Advertisement
Brewer Features
Strong Brew increases the strength and bold taste of your
coffee's flavor. For bolder coffee, press the STRONG button and
select your brew size.
Iced Coffee: Brew hot over ice and enjoy cold. Makes full-
flavored and delicious iced coffee.
Hot Water on demand for instant soups and oatmeal.
Smart Start heats then brews in one simple process. No need to
wait for the brewer to heat before selecting brew size. Power on
your brewer, add coffee, then select your brew size. The brewer
will heat, then automatically begin brewing.
Clock allows you to set an Auto On time.
Programming Brewer Features
To program your K-Elite
brewer, use the settings button
®
up and down arrows . After the feature is programmed, press
the settings button until you return to the home clock screen.
Clock: Press the settings button once and use the up and down
arrows to select the correct hour. Press the settings button
again and use the up and down arrows to select the correct
minutes.
Temperature Control: Press the settings button 3 times and use
the up and down arrows to select your preferred temperature.
Auto On: Press the settings button until a sun icon
Then use the up and down arrows to turn the Auto On
functionality "on." Press the settings button again to set your
preferred time, using the up and down arrows. Once you return
to the home clock screen a sun icon will be present to let you
know that the functionality is on.
NOTE: You must set the clock to enable to Auto On functionality.
Temperature Control allows you to adjust the temperature
from 187° – 192°.
Auto On sets your brewer to turn on at a specific time.
Auto Off automatically turns your brewer off 2 hours after the
last brew for energy savings. You can also program your brewer
to shut off in 15 minute increments after your last brew, or
remain on all the time.
High Altitude ensures your brewer works properly at higher
altitudes (5,000 feet).
NOTE: In High Altitude mode the temperature is not adjustable. If you attempt to adjust
the temperature, the mountain icon will flash indicating that you are in high altitude mode.
Auto Off: Press the settings button and use the up and down
and
arrows to set your preferred off time. Off time can be set
from 15 minutes to 2 hours in 15 minute increments. A moon
icon
will appear on the screen to indicate your brewer is in
Auto Off mode.
To disable Auto Off, use the up and down arrows to turn the
functionality "off." The moon icon will no longer appear on
the screen.
To enable Auto Off, use the up and down arrows to turn the
functionality "on." The moon icon will appear on the screen.
High Altitude: Press the settings button until you see the
appears.
mountain icon
turn this setting on or off.
NOTE: In high altitude mode the temperature is not adjustable. If you attempt to adjust the
temperature, the mountain icon will flash indicating you are in high altitude mode.
displayed on your screen. Use the arrows to
Advertisement
Need help?
Do you have a question about the K-Elite and is the answer not in the manual?
Questions and answers
How you replace or change the "my k-cup" on the keurig k-elite?
Can the coffee **** stay on? Do I have to push the power button and wait each time?
The Keurig K-Elite coffee maker has an Auto On functionality, but the clock must be set for it to work. If this feature is not enabled, the power button will need to be pushed each time to turn it on.
This answer is automatically generated
there is nothing about the filter do i have t change it or remove it when i descale the machine
Yes, you need to remove the water filter before descaling the Keurig K-Elite. The manual states that if using a Keurig Water Filter, you should remove and set it aside before starting the descaling process.
This answer is automatically generated
how do I clear the red descale light?
To clear the red descale light on a Keurig K-Elite, follow these steps:
1. Prepare for Descaling:
- Remove any used K-Cup® pod from the machine.
- Empty and wash the water reservoir with mild soap and warm water.
- Refill it with fresh filtered water.
2. Descale the Brewer:
- Use Keurig Descaling Solution or white vinegar.
- Pour the solution into the water reservoir.
- Run several brew cycles without inserting a K-Cup® pod until the "Add Water" light turns on.
3. Rinse the Brewer:
- Refill the reservoir with fresh water.
- Run multiple water-only brew cycles to remove any remaining descaling solution.
4. Clean Needles (If Needed):
- Remove the pod holder and clean the exit needle with a straightened paper clip.
- Clean the entrance needle on the lid using the same method.
5. Final Steps:
- Reassemble all cleaned parts.
- The descale light should turn off after completing the process.
Descale your brewer every 3-6 months to prevent buildup and keep it functioning properly.
This answer is automatically generated
how to install the filter in the water reservoir?
To install the filter in the water reservoir of the Keurig K-Elite:
1. Get the Correct Filter – Use the long-handle water filter for the K-Elite, as the reservoir is taller.
2. Prepare the Carbon Filter – Soak the carbon filter in water to remove dust or debris.
3. Insert the Filter into the Holder – Place the prepared carbon filter inside the filter holder.
4. Attach the Filter Holder – Snap the long-handle filter holder onto the black piece inside the reservoir.
5. Secure the Filter in Place – Gently push down until it clicks into place.
6. Reassemble the Reservoir – Place the reservoir back onto the machine and replace the lid.
The filter should be replaced every two months.
This answer is automatically generated
When i set the automatic on button, if I put in a new pod, and close the lid, will it brew? Or is it just a heat the water program?
The Auto On function primes the Keurig K-Elite for brewing at a predetermined time, but it does not automatically start brewing when a new pod is inserted. The user still needs to initiate the brew manually.
This answer is automatically generated
am/pm? how to set?
Do you power off when done brewing.
Yes, the Keurig K-Elite has an auto-off feature that allows you to set the machine to turn off automatically after a selected time, ranging from 15 to 120 minutes after brewing.
This answer is automatically generated
K-Elite K90. Powers on, all lights flash. Press a cup selection and then machine powers off. All cup size selections make this happen. However, the 'ICED" button works and brews.