Safety Instructions - TROLL nursery SCANDY COTBED Quick Start Manual

* Your child's safety is your responsibility.
* The cotbed is designed to be dismantled for storage or transport.
* Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a
competent person.
* Follow assembly instructions in detail to ensure the safety features of the cotbed are not
compromised.
* Take care when handling or moving the furniture. Careless handling may cause damage.
* Toddler bed age range of child is 18 months to 4 years.
* Keep children clear during assembly as pack contains small parts which may present a
choking hazard.
* Remove all parts from packaging and check against the parts list.
* Do not discard any packaging until you are sure you have all parts and the pack of fittings.
* You will find it easier to assemble the cot
* WARNING : Be aware of the risk of open fires and other sources of strongheat, such as
electric bar fires, gas fires etc in the near vicinity ofthe cot
bounce, jump and climb on beds, therefore the child's bed should not be placed too close
to other furniture or windows, blind cords, curtain pulls or other strings or cords, and should
be placed either tight to any wall or have a gap of 300mm between the wall and the side of
the bed.
* WARNING : Do not use if any part of the cot
spare parts approved by the manufacturer.
* WARNING : Do not leave anything in the cot
provide a foothold or present a danger ofsuffocation or strangulation e.g. strings,
blind/curtain cords etc.
* Keep medication, string, elastic, small toys or small items, such as money, out of reach from any
position in the cot.
* WARNING : Do not use more than one mattress in the cot.
* One end of the cot has a mark indicating the
* RECOMMENDED MATTRESS SIZE: This cot has been manufactured for use with a mattress
which measures 700 mm wide by 1400 mm long and 100 mm in thickness. The width and length
are specified because it is important that the gaps between the mattress and the sides and
ends of the cot will not exceed 30 mm when the mattress is pushed to one side or end, and
15 mm when the mattress is centered in the cot. This is to minimize the risk of a child's limb
becoming caught in the gap. The thickness of the mattress has been specified to ensure that the
depth of the cot is greater than 500 mm with the mattress base in the lower position to minimize
the risk of a child climbing or falling out of the cot and minimum distance of 300 mm is maintained
between the top surface of the mattress and the top of the lowest side or end with the access
closed and the base in its upper position.
* WARNING: TO PREVENT FALLS, THE MAXIMUM MATTRESS THICKNESS SHOULD NOT
EXCEED 100 mm.
* WARNING: TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT SHOULD BE
ADJUSTED TO THE LOWEST POSITION BEFORE THE CHILD CAN SIT UP.
* All assembly fixings should always be tightened properly. Periodically check all fixings to
ensure none have come loose, and that there is no risk of clothing or parts of the body
becoming snagged or trapped.
* To prevent injury from falls, when the child is able to climb out of the cot, the cot shall no longer
be used for that child.
* Do not allow your child to jump on the bed. This may result in damage to the furniture and/or
injury to your child.
* Your furniture may be cleaned by wiping with a damp cloth and drying with a soft clean cloth.
Do not use abrasives, bleach, alcohol or ammonia-based household polishes.
Manufacturer:
SIA Troll Smiltene,
Rigas street 18, Smiltene,
LV-4729, Latvia
www.troll.lv

SAFETY INSTRUCTIONS

bed if a second adult is available to help you.
bed
or place close to another product
maximum
CUSTOMER ENQUIRIES
Australian distributor:
Danish by Design,
PO Box 1543 Black Rock VIC 3193.
www.danishbydesign.com.au
. Children are likely to play,
is broken, torn or missing
height of the mattress.
and use only
, which could