Related Manuals for Midea NA64H3010AK
Summary of Contents for Midea NA64H3010AK
- Page 1 Service Manual For Built-in gas hob GAS RANGES Refer to the service manual in the Global Service Partner Network (GSPN). See rear cover for more information...
-
Page 2: Table Of Contents
Contents Table of contents 1. Precaution…………………………………………………3 2. Description of the appliance………………………………4 2.1 Features…………………………………………….4 2.2 Components and parts……………………………...7 3. Installation…………………………………………………8 4. Disassembly & Reassembly………………………………..10 5. Troubleshooting……………………………………………18 5.1Troubleshooting……………………………………...18 5.2Problems and Corrective Measures………………….19 6. Electric Diagram……………………………………………22 7. Gas Conversition……………………………………………23... -
Page 3: Precaution
1. Precaution ‘ Safty Precautions 1. Do not modify this appliance. 2. This appliance should be serviced by an authorized person. 3. All repairs should be done in accordance with the procedures described in this manual. 4. Before you begin, turn off the gas and electricity supply to the appliance. 5. -
Page 4: Description Of The Appliance
2.Description of the appliance 2.1Features NA64H3010AK NA64H3000AK (60G40ME080-GFN-R05) (60G40ME080-GFN) 1.top plate 2.rapid burner 3.semi-rapid burner 4.auxiliary burner 5.control knob for lower left burner 6.control knob for upper left burner 7.control knob for upper right burner 8.control knob for lower right burner 9.pan support upper left (cast iron) - Page 5 2.Description of the appliance 2.1Features Q 502 GFE 1．top plate 2．rapid burner 3．semi-rapid burner 4．auxiliary burner 5．control knob for lower left burner 6．control knob for upper left burner 7．control knob for middle burner 8．control knob for upper right burner 9．control knob for lower burner 10．pan support lower left 11．pan support lower right 12．pan support upper right...
- Page 6 2.Description of the appliance 2.1Features Q411 SFD 1．top plate 2．control knob for left burner 3．control knob for upper burner 4．control knob for right burner 5．control knob for lower burner 6．auxiliary burner 7．Semi-rapid burner 8．rapid burner 9．Pan support right 10．pan support middle 11．pan support left...
-
Page 7: Components And Parts
2.Description of the appliance 2.2 Components and parts... -
Page 8: Installation
3.Installation This appliance is to be built into a kitchen unit or 600mm worktop,providing the following minimum distances are allowed; – The edge of the appliance must be a minimum distance of 55mm from a rear wall. – A minimum distance of 150mm must be left between the side edges of the appliance and any adjacent cabinets or walls. - Page 9 3.Installation –This panel (a) must be positioned at a maximum distance of 150mm below the worktop. Gas pipe or connector shouldn't be bent or blocked by any other appliances – You must conduct a gas leakage test after installation over gas connection and gas pipe.
-
Page 10: Disassembly & Reassembly
4.Disassembly and Reassembly... - Page 11 4.Disassembly and Reassembly 4-3 Disassembly and Reassembly Remove Parts on the top plate a. Remove parts on the top plate.→(Triple Crown Burner.), Inner lid(④),outer lid(③),Flame spreader(②),Control handles(⑤) b. Remove parts on the top plate. →(R,S-R,A BURNER) , Burner lids(①), Flame spreaders(②), Control handles(⑤) c.
- Page 12 4.Disassembly and Reassembly Detachment of the top plate a. Separate the top plate.(In case of stainless steel model, take off the sponge.) b. During assembly, be careful in order not to give physical impact on parts such as ignition devices, flame supervision devises..
- Page 13 4.Disassembly and Reassembly Disassemble of the ignition Electrode a. Pull the washer and take off ignition electrode b. Pull the housing of Ignition electrode out of the igniter. c. When reassembling, replace parts correctly. Right front (Semi-rapid) : 600mm Right rear (Rapid) : 600mm Left rear (Rapid , triplle crown) : 400mm Left front (Auxiliary) : 250mm...
- Page 14 4.Disassembly and Reassembly Disassemble of the Tubes a. Pull the tube after unscrewing nuts at both ends of the tube. Disassemble of the Burner Cup a. Remove 2 screws and detach the burner cup from the base box burner. Triple crown burner , 3 screw R ,S-R , A BURNER , 2 screw ...
- Page 15 4.Disassembly and Reassembly Disassemble of the igniter a. Remove 2 screws and detach the igniter from the base box burner Disassemble of the Valve & the M/F Pipe Ass’y a. Remove 5 screws b. Remove the screw to take off pipe assy. c.
- Page 16 4.Disassembly and Reassembly Disassemble of the Gas Connection a. When you disassemble/assemble gas connection, use 2 spanners. One for fixing gas connection elbow, the other for tightening gas hose. b. Tighten enough to prevent gas leakage. c. Once you’re done, conduct leakage test ...
- Page 17 4.Disassembly and Reassembly Disassemble of the appliance a. Separate casing on sink. b. Detach the appliance as checking the status of the gas connection and the power cord ass’y set. Check Point after A/S a. At completion of the appliance repair, assemble after removing tools inside of the appliance.
-
Page 18: Troubleshooting
5.Troubleshooting 5-1Troubleshooting... -
Page 19: Problems And Corrective Measures
5.Troubleshooting 5-2 Problems and Corrective Measures... - Page 20 5.Troubleshooting 5-2 Problems and Corrective Measures...
- Page 21 5.Troubleshooting 5-2 Problems and Corrective Measures...
-
Page 22: Electric Diagram
6.Electric Diagram... -
Page 23: Gas Conversition
7.Gas Conversion All work must be carried out by a qualified technician, Before you begin, turn off the gas and electricity supply to the appliance. 7-1Change the injector of the burners. Remove the pan support. Burner lid and Flame spreader.(A) Unscrew the injector using a 7mm box spanner and replace it with the stipulated injector for the new gas supply.
Need help?
Do you have a question about the NA64H3010AK and is the answer not in the manual?
Questions and answers