National Instruments SCC-AO10 User Manual
Isolated analog output module
Hide thumbs
Also See for SCC-AO10:
- User manual (13 pages) ,
- User manual (12 pages) ,
- Quick start manual (36 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for National Instruments SCC-AO10
Summary of Contents for National Instruments SCC-AO10
- Page 1 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
- Page 2 SCC-AO10 Isolated Analog Output Module The SCC-AO10 is an isolated voltage output module with an output range of ±10 V. The output voltage level is controlled by the DAC output of an E/M Series DAQ device. You can increase the output voltage level to ±20 V by connecting two SCC-AO10 modules in series.
-
Page 3: What You Need To Get Started
SC-2345 refers to both the SC-2345 connector block and the SC-2345 with configurable connectors. SCC refers to any SCC Series signal conditioning module. What You Need to Get Started To set up and use the SCC-AO10, you need the following items: ❑ Hardware –... -
Page 4: Device Specific Information
Plug the SCC-AO10 into either SC-2345/2350 analog output socket J(X+17), where X is 0 or 1. The SC-2345/2350 routes the voltage output of E/M Series DAQ device analog output channel AO (X) to the SCC-AO10. Connecting the SCC-AO10 to a Load... - Page 5 Figures 1 and 2 show the SCC-AO10 connected to a nonreferenced load and to a load with a high common-mode voltage. E/M Series SCC-AO10 DAQ Device AO (X ) Load AO GND Figure 1. SCC-AO10 Connected to a Nonreferenced Load...
- Page 6 Figure 3. Connecting Two SCC-AO10 Modules in Series The SC-2345/2350 routes the E/M Series DAQ device analog output channels AO 0 and AO 1 to the SCC-AO10 modules, and the resulting maximum output voltage range is ±20 V. Refer to Figure 3 and use the...
- Page 7 Calibrating Gain and Offset Errors The SCC-AO10 is calibrated at the factory before shipment. To adjust the gain and offset of the SCC-AO10 in your system using an E/M Series DAQ device, you need a voltage meter and a 1/8 in. flathead screwdriver. Before adjusting the SCC-AO10, allow 30 minutes for the DAQ device to warm up to its nominal operating temperature.
-
Page 8: Specifications
Adjust the offset potentiometer on the top of the SCC-AO10 until the voltmeter reads 0 VDC ±100 μV. The offset is now calibrated. Using your software, have AO (X) output 9.9 VDC. Adjust the gain potentiometer on the top of the SCC-AO10 until the voltmeter reads 9.9 VDC. -
Page 9: Power Requirement
Weight ............28 g (1.0 oz) I/O connectors.........One 20-pin right-angle male connector; one 3-pin screw terminal Field-wiring diameter ......28 to 16 AWG SCC-AO10 Isolated Analog Output Module User Guide ni.com Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com... -
Page 10: Maximum Working Voltage
Recommended warm-up time ....10 min (30 min for connected E/M Series DAQ device) Output offset drift........300 μV/°C Gain temperature coefficient....300 ppm/°C © National Instruments Corporation SCC-AO10 Isolated Analog Output Module User Guide Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com... -
Page 11: Electromagnetic Compatibility
DoC for this product, visit , search by model ni.com/certification number or product line, and click the appropriate link in the Certification column. SCC-AO10 Isolated Analog Output Module User Guide ni.com Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com... -
Page 12: Environmental Management
RoHS ni.com/environment/rohs_china (For information about China RoHS compliance, go to ni.com/environment/rohs_china SCC-AO10 Connector Pin Assignments Figure 5 shows the I/O connector pins on the bottom of the SCC-AO10. 1 Pin 1 Pin 2 PWB Key Pin 19 5 Pin 20 Figure 5. - Page 13 — — National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section on ni.com/legal for more information about National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies.
- Page 14 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
Need help?
Do you have a question about the SCC-AO10 and is the answer not in the manual?
Questions and answers