Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Heatmiser Slimline Series
Summary of Contents for Heatmiser Slimline Series
- Page 1 Model: Slimline-E V3...
-
Page 2: Product Image
Model: Slimline-E V3 Slimline Series... -
Page 3: Table Of Contents
Table of Contents Product Image Adjusting the Optional Features Table of Contents Optional Features - Table What is a Programmable Re-calibrating Room Thermostat? the Thermostat Installation Procedure Error Codes Mode Select/Factory Reset Mode 2 - Time Clock Mode 1 - Thermostat LCD Display 28-29 9-10... -
Page 4: What Is A Programmable Room Thermostat
The way to set and use your programmable room thermostat is to nd the lowest temperature settings that you are comfortable with at the di erent times you have chosen, and then leave it alone to do its job. Slimline Series... - Page 5 The best way to do this is to set the room thermostat to a low temperature – say 18°C , and then turn it up by 1°C each day until you are comfortable with the temperature. You won’t have to adjust the thermostat further. Any adjustment above this setting will waste energy and cost you more money.
-
Page 6: Installation Procedure
Do not push hard on the LCD screen as this may cause irreparable damage. This Slimline Series thermostat is designed to be ush mounted and requires a back box of 35mm (minimum depth) to be sunk into the wall prior to installation. - Page 7 Model: Slimline-E V3...
-
Page 8: Mode Select/Factory Reset
Tap the Up/Down keys to select the desired mode ..........Mode 01 = Programmable Thermostat Mode 02 = Time Clock • Press A to con rm settings ....................• Tap the ‘Power’ button to turn the display on .............. Slimline Series... -
Page 9: Mode 1 - Thermostat
Mode 1 - Thermostat Model: Slimline-E V3... - Page 10 9 10 Slimline Series...
-
Page 11: Lcd Display
LCD Display Room/Floor Temp - Indicates the current temperature sensor mode. Day Indicator - Displays the current day. Frost Icon - Displayed when the thermostat is in frost protection mode. Flame Icon - Displayed when the thermostat is calling for heat, the ame icon will ash when the optimum start function is in operation. -
Page 12: Setting The Clock
Use the Up/Down keys to set the day of the week ......... • Press A to con rm settings and return to main display ......... Minutes Hours Note: When ‘Feature 11’ is set to ‘Manual Mode’ the clock button does not respond. Slimline Series... -
Page 13: Temperature Display
Temperature Display This thermostat can be setup to use an air sensor, oor sensor or both. The display will clearly show which sensor is being controlled by showing either: Room Temperature Floor Temperature Note: Built in air sensor only MUST NOT be used to control electric under oor heating. Floor sensor only or built in air &... -
Page 14: Comfort Levels
To program comfort levels, press Clock once .............. For Weekday/Weekend programming, For 7 Day programming, Mon Tue Wed Thu Fri only Mon is displayed are displayed on screen. in the day indicator eld. For 24 hour programming, all days are displayed. Slimline Series... - Page 15 • Use the Up/Down keys to enter the required WAKE time ...... • Press H to con rm settings ..................• Use the Up/Down keys to enter the required WAKE temperature ..• Press H to con rm settings ..................•...
-
Page 16: Locking The Thermostat
You will see the lock symbol appear on screen ..........• To unlock, repeat the steps above until the lock symbol disappears. Note: The keypad lock indicator is only displayed when the lock is active. Keypad Lock Indicator Slimline Series... -
Page 17: Temperature Control
Temperature Control The Up/Down keys allow you to adjust the set temperature ....... When you press either key, you will see the word SET and the desired temperature will be displayed on screen. Use the Up/Down keys to adjust the SET value ..........Press A to con rm settings and return to main display .......... -
Page 18: Temperature Hold
You will see the ‘Hold For’ indication is displayed on screen. The time will countdown the set duration and then revert to the normal program. Hold For Indicator Hold Time Remaining To cancel temperature hold, follow the same steps but reduce the Hold time to 00:00 hours. Slimline Series... -
Page 19: Holiday
Holiday The holiday function reduces the set temperature in your home to the frost protection temperature setting (see page 19). The thermostat will maintain this temperature for the duration of the holiday and will then automatically return to the program mode on your return. •... -
Page 20: Frost Protection
Frost Protection Mode Enabled Frost set temperature range is from 7 to 17ºC (12ºC factory default) Note: If the display is turned o , the frost symbol will appear to represent heat demand in place of the ame symbol. Slimline Series... -
Page 21: Heating On/O
Heating On/O The heating is indicated ON when the ame icon is displayed. When the ame icon is absent, there is no requirement for heating to achieve the set temperature but the thermostat remains active. To turn the thermostat OFF completely, press and hold the Power button ..The display and heating output will be turned OFF completely.* To turn the thermostat back ON, press the Power button once again .... -
Page 22: Option Features Explained
Note: Built in air sensor only MUST NOT be used to control electric under oor heating. Floor sensor only or built in air & oor sensor together must be used. Slimline Series... - Page 23 Feature 07 – Floor Temp Limit: When the Floor Sensor has been enabled in feature 06, you can set a oor limiting temperature between 20-45°C, this protects the oor from overheating. (27°C is the default). Feature 08 – Optimum Start: Optimum start will delay the start up of the heating system to the latest possible moment to avoid unnecessary heating and ensure the building is warm at the programmed time.
-
Page 24: Adjusting The Optional Features
Use the Clock key to cycle through the features ............• Use the Up/Down keys to change the setting ........... • Press A to con rm settings ....................• Press the Power button once again to turn the thermostat back ON ....Slimline Series... -
Page 25: Optional Features - Table
Optional Features - Table Thermostat FEATURE DESCRIPTION SETTING 00 = °C, 01 = oF (°C = Default) Temperature Format 01° - 03°C (01°C = Default) Switching Di erential 00 = Enabled, 01 = Disabled (00 = Default) Frost Mode 00 - 15 Minutes (00 = Default) Output Delay 00°... -
Page 26: Re-Calibrating The Thermostat
• Use the Up/Down keys to con gure the new temperature ......• Press A to con rm settings ....................• Press the Power button once to turn the thermostat back ON ......Calibration Temperature Setting Set Icon Slimline Series... -
Page 27: Error Codes
Error Codes E0 = The internal sensor has developed a fault. You should contact your thermostat retailer for assistance. E1 = The remote oor probe has not been connected, has been wired incorrectly or the probe is faulty. E2 = The remote air probe has not been connected, has been wired incorrectly or the probe is faulty. -
Page 28: Mode 2 - Time Clock
The time clock can be used to control various devices in and around your home e.g. ‘Hot Water’ , ‘Towel Rails’ or even ‘Lighting’ . Refer to the manufacturers instructions for wiring to these devices. Note: Time Clock mode must not be used to control electric under oor heating. Slimline Series... - Page 29 Model: Slimline-E V3...
-
Page 30: Lcd Display
Keypad Lock Indicator - Displayed when the keypad is locked. Timer Status – Displays the current status of the timed output. Clock - Digital clock display in 24h format. Hold For - Displayed when a timer override is active, the remaining time will be shown. Slimline Series... -
Page 31: Setting The Clock
Setting the Clock To set the clock, follow these steps. • In Countdown mode, press the Clock button once ............. • In either 5/2, 7-day, or 24h mode, press the Clock button twice ......• Use the Up/Down buttons to set the hours ............•... -
Page 32: Locking The Time Clock
• You will see the lock symbol appear on screen ............• To unlock, repeat the steps above until the lock symbol disappears. Note: The keypad lock indicator is only displayed when the lock is active. Keypad Lock Indicator Slimline Series... -
Page 33: Setting The Switching Times
Setting the Switching Times To program the switching times, follow these steps. • Press the Clock button once ....................• You will see Mon (7 day mode), Mon - Fri (5/2 day mode) or Mon -Sun (24H mode) displayed on screen. Use the Up/Down buttons to select the TIMER ON for the WAKE switching period .................. -
Page 34: Countdown Mode
• Hold For will appear showing the time left. When Hold For is displayed on screen, the output will be active. Hold For Icon Hold Time Remaining Timer Status To cancel a countdown period, reduce time to 00:00. Slimline Series... -
Page 35: Timer Override
Timer Override The time clock is able to override its current timer status. If current status =Timer ON, – pressing A will switch it to Timer OFF ....... (TIMER OFF will ash to inform you the programmed output has been overridden) The time clock will return to the program at the next programmed time. -
Page 36: Holiday
Saturday will be counted as the rst day and the time clock will revert back to the ON Indicator programmed schedule at 00:00 on Monday. To cancel, follow the same steps but reduce the holiday duration to 00 days. Slimline Series... -
Page 37: Optional Features Explained
Optional Features Explained THE FOLLOWING SETTINGS ARE OPTIONAL AND IN MOST CASES NEED NOT BE ADJUSTED Feature 01 – Programming Mode: The following program modes are available; 5/2 Day Programming – 4 levels for the weekdays and 4 di erent levels for the weekend. 7 Day Programming –... -
Page 38: Optional Features - Table
• Use the Clock key to cycle through the features ............• Use the Up/Down keys to change the setting ............• Press A to con rm settings ...................... • Press the Power button once again to turn the time clock back ON ....... Slimline Series... -
Page 39: Wiring Diagrams
Wiring Diagram - Slimline-E Slimline-E MAINS SUPPLY 230VAC Floor Remote Sensor Air Sensor LOAD FLOOR PROBE MATTING OR WIRE REMOTE AIR PROBE (Optional) Model: Slimline-E V3... - Page 40 Notes ........................................................................................................................................................................................................................................................................................................................................................................................................................................................Model: Manual REF Slimline Series...
- Page 41 Notes ........................................................................................................................................................................................................................................................................................................................................................................................................................................................Model: Slimline-E V3...
- Page 42 Call our support team on: +44 (0)1254 669090 Or view technical speci cations directly on our website: www.heatmiser.com VIDEO Twitter: @heatmiseruk Facebook: facebook.com/thermostats Rev.1.1 Heatmiser UK Ltd, Units 1-5 Hurstwood Court, Mercer Way Shadsworth Business Park, Blackburn, Lancashire, BB1 2QU, United Kingdom.
Need help?
Do you have a question about the Slimline Series and is the answer not in the manual?
Questions and answers