PE micro CYCLONE Getting Started Manual
  1. Manuals
  2. Brands
  3. PE micro Manuals
  4. Motherboard
  5. Cyclone MAX
  6. Getting started manual

PE micro CYCLONE Getting Started Manual

Hide thumbs Also See for CYCLONE:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
CYCLONE & CYCLONE FX PROGRAMMERS
This guide will allow the user to program their device with a Cyclone programmer, using a simple programming
image, by completing the following steps.
•
•
•
•
This guide is intended as a supplement to the Cyclone's User Manual, which contains in-depth information
about the topics covered here and much more.
1

Installing The Cyclone Software

First, the Cyclone software should be installed on the user's PC. It can be downloaded from the Support &
Downloads tab on the pemicro.com product page for CYCLONE or CYCLONE FX, or directly from https://
www.pemicro.com/downloads/download_file.cfm?download_id=481.
Once the software is downloaded, the user should install it on their PC. If Cyclone software is already installed
on the PC, it is recommended that the old installation be removed before the user installs the latest software.
Note: The User Manual for CYCLONE or CYCLONE FX programmers, which contains more detailed information
about the topics covered here, is installed along with the Cyclone software. It can also be downloaded from
the Support & Downloads tab.
2

Setting Up The Cyclone Hardware

Step 1. Configure Cyclone power settings
The Cyclone has several different power configurations. The label on the bottom of the Cyclone indicates the
appropriate Jumper settings for each. The user should install the Jumpers as indicated for their desired power
configuration.
The Jumpers are located underneath the Cyclone's access panel. They are labeled "Power Jumpers." and
numbered from 1-4. The Cyclone_ACP is shown in the example below; the jumper location will be similar for all
Cyclone models.
©
2019 P&E Microcomputer Systems, Inc., all rights reserved.
Getting Started Guide
Installing the Cyclone software
Setting up the Cyclone hardware
Creating a stand-alone programming image
Launching Cyclone programming
v.1.00
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CYCLONE and is the answer not in the manual?

Questions and answers

Related Manuals for PE micro CYCLONE

Summary of Contents for PE micro CYCLONE

  • Page 1 Installing The Cyclone Software First, the Cyclone software should be installed on the user’s PC. It can be downloaded from the Support & Downloads tab on the pemicro.com product page for CYCLONE or CYCLONE FX, or directly from https:// www.pemicro.com/downloads/download_file.cfm?download_id=481.
  • Page 2 Step 2. Connect Cyclone to a PC (for programming image setup) The Cyclone programmer should be connected to the PC via USB, Serial, or Ethernet. Cables for each of these options are included with the Cyclone. Note: An Ethernet connection requires IP setup on the Cyclone unit; please refer to the Cyclone’s User Manual for more information.
  • Page 3 These are combined into a single encrypted file. This SAP image can then be loaded onto the Cyclone and used to program, without need for the Cyclone to be connected to a PC.
  • Page 4 Step 1. Run Cyclone Image Creation Utility CreateImage.exe is in the “ImageCreation” folder, in the location where the Cyclone software was installed. For an in-depth description of the Cyclone Image Creation Utility please refer to the User Manual for your Cyclone programmer.
  • Page 5 Based on the algorithm that was selected, additional commands will be made available in the box of programming commands on the left. The user should then double-click on the SS command to specify the Object Code. Cyclone Programmer - Getting Started Guide...
  • Page 6 As an example, some basic commands might be • Erase • Program • Verify Note: Launch Script Wizard can also be used to quickly complete Steps 3 and 4. Step 5. Other Settings Cyclone Programmer - Getting Started Guide...
  • Page 7 Step 6. Save SAP image to Cyclone The user should then save the SAP image onto the Cyclone by clicking the button to save to “Cyclone Only” or “Cyclone & Disk.” The image will be automatically selected as the current SAP image on the Cyclone.
  • Page 8 2. Cyclone Control Console (command-line utility) - The user writes a script that specifies parame- ters and initiates programming using the command line. More information is available in the Cyclone’s User manual or at: http://www.pemicro.com/blog/index.cfm?post_id=142 3. SDK - The SDK is a software library that is used in conjunction with the user’s own code. The user writes a customer application that uses this library of functions to launch programming.

This manual is also suitable for:

Cyclone fxCyclone universal fxCyclone universalCyclone acpCyclone acp fx

Table of Contents