Counter and Timer Operation selectable as preset counter or timer 6-digit LCD display — Present Value: 8 mm (.32 in) Set Value: 4 mm (.16 in) Nonsignificant zeros suppressible from preset or count value display Selectable power supply voltages 24 to 240 V AC and 12 to 120 V DC Memory protection...
-
Page 2: Specifications
H8CA-S H8CA-S Specifications RATINGS Supply voltage 24 to 240 VAC, 50/60 Hz 12 to 120 VDC (20% max. permissible ripple) Operating voltage range 90 to 110% of rated voltage Power consumption* Approx. 2.2 VA (at 240 VAC, 50 Hz) Approx. 1 W (at 120 VDC) Max. -
Page 3: Engineering Data
H8CA-S H8CA-S Engineering Data ELECTRICAL SERVICE LIFE Resistive Load Inductive Load 1000 1000 30 VDC (p.f. = 1) 30 VDC (L/R = 7 ms) 250 VAC (p.f. = 1) 250 VAC (p.f. = 0.4) Load current (A) Load current (A) Timing Charts IN COUNTER FUNCTION MODE IN TIMER FUNCTION MODE... - Page 4 H8CA-S H8CA-S FUNCTIONS OF INPUT SIGNALS Input type Counter output Signal high Signal low No-voltage Contact The contact turns ON The contact turns OFF Solid-state The open collector transistor is in the ON state The transistor is in the OFF state Voltage Both Input signal voltage level is 5 to 30 V...
- Page 5 H8CA-S H8CA-S Dimensions Unit: mm (inch) H8CA-S COUNTER/TIMER Panel cutout (0.03) (1.97) 13.6 63.7 45 (1.77) (0.54) (0.24) (2.51) (1.77) (1.89) (1.97) (0.31) (1.89) (3.07) Note: Recommended panel thickness is 1 to 3.2 mm. Panel cutout conforms to DIN 43700. SOCKETS 11-Pin Sockets P2CF-11 Bottom Surface or Track Mounting Socket...
-
Page 6: Selecting Function Mode
H8CA-S H8CA-S MOUNTING TRACK AND ACCESSORIES PFP-100N/PFP-50N DIN Rail PFP-M End Plate PFP-S Spacer (.24) (.07) 44.3 (1.74) (.18) 27±0.15 35.3 35±0.3 (.63) 16.5 37.3 (1.97) (1.47) 34.8 (.98) (.59) (.98) (.59) (1.37) 11.5 1000 (.39) (.39) 7.3±0.13 [500] (.39) (.39) Nomenclature Key function:... -
Page 7: Setting Example
H8CA-S H8CA-S 2. Press the key to select counter or timer function, input mode, and output mode. The characters below will flash when the is pressed. (For the counter (Select the (Select counter function, select output mode.) or timer function) the input mode.) COUNTS hours... - Page 8 H8CA-S H8CA-S Press the key until input mode “N” begins blinking. 2. Selecting the timer function with “sec” and output mode “N”. (Terminals 1 and 3 connected.) If set for timer, “sec” will begin blinking when the key is pressed. (Press the keys until the desired place is reached.) Blinking Blinking Disconnect terminals 1 and 3 before setting values.
-
Page 9: Terminal Arrangements
H8CA-S H8CA-S Connections TERMINAL ARRANGEMENTS POWER SUPPLY CONNECTION Connect power supply across terminals 2 and 10 and apply one of the specified voltages. (Pay special attention to the polarity when using a DC-operated model.) 12 to 120 VDC 24 to 240 VAC (50/60 Hz) Power Supply Cautions... - Page 10 H8CA-S H8CA-S CONNECTION OF LOAD CIRCUIT CONTROL OUTPUT Voltage input type Contact output type Reset input contact (Resets the unit when turned ON.) 30 VDC max. Load Power supply for load (250 VAC max.) (–) Note: The load is turned on when the set count or time is up. E (30 VDC max.)* Solid-state output type Reset input NPN...
-
Page 11: Power Failure Detection
H8CA-S H8CA-S CONNECTION OF COUNT INPUTS (Continued) Voltage Input type 30 VDC max. Input 1 30 VDC max. (A count Input 2 signal is Input 2 Input 1 input when turned ON.) (A count signal is input when turned ON.) (–) (–) E (30 VDC max.)*... -
Page 12: Surface Mounting
H8CA-S properly, as lithium batteries are likely to explode if incinerated. NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches, divide by 25.4. Omron Europe B.V. EMA-ISD, tel:+31 23 5681390, fax:+31 23 5681397, http://www.eu.omron.com/ema Cat. No. GC CN4A 6/98/26M Specifications subject to change without notice.
Need help?
Do you have a question about the H8CA-S Series and is the answer not in the manual?
Questions and answers