ENDA ATC9311 Quick Manual

Technical Specifications
ENVIRONMENTAL CONDITIONS
Ambient/storage temperature
0 ... +50°C/-25... +70°C
80 % up to 31°C decreasing linearly 50
Max. relative humidity
According to EN 60529
Rated pollution degree
Height
Max. 2000m
Do not use the device in locations subject to corrosive and flammable gases.
ELECTRICAL CHARACTERISTICS
230V AC +10% -20%, 50/60Hz or 24V AC 10%, 50/60Hz or optional
Supply
9-30V DC / 7-24V AC 10% SMPS module. ±
Power consumption Max. 5VA
Wiring 2.5mm² screw-terminal connection.
Scale 0 ... 400°C
Sensitivity
1°C
Accuracy For adjustment 4%, for display 0,5% (of full scale) or 1 digit. ±
Display
3 digits, 7.6mm, 7 segment red LED
Data retention
EEPROM (at least 10 years)
EMC
EN 61326-1: 1997, A1: 1998, A2: 2001 ( For EMC tests performance criterion B is satisfied.)
Safety requirements
EN 61010-1: 2001 (Pollution degree 2, overvoltage category II)
OUTPUT
Control output
Relay : 250V AC, 2A (for resistive load), NO+NC or 12V DC 20mA logic output
Life expectancy for relay Mechanical 30.000.000 operation; electrical 300.000 operation
CONTROL
Control type Single-setpoint control
Control algorithm
On-Off / time proportional (optional)
A/D converter 9 bits
Proportional band 2% (for time proportional control)
Control period 10 second (for time proportional control)
Hysteresis 4°C (for On-Off control)
HOUSING
Housing type
Suitable for flush-panel mounting.
Dimensions
W96xH96xD50mm
Approx. 250g (after packing)
Weight
Self extinguishing plastics
Enclosure material
While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.
Dimensions
Depth
14mm
SET
OUT
200
150 250 °C
1
100 300
50 350
0 400
ENDA
ATC9311
Rubber
99mm
packing
Panel
For removing mounting clamps: Push out the flush-mounting clamp in direction 1 as shown in the figure above. Then, pull out the clamp in
direction 2. If there is no 60mm free space at back side of the device, it would be difficult to remove it from
the panel.
% at 40°C.
Front panel : IP60
Rear panel : IP20
±
± ±
Panel cut-out
105mm
50mm
90.5mm
Flush
mounting
adaptor
2
57mm
Read this document carefully before using this device. The guarantee will be
expired by damaging of the device if you don't attend to the directions in the user
manual. Also we don't accept any compensations for personal injury, material
damage or capital disadvantages.
ANALOG THERMOSTAT with DIGITAL DISPLAY
Thank you for choosing ENDA ATC9311 temperature controller.
Control output state LED
(Light is on when control output is energized)
Application areas
Plastic injection presses, automatic bread making ovens, nylon bag machines,
Note: Panel thickness
should be
shrink packing machines, furniture presses, industrial ovens, textile machines,
max. 10mm.
ironing presses and other temperature control applications.
1/2
ENDA ATC9311
OUT
200
150 250
100
50
0 400
ENDA
ATC9311
* 96 x 96mm sized.
* Digital display for measured temperature and set value.
* Selectable On-Off or time proportional control.
* Fe-Const thermocouple input.
* Output relay is de-energized in the case of sensor failure.
* Easy setting procedure.
* CE marked according to European Norms.
Set key
SET
Temperature display
°C
300
Temperature setting
350
knob
ATC9311-E-05-R