1. Manuals
  2. Brands
  3. Harper Manuals
  4. Farm Equipment
  5. Deweze Super Slicer
  6. Operator's & parts manual

Harper Deweze Super Slicer Operator's & Parts Manual

Super slicer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SUPER SLICER
OPERATOR'S & PARTS
MANUAL
Super Slicer
1-2019

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Deweze Super Slicer and is the answer not in the manual?

Questions and answers

Related Manuals for Harper Deweze Super Slicer

Summary of Contents for Harper Deweze Super Slicer

  • Page 1 SUPER SLICER OPERATOR’S & PARTS MANUAL Super Slicer 1-2019...
  • Page 2 Super Slicer...

  • Page 3: To The Owner Or Operator

    Toll Free 800-835-1042 Email info@deweze.com Website www.deweze.com © 2019 Harper Industries, Inc. The Harper and DewEze names are registered trademarks of Harper Industries, Inc. All other brand and productnames are trade- marks or registered trademarks of their respective companies. Super Slicer...

  • Page 4: Warranty Statement

    Statement of Warranty Harper Industries warrants to each purchaser of a new DewEze Super Slicer from an au- thorized dealer or representative, that such equipment is free of manufacturer’s defects which appear while in normal service for a period of ONE YEAR commencing with deliver to the original user.

  • Page 5: Table Of Contents

    Table of Contents OPERATOR SECTION To the Owner or Operator..........Warranty Statement............Table of Contents............Specifications..............Safety Guidelines............Set-Up Instructions............Operation Hydraulic Requirements........Loading Instructions.......... Feeding Instructions......... Adjustments Feed Rate............Flow Control Valve Adjustments....... Sickle Drive Adjustments........Maintenance Schedule............ PARTS SECTION Complete Table Assemly........

  • Page 6: Specifications

    81” Sickle Bar - 27 individual sickle sections (knives) NOTE: Following publication of this manual, certain changes in standard equipment and options may have occurred which would not be included in these pages. Your Harper dealer is the best source for up-to-date information. Super Slicer...

  • Page 7: Safety Guidelines

    Hydraulics Safety Guidelines To prevent serious injury or death: • Relieve pressure on system before repairing, adjusting or disconnecting • Use genuine factory parts or parts any hydraulic hose or fitting. with equivalent characteristics, includ- • Wear proper hand and eye protection ing type, strength and material.

  • Page 8: Set-Up Instructions

    Set-Up Instructions SAFETY WARNING! OPERATING THE SUPER SLICER LIFT- ING ARM WITH THE TABLE IN THE ROAD/ Your SUPER SLICER is shipped from TRANSPORT POSITION WILL DO DAMAGE the factory in a “knockeddown” position to TO THE LIFT ARM LINKAGE! make it easier to transport.

  • Page 9: Operation

    HYDRAULIC REQUIREMENTS system, as the system will be at Your new DEWEZE SUPER SLICER is de- maximum flow and pressure. (Load is signed to be used as a mobile feeding unit sensed at the tractor selective control...

  • Page 10: Loading Instructions

    LOADING INSTRUCTIONS Adjustments (Trailer Mounted Unit Only) Approach the bale on its right side with the SAFETY WARNING! lift arm lowered to the ground. If your trac- Excessive sickle speed may cause table vi- tor is equipped with dual rear wheels, you bration and damage to the hydraulic motor may have to reposition the tongue to allow and/or the sickle!

  • Page 11: Flow Control Valve Adjustments

    NOTE: The backboard will slide up or down FLOW CONTROL VALVE ADJUSTMENT in relation to the sideboards without loosen- ing any other bolts. The flow control valve on the right controls the speed of the sickle; the valves loosen the Retighten the four 5/8”...
  • Page 12 Loosen 4 bolts (1) on Bell Crank (2). (See Fig. 6). Position the Bell Crank so that the Bell Crank arm connected to the sickle head (3) is perpendicu- lar to the Pitman rod (4). Use a square as shown to set the center line of the arm perpendicular.

  • Page 13: Maintenance Schedule

    Maintenance TRAILER MAINTENANCE MONTHLY (Or every 100 bales) Grease the linkage of the lift arm to avoid binding and rust. ANNUALLY Clean and repack the wheel bearings. TABLE MAINTENANCE MONTHLY (Or every 100 bales) Grease the Pitman drive bearings, one grease fitting per bearing. Grease knuckle joints on Pitman arm (two fittings) Check the conveyor chain for tightness.
  • Page 14 Super Slicer...

  • Page 15: Parts Section

    PARTS SECTION Super Slicer...
  • Page 16 Super Slicer...

  • Page 17: Complete Table Assemly

    Table of Contents PARTS SECTION Complete Table Assemly........Table Assembly..........Trailer Assembly..........Sickle Drive Assembly........Sickle Bar Assembly......... Bellcrank Assembly........... Pitman Assembly..........Sideboards & Shields........Decals............... Hydraulic Assembly - PTO Option....PTO Kit............. Table Drive Hydraulics Option......Table Drive Hyd. Schematic......Super Slicer...
  • Page 18 Super Slicer...
  • Page 19 Super Slicer...
  • Page 20 Super Slicer...
  • Page 21 Super Slicer ii 1.2...
  • Page 22 Super Slicer...
  • Page 23 Super Slicer...
  • Page 24 Super Slicer...
  • Page 25 Super Slicer ii 1.4...
  • Page 26 Super Slicer...
  • Page 27 Super Slicer...
  • Page 28 Super Slicer...
  • Page 29 Super Slicer...
  • Page 30 Super Slicer...
  • Page 31 Super Slicer...
  • Page 32 Super Slicer...
  • Page 33 Super Slicer...
  • Page 34 Super Slicer...
  • Page 35 Super Slicer...
  • Page 36 NOTES Harper Industries, Inc. Telephone: 620-896-7381 151 E. Highway 160 Toll-Free: 800-835-1042 Harper, KS 67058 Fax: 620-896-7129 Website: www.harperindustries.com E-mail: info@harperindustries.com Super Slicer...

Table of Contents