Table of Contents
Advertisement
Quick Links
101-732 – NanoStation Loco M5 – P2P Setup Guide
Introduction
This tech note will show you how to setup the 101-732 as a Point to Point network.
This mode will be ideal for connecting an intercom door station at one access point and
then the room station at the other access point, or even a CCTV camera at one access point
and the NVR at the other access point.
Notes
You won't be able to scan / see the access point using a Smartphone or computer once it
has been setup. This is a secure hidden network.
Hardware Required
Computer with a working hardwired LAN connection
•
2 x 101-732 NanoStation Loco M5
•
LAN Cable
•
Quick Setup Guide
In this quick setup guide we are going to refer the units as Nano A and Nano B.
Page 1
Advertisement
Table of Contents
Related Manuals for Ness NanoStation Loco M5
Summary of Contents for Ness NanoStation Loco M5
- Page 1 101-732 – NanoStation Loco M5 – P2P Setup Guide Introduction This tech note will show you how to setup the 101-732 as a Point to Point network. This mode will be ideal for connecting an intercom door station at one access point and then the room station at the other access point, or even a CCTV camera at one access point and the NVR at the other access point.
- Page 2 Setting Up Nano A 1. Connect your computer to the LAN port on the PoE and the NanoStation to the PoE port and connect the PoE Adaptor to the wall socket. 2. Change your computer’s IP address so it has a static IP address of 192.168.1.5 from the network and sharing center on your computer so it looks similar to the following: Page 2...
- Page 3 3. Open a web browser on your computer and navigate to http://192.168.1.20 When prompt to do so, enter the username and password to login. Default login is: Username: ubnt Password: ubnt 4. Once logged in click on the ‘Wireless’ tab. 5.
- Page 4 7. It’s recommend to run the ‘AirView’ tool to select the best wireless channel. 8. Set the frequency based on your results from step 7. 9. Set the security type to be WPA2-AES with the WPA Authertication to be PSK. 10.
- Page 5 13. Set the network mode to be ‘Bridge’. 14. Set a Static IP address for this NanoStation like below: 15. Click on the ‘Change’ button down the bottom of the page to save the values. 16. Once you click on ‘Change’ button, click on the first tab and long the top. (no need to click Apply just yet) 17.
- Page 6 18. Click the Apply button to save the settings to the NanoStation. Leave this unit powered up. Leave this unit powered up once it has been configured. Page 6...
- Page 7 Setting Up Nano B 1. Connect your computer to the LAN port on the PoE and the NanoStation to the PoE port and connect the PoE Adaptor to the wall socket. 2. Open a web browser on your computer and navigate to http://192.168.1.20 When prompt to do so, enter the username and password to login.
- Page 8 6. Select the Nano A that we just setup from the list and click on ‘Lock to AP’ 7. Enter in the wireless security settings that you used for Nano A. 8. Click on the ‘Change’ button down the bottom of the page to save the values. 9.
- Page 9 If you still can’t ping both devices then you have a confiuration issue and recommand you default both units and run through this quick guide again. Additional Information: Customer Service 1300 551 991 (M-F 8:30am – 5:00pm) Phone: customerservice@ness.com.au Email: www.youtube.com/nesscorporation YouTube: Tech Note ID: 01160928AK Revision:...
Need help?
Do you have a question about the NanoStation Loco M5 and is the answer not in the manual?
Questions and answers