10. Technical data angular travel) 1. INTRODUCTION The J4 io actuator is designed to drive the external venetian blind, types 1 & 2. What is io-homecontrol®? The J4 io uses io-homecontrol®, the new universal and secure wireless communication protocol, shared by the major manufacturers in the world of home automation.
- The motor, torque and operating time must be adjusted according to the complete installation. - Only Somfy original accessories should be used (adapters, brackets, connectors, power cable, etc.). - Correct operation of the installation is only guaranteed if the installation and assembly have been carried out according to best practices, if the electrical supply is adequate and if maintenance is carried out.
Screw the 2 adaptors (1) using 2 M3x8 bolts (2) on the motor shaft. Tightening torque = 1,35 N.m +/- 20% Ensure that the J4 io plate cable does not pass over a rotating part of the motor or mechanism. If necessary, compress the edge of the head rail (4) into the motor zone.
Screw the 2 adaptors (1) using 2 M3x8 bolts (2) on the motor shaft. Tightening torque = 1,35 N.m +/- 20% Ensure that the J4 io plate cable does not pass over a rotating part of the motor or mechanism. Insert the motor into the head rail (4).
Screw the 2 adaptors (1) using 2 M3 x 8 bolts (2) on the motor shaft. Tightening torque = 1,35 N.m +/- 20% Ensure that the J4 io plate cable does not pass over a rotating part of the motor or mechanism. Fit the two head rail adaptors (8) on the motor.
Page 9
Screw the 2 adaptors (1) using 2 M3 x 8 bolts (2) on the motor shaft. Tightening torque = 1,35 N.m +/- 20% Ensure that the J4 io plate cable does not pass over a rotating part of the motor or mechanism. Fit the two head rail adaptors (8) on the motor.
Page 11
Mounting inside the head rail Mounting outside the head rail The mounting of the J4 io plate inside the head rail is compatible with the following head rails and shafts: HEAD RAIL SHAFT 57 x 51 mm Up to 14 mm hex...
Earth (Yellow/Green) 6. COMMISSIONING The guide only describes commissioning using a Situo mobile io VB type Somfy io local control point which provides greater precision when tilting the slats. For commissioning using any other io control point, refer to the corresponding guide.
6.4. Basic settings 5.4.1. Setting upper and lower end limits Check that your J4 io actuator has been assembled in the blind in the lowered position with the slats closed. Press the Up button for 3 seconds. The blind rotates in the up direction.
A long press on the Up or Down buttons will cause the blind to raise or lower completely. 7.2. Operating with a Somfy sensor or automatic function Refer to the corresponding manual for the Somfy io sensor. 8. MODIFICATION OF THE SETTINGS 7.1. Favourite position (my) 7.1.1.
8.2. Adding/Deleting Somfy io control points and io sensors Refer to the corresponding guide. 8.3. Modifying the end limits 8.3.1. Modifying the upper end limit Place the blind in the intermediate position. Press the Up and Down buttons for 5 seconds the blind...
8.4. Modifying the angular travel For optimum operation of the J4 io actuator, it is The angular travel is the total angle necessary for the blind to change from a slats closed position to a slats fully open position. The slats fully open position is reached when the slats no longer tilt and the blind makes an initial raising movement.
Page 19
Readjust the angular travel and then reset The angular travel is incorrectly set. cannot be repeated. the "my" favourite position. No solution by adjusting the J4 io. Recall the ladders. «my» position from the lower end limit. The blind (or one of...
9.3. Replacing a component of the actuator If necessary it is possible to physically replace the J4 io motor, the J4 io plate, or both. In all circumstances, in order to have an operational installation, the following procedure must be carried...
For the J418, the maximum permissible torque for an end of the motor shaft is 12 Nm. Thermal time J4 io motors are protected by a thermal cut-out in case of overheating caused by continuous use for longer than 6 minutes.
Need help?
Do you have a question about the J4 io and is the answer not in the manual?
Questions and answers