Related Manuals for Loup Electronics Elite
Summary of Contents for Loup Electronics Elite
- Page 1 DRILL & PLANTER MONITOR DRILL & PLANTER MONITOR OPERATION MANUAL SOFTWARE v4.0.5 • 2019...
-
Page 2: Table Of Contents
LOUP ELITE DRILL/PLANTER MONITOR • OPERATION MANUAL SERVICE AND TECHNICAL SUPPORT Contact: Loup Electronics Inc. Address: 3030 N. 40TH St. AFTER HOURS/WEEKEND SUPPORT: Lincoln, NE 68504 402-318-6415 Phone: 877-489-LOUP(5687) 402-464-7131 402-853-6249 Fax: 402-464-7104 E-mail: info@loupelectronics.com CONTENTS 5.0 POPULATION AND RATE SETTINGS ..10 5.1 High Alarm . -
Page 3: Overview
LOUP ELECTRONICS • 1-877-489-5687 • WWW.LOUPELECTRONICS.COM 1.0 OVERVIEW e Loup Elite Monitor is a full featured display designed to provide accurate population, blockage, bin level, sha RPM and other readings for gravity drills, air seeders and planters. is manual will familiarize you with operation, calibration and technical information. -
Page 4: Main Screen Layout
LOUP ELITE DRILL/PLANTER MONITOR • OPERATION MANUAL 1.1 MAIN SCREEN LAYOUT 1.2.6 SETTING A TARGET RATE To set your Target Rate, select the 1.2.1 POPULATION DISPLAY window for target icon in the center of the screen and from the pop-up enter e Average Seeds/Acre information will display in the center of the desired target in seeds/acre. -
Page 5: Planter Bar Graph
LOUP ELECTRONICS • 1-877-489-5687 • WWW.LOUPELECTRONICS.COM Section Average: If sections are setup on your drill, 1.2 BASIC OPERATING • this will scroll through and display each section PROCEDURE average for the sensors active on that section. Ensure the correct Implement type (gravity drill, air seeder •... -
Page 6: Tasks & Logging Procedure
“Row 4” and section 3 as “Row 6”. Each Section Width would be 10 . NOTE: If the Elite system is a newly purchased kit from Loup Electronics, all Implement Settings and Sensor Select the “Next Section” button to scroll to the next section. -
Page 7: Install/Setup Menu
Up to three separate implements can be selected on the Loup be prompted with “Manual Learn Complete”. Push “Ok” to Elite. Unless pre-con gured by Loup, all three implements will nish. default as gravity drills. To switch implements simply select the “My Saved Implements”... -
Page 8: Speed Settings
LOUP ELITE DRILL/PLANTER MONITOR • OPERATION MANUAL 4.0 SPEED SETTINGS 4.2 PULSES PER REVOLUTION Available when “Sha Speed” is selected. Located by selecting “Menu” and “Speed Pulses per Rev (Revolution) are the number Settings”, these settings control the type of magnets the implement mounted speed... -
Page 9: Implement Switch
LOUP ELECTRONICS • 1-877-489-5687 • WWW.LOUPELECTRONICS.COM Select the “Start Calibration” button 4.5.2 IMPLEMENT SWITCH to begin. BY SEEDRATE As you drive the 400 distance, pulses for both Wheel Pulses When using the “Seedrate” mode, the monitor will wait to see and/or Radar Pulses will begin accumulating on-screen. -
Page 10: Population Adjust
Typically used when planting small grains displays seed rate. e type of implement such as wheat. Contact Loup Electronics for further assistance you are using a ects the type of sensitivity you should be using. with the Population Adjustment. For drills and air seeders its recommended to use either settings “Low”... -
Page 11: Individual Runs Setup
“Auto” setting, blockage is calculated Forward O set: in accordance to the current speed. Leave this setting as “Auto” Posative (+) Number unless otherwise speci ed by Loup Electronics. Rearward O set: Negative (-) Number 6.6 RESET MODULES Right O set:... -
Page 12: Gps Status
LOUP ELITE DRILL/PLANTER MONITOR • OPERATION MANUAL 8.2 GPS STATUS 9.1 ENTERING A TASK NAME e GPS Status screen gives a diagnostics Begin a new task by rst entering report of the current Latitude, Longitude, the task name you desire. Select... -
Page 13: Stopping A Task
Diagnostics screen can help in identifying issues with sensors, harnessing or other items. Status reports for Battery Voltage, Sensors Learned, MUX Communication speed and GPS Communication speed are displayed. Contact Loup Electronics if you need technical support. 11.3 UNITS Toggles between US (feet) or Metric (meters) units. -
Page 14: System Update
Electronics for the unlock code required for this feature. default settings. 11.5.3 YIELD MONITORING UNLOCK Loup Elite can be used in both seeding and harvest applications. Contact Loup Electronics for the unlock code for unlocking the yield monitoring application. 11.5.4 FACTORY RESET Selecting this will reset all settings back to Factory Default. - Page 15 LOUP ELECTRONICS • 1-877-489-5687 • WWW.LOUPELECTRONICS.COM NOTES...
- Page 16 www.loupelectronics.com 1-877-489-5687...
Need help?
Do you have a question about the Elite and is the answer not in the manual?
Questions and answers