Related Manuals for ryan JR SODCUTTER 6HP B&S 12"
Summary of Contents for ryan JR SODCUTTER 6HP B&S 12"
- Page 1 744844F JR SODCUTTER 6HP B&S 12" 744845F JR SODCUTTER 6HP B&S 18" 744944B JR SODCUTTER 5.5HP HONDA 12" 744945B JR SODCUTTER 5.5HP HONDA 18" OPERATOR'S MANUAL 4163593...
- Page 2 CALIFORNIA Proposition 65 Warning WARNING Diesel engine exhaust and some The engine exhaust from this product of its constituents are known to the contains chemicals known to the State State of California to cause cancer, of California to cause cancer, birth birth defects and other reproductive defects or other reproductive harm.
-
Page 3: Table Of Contents
JR SODCUTTER IMPORTANT MESSAGE Thank you for purchasing this Schiller Grounds Care, Inc. product. You have purchased a world class product, one of the best designed and built anywhere. This machine comes with aN Operation and Parts Manual. The useful life and good service you receive from this machine depends to a large extent on how well you read and understand this manual. -
Page 4: Safety
SAFETY JR SODCUTTER NOTICE !!! This symbol means: ATTENTION! Unauthorized modifications may present extreme BECOME ALERT! safety hazards to operators and bystanders and could also result in product damage. Your safety and the safety of others is involved. Schiller Grounds Care, Inc. strongly warns against, rejects and disclaims any modifications, add-on Signal word definitions accessories or product alterations that are not... - Page 5 SAFETY JR SODCUTTER MAINTENANCE SAFETY Blades WARNING In general The sod cutter blade is sharp and can cut. Use extra cau- Maintain machine according to manufacturer's tion when handling. Remove schedule and instructions for maximum safety obstructions with care. Wrap and best results.
-
Page 6: Set-Up
SET-UP JR SODCUTTER SET-UP To prevent injury, wear eye protection and stand clear whe cutting banding. Banding is under tension and may snap back when cut. 1. Remove crate top, sides and plastic covering unit. Remove the banding attaching the Jr. Sodcutter to the pallet. -
Page 7: Adjustments
ADJUSTMENTS JR SODCUTTER DRIVE BELT ADJUSTMENT DRIVE BELT Keep belt free of oil and dirt, and adjusted to PULLEY ENGINE PULLEY proper tension at all times. IDLER PULLEY Belt tension is adjusted by loosening four (4) ENGINE engine mounting bolts and shifting engine on the BOLT base. - Page 8 ADJUSTMENTS Sodcutter ADJUSTING OPERATOR PRESENCE CONTROL 1. To adjust operator presence cable, pull clutch control handle A rearward as far as possible. 2. Press operator presence handle (right handlebar) down as far as possible. 3. Adjust cable until the pivot arm C contacts the arm extending from the operator presence switch 4.
-
Page 9: Maintenance/Service
MAINTENANCE Sodcutter When replacement parts are required, use genuine Schiller Grounds Care, Inc. parts or parts with equivalent characteristics, including type, strength and material. Failure to do so may result in product malfunction and possible injury to the operator and/or bystanders. Carbon monoxide present in the exhaust is an odorless and deadly gas. - Page 10 MAINTENANCE Sodcutter Lubrication: The gear case is initially filled with 3 1/2 pints (1.7 L) of EP 140 Gear Lube. Do not add to this amount unless oil is changed or lost through leakage. Gear case drain plug D. On all pressurized lubrication fittings use a good grade of Lithium Based lubricant.
- Page 11 MAINTENANCE Sodcutter DRIVE BELT REPLACEMENT 1. Remove shield on left side of unit. 2. Remove nut securing brake band to clutch control rod. 3. Remove cotter pin on outside of guard support rod and move brake band over to nut on rod. 4.
- Page 12 MAINTENANCE Sodcutter DRIVE WHEEL CHAIN SPROCKET SHAFT 1. Follow steps 1 thru 7 in drive chain removal 5. Install axle nut on end of shaft, opposite the side section. of snap ring previously removed. 2. Remove master link and remove chain from top 6.
- Page 13 MAINTENANCE Sodcutter UPPER DRIVE SPROCKET & SHAFT 1. Follow steps 1 thru 6 in drive chain removal section. 2. Remove master link from chain. Chain does not need to be removed from lower sprocket. 3. Remove drive shifter assembly from gear case. 4.
- Page 14 MAINTENANCE Sodcutter PULLEY SHAFT 1. Follow steps 1 thru 4 in belt replacement section and steps 2 thru 6 in drive chain removal section. 2. Remove blade from unit and remove left side arm. 3. Remove blade shifter assembly. 4. Turn pulley until master link is on top of sprocket. Remove chain from top sprocket.
- Page 15 MAINTENANCE Sodcutter BLADE SPROCKET SHAFT 1. Follow steps 1 thru 6 in pulley shaft section. 2. Loosen clamp screw on left pitman arm C and remove from shaft. 3. Loosen clamp screw in eccentric assembly D and remove. 4. Remove two (2) top screws securing the other side arm assembly.
-
Page 16: Storage
MAINTENANCE / STORAGE Sodcutter IDLER GEAR SHAFT 1. Remove belt guards. 2. Follow steps 2 thru 6 in drive chain removal section. 3. Remove plug from right side of unit. 4. Remove snap ring C from groove by small gear B to left end of shaft A. -
Page 17: Troubleshooting
TROUBLE SHOOTING Sodcutter Sharpen or replace blade. . f f See page 15. l l i . e l . e l . t l . f f . t u . t u e l l . l e . -
Page 18: Specifications
SPECIFICATIONS Sodcutter Models: 744844F..Jr. Sodcutter - 12 in.(30.5cm) 744845F..Jr. Sodcutter - 18 in.(45.7cm) Dimensions: Engine Width.......... 24" (600 mm) Model.....4 cycle 6.5H.P.(4.8KW) B&S Vangaurd, Length........49" (1244 mm) Model 12H332, Type 0115, Height......... 33" (838 mm) Trim B8, 12.5 cu. in. (205 cc) Wheelbase......... -
Page 19: Parts Section
PARTS SECTION JR SODCUTTER PARTS SECTION... -
Page 20: Drive Assembly And Side Cover
DRIVE ASSEMBLY AND SIDE COVER JR SOD CUTTER FIGURE 1... - Page 21 (USED ON 544845E & 544945A) 64006-05 LOCKWSHR-HELICAL 1/2 F1002 NUT, JAM 1/4-20 UNC ZP 547428.7 IDLER ARM AY 64123-67 BLT-HEX 3/8-16X2 4163976 LABEL-RYAN 64139-01 BLT-WLF 5/16-24X3/4 548480 HALF LINK 64123-50 BOLT-HEX 3/8-16X1 4117675 LINK AY, #50 CONNECT 64123-68 BOLT-HEX 5/16-18X1 524610.7...
-
Page 22: Muffler Guards
MUFFLER GUARDS JR SOD CUTTER FIGURE 2... - Page 23 MUFFLER GUARDS JR SOD CUTTER FIGURE 2 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4160486.7 GUARD-MUFFLER B&S (USED ON B&S MODELS ONLY) 64152-56 SCREW-HS STAP #12X1/2 64205-038 BLT-METRIC M6-1.00X20 64006-01 LOCKWSHR-1/4 HELICAL 4160484.7 BRKT-MUFFLER GRD VERT 1 (USED ON B&S MODELS ONLY) 64163-02 WSHR .321/.328X.608X11GA 4160485.7...
-
Page 24: Gear Case
GEAR CASE JR SOD CUTTER FIGURE 3... - Page 25 GEAR CASE JR SOD CUTTER FIGURE 3 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 64006-03 WSHR, 3/8 HELICAL LOCK 1 546037.7 COVER AY, GEAR CASE 64123-67 BLT-HEX 3/8-16X2 519404 GEAR,DRIVE 64123-80 BLT-HEX 1/4-20X1-1/4 (INCLUDES ITEMS 45-47) 64006-02 LCKWSHER-HELICAL 5/16 64164-19 KEY WOODRUFF.19X.75 #9 3 548775...
-
Page 26: Side Arms, Pitman Arms And Handles
SIDE ARMS, PITMAN ARMS AND HANDLES JR SOD CUTTER FIGURE 4... - Page 27 SIDE ARMS, PITMAN ARMS AND HANDLES JR SOD CUTTER FIGURE 4 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 64123-50 BOLT-HEX 3/8-16X1 548183 LWSHR,.31.09 HI-COLLAR 64123-68 BOLT-HEX 5/16-18X1 800198 NUT,.5-20 YS HX CRNLCK 64123-61 BLT-HEX 5/16-18X1-3/4 800513 SCRW-SCKT 5/16-18-1-1/4 328018 SCRW,.44-14 1.12 YS HX 548056 NUT,.44-14 YS HX UNITORQ 6...
-
Page 28: Handlebar Assembly
HANDLEBAR ASSEMBLY JR SOD CUTTER FIGURE 5... - Page 29 PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 111898 CLAMP,CABLE 48228A CABLE CLIP-INSULATED 64025-15 NUT-HEX #10-24 KEPS 814585 BUSHING 4161125 LABEL-RYAN 64139-06 BOLT-WLH 5/16-18X5/8 64025-04 NUT-3/8-24 HEX 64006-02 LCKWSHER-HELICAL 5/16 800896 TSCRW,.190-24.75 64197-015 BLT-TDFM 10-32X1/2 TORX 2 64163-55 WASHER .328X.75X14 GA 64006-01...
-
Page 30: Mole Blade Kit
MOLE BLADE KIT JR SOD CUTTER FIGURE 6... - Page 31 MOLE BLADE KIT JR SOD CUTTER FIGURE 6 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 544670 MOLE BLADE KIT- 3/4" (USED ON 744844F & 744944B) (INCLUDES ITEMS 14 & 16-17) 544725 MOLE BLADE KIT- 3/4" (USED ON 744845F & 744945B) (INCLUDES ITEMS 13 &...
-
Page 32: Trenching Kit
TRENCHING BLADE JR SOD CUTTER FIGURE 7... - Page 33 TRENCHING BLADE JR SOD CUTTER FIGURE 7 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 546199 BLADE KIT (INCLUDES ITEMS 2-6) * MODEL 744844F, ONLY 64006-03 WSHR, 3/8 HELICAL LOCK 3 64025-04 NUT-3/8-24 HEX 64123-21 BLT-HEX 3/8-24X1-1/4 546089 BRACKET,12"-MOLE BLADE 1 546198 BLADE AY,TRENCHING *NOTE: The trenching blade set includes...
Need help?
Do you have a question about the JR SODCUTTER 6HP B&S 12" and is the answer not in the manual?
Questions and answers