sisel ENDA ATC9311 Manual

Technical Specifications
ENVIRONMENTAL CONDITIONS
Ambient/storage temperature 0 ... +50°C/-25... +70°C
Max. relative humidity 80% Relative humidity for temperatures up to 31°C, decreasing linearly to 50% at 40°C.
According to EN 60529
Rated pollution degree
Height Max. 2000m
Do not use the device in locations subject to corrosive and flammable gases.
ELECTRICAL CHARACTERISTICS
Supply 230V AC +10% -20%, 50/60Hz or 24V AC 10%, 50/60Hz or optional
9-30V DC / 7-24V AC 10% SMPS module.
Power consumption Max. 5VA
Wiring
2.5mm² screw-terminal connection.
Scale 0 ... 400°C
Sensitivity 1°C
Accuracy For adjustment 4%, for display 0,5% (of full scale) or 1 digit.
Display 3 digits, 7.6mm, 7 segment red LED
Data retention
EEPROM (at least 10 years)
EMC EN 61326-1: 2013
Safety requirements EN 61010-1: 2010 (Pollution degree 2, overvoltage category II)
OUTPUT
Control output
Relay : 250V AC, 8A (for resistive load), NO+NC or 12V DC 20mA logic output
Life expectancy for relay Mechanical 30.000.000 operation; electrical 300.000 operation
CONTROL
Control type Single-setpoint control
Control algorithm On-Off / time proportional (optional)
A/D converter
10 bits
Proportional band 2% (for time proportional control)
Control period 10 second (for time proportional control)
Hysteresis 4°C (for On-Off control)
HOUSING
Housing type Suitable for flush-panel mounting.
Dimensions
W96xH96xD50mm
Weight Approx. 250g (after packing)
Self extinguishing plastics
Enclosure material
While cleaning the device, solvents (thinner, gasoline, acid etc.) or corrosive materials must not be used.
Dimensions
Depth
14mm
OUT SET
200
150 250 °C
1
100 300
50 350
0 400
ENDA ATC9311
Rubber
99mm
packing
Panel
For removing mounting clamps : Push out the flush-mounting clamp in direction 1 as shown in the figure above. Then, pull out the clamp
in direction 2. If there is no 60mm free space at back side of the device, it would be difficult to remove it
from the panel.
Front panel : IP60
Rear panel : IP20
±
±
± ± ±
Panel cut-out
105mm
50mm
90.5mm
Flush
mounting
adaptor
2
57mm
Read this document carefully before using this device. The guarantee will be expired
by damaging of the device if you don't attend to the directions in the user manual. Also
we don't accept any compensations for personal injury, material damage or capital
disadvantages.
ANALOG THERMOSTAT with DIGITAL DISPLAY
Thank you for choosing ENDA ATC9311
Control output state LED
(Light is on when control output is energized)
Applications
Plastic injection presses, automatic bread making ovens, nylon bag machines, shrink
packing machines, furniture presses, industrial ovens, textile machines, ironing
presses and other temperature control applications.
Note: Panel thickness
should be
max. 10mm.
1/2
ENDA ATC9311
OUT
200
150 250
100
50
0
ENDA
* 96 x 96mm sized.
*
Digital display for measured temperature and set value.
*
Selectable On-Off or time proportional control.
*
Fe-Const thermocouple or NiCr-Ni thermocouple input.
* Output relay is de-energized in the case of sensor failure.
*
Easy setting procedure.
*
CE marked according to European Norms.
SİSEL MÜHENDİSLİK ELEKTRONİK SAN. VE TİC. A.Ş.
Şerifali Mah. Barbaros Cad. No:18 Y.Dudullu 34775
ÜMRANİYE/İSTANBUL-TURKEY
Tel : +90 216 499 46 64 Pbx. Fax : +90 216 365 74 01
url : www.enda.com.tr
Set key
SET
Temperature display
°C
300
Temperature setting
350
knob
400
ATC9311
ENDA
ATC9311-EN-07-170814
TM