Gemini 933 Series Installation And Use Manual
  1. Manuals
  2. Brands
  3. Gemini Manuals
  4. Security System
  5. 933 Series
  6. Installation and use manual

Gemini 933 Series Installation And Use Manual

Hide thumbs Also See for 933 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
INSTALLATION CERTIFICATE
The undersigned qualified installer attests having personally fitted the here described vehicle
security system following the manufacturer instructions.
By :
Sold on :
................................................
V
ehicle
:
..........................................................................................................................
GEMINI Technologies S.r.l.
Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italia
Tel. +39 0332 943211 - Fax +39 0332 948080
www.gemini-alarm.com
ISO 9001 Certified Company
933
T
ype of product
:
932
SERIE 933
INSTALLATION AND
USE MANUAL
Made in Italy
933
932
UK
AC 2784 Rev. 06 - 05/16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 933 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Gemini 933 Series

Summary of Contents for Gemini 933 Series

  • Page 1 ..........ehicle .......................... INSTALLATION AND USE MANUAL GEMINI Technologies S.r.l. Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italia Tel. +39 0332 943211 - Fax +39 0332 948080 www.gemini-alarm.com AC 2784 Rev. 06 - 05/16 Made in Italy...

  • Page 2: Table Of Contents

    PAGE 03 electrical connections etc. will therefore apply to all models. USER MANUAL Before installing, identify your alarm model and refer to it for the correct instructions GEMINI 932: same as 933 without self-powered battery. - OPERATING DESCRIPTION..................PAGE 03 The following signs, intended for the installer or the user, indicate particular functions or connections 2.1 - Complete system arming..................

  • Page 3: System Armed

    5“. The guarantee is valid exclusively at authorized Gemini Technologies S.p.A. Service Centers. An alarm event generates a maximum of ten 30” alarm cycles for each input and for each arming cycle The manufacturer declines any responsibility for eventual malfunctions of the device or any damage to the vehicle electrical system due to improper installation, use or tampering.

  • Page 4: Installer Manual

    INSTALLER MANUAL 6.0 - WIRING DIAGRAM 5.0 - PINOUT TABLES Before carrying out electrical connections, 5.1 - 20-PIN CONNECTOR disconnect the negative battery terminal and re- POSITION WIRE FUNCTION WIRE COLOUR connect again after Connection - 1 - ----- ----- completion.

  • Page 5: Connection For Turn Signals Activation

    The various arming modes are listed below and the connections indicated in the following paragraphs. ORANGE Arming via CAN BUS line. GEMINI 933 ORANGE Arming via door lock motor unit SYSTEM WHITE-ORANGE Arming via turn indicators flashes...

  • Page 6: Vehicle Code Programming

    SHORT PAUSE are updated at packaging time). Up-to-date information on supported vehicle models can be found in the private area of our website: www.gemini-alarm.com 3 FLASHES The system has an indicator LED that signals any wrong vehicle code inserted. The code must range between 100 and 235 otherwise the LED on the unit blinks Press the vehicle remote control lock/unlock buttons to make sure the alarm system works repeatedly and the procedure is interrupted.

  • Page 7: Optical Signals

    Negative output during alarm cycle Disabled With the alarm system disarmed, turn ignition key “ON” and touch the electronic For Gemini use only: Turn ignition key ----- key to its receptacle. *ATTENTION: Starting from Rev.13 (indicated on barcode label), the function ‘...
  • Page 8 13.0 - ADDING NEW DEVICES 14.0 - DELETING PROGRAMMED DEVICES To carry out the operation successfully, make sure the required electrical connections To carry out the operation successfully, make sure the required electrical connections (bonnet switch and ignition) are complete. (bonnet switch and ignition) are complete.
  • Page 9 15.0 - ULTRASONIC VOLUMETRIC PROTECTION 17.0 - TECHNICAL SPECIFICATIONS 15.1 - CO NNECTION AND POSITIONING Power supply 12 Vdc nsert the WHITE connector in the “W” marked socket and the RED connector in the “R” marked Current absorption @ 12Vdc with system armed and LED flashing 15 mA socket (see figure below).

This manual is also suitable for:

932

Table of Contents