Sealey ASC50 Instructions

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
▲ Caution
spring assisted centre column.
Always place light pressure on top of the
column when releasing the locking pin.
do not stand over or point unit at others
when removing locking pin to avoid potential
Refer to
injury from spring.
instructions
Always store fully extended where possible.
1. safety
‰
WarninG!
do not overload stands beyond rated CapaCity. overloadinG Can Cause damaGe to, or failure of,
the stands. position load on Centre of CrutCh/saddle only. alWays ensure adeQuate number of stands
are used to support the load fully and use on a hard level surfaCe Capable of sustaininG the load.
use of stands on other than hard level surfaCes Can result in load instability and possible loss of
load. do not use on tarmaCadam. failure to folloW these instruCtions may result in damaGe to stands,
loss of load resultinG in property damaGe, serious personal injury or loss of life.
▲ danGer! Great Care must be taKen to ensure you loWer the vehiCle (or other load)
sloWly and Carefully onto the Centres of the CrutCh/saddle of the stands.
ensure the load does not exceed the maximum capacity as marked on the stand.
9
Always ensure adequate number of stands are used to support the load fully.
9
no alterations or modifications shall be made to this product.
9
Use on a hard, level surface, e.g. concrete. do not use on uneven ground or tarmacadam.
9
securely chock wheels in contact with the lift/ground. Before jacking and placing the stands, apply vehicle
9
handbrake.
make sure that each stand is securely located under a strong point on the vehicle; consult the vehicle
9
manufacturer's handbook for guidance. ensure that height adjust locking mechanism is fully located before
applying any load to the stand. ensure that the load is located centrally on the saddle, and that the
weight is directed through the vertical axis of the stand.
exercise extra care when using with a three wheeled vehicle or a trailer. Refer to vehicle manufacturer's
9
instructions. once vehicle is supported, ensure that the vehicle and stands are stable before starting work.
ensure that it is not possible for the vehicle to move before commencing any work.
Inspect stands before each use. do not use if they show signs of damage. do not use if it is suspected
9
that they have been overloaded.
Before commencing any work or going beneath the vehicle, undertake a risk assessment. ensure that a responsible person is aware of
9
the work about to be undertaken.
Replace any labels on the stand should they become unreadable. This applies in particular to any warning or operation instruction
9
labels. If replacement labels are required, contact your sealey stockist.
do not use stands on the highway, or anywhere else if it is deemed to be unsafe.
8
do not push or twist the vehicle/load whilst it is supported on stands.
8
do not mix components between stands. Use only as supplied.
8
do not allow children or animals in the vicinity of a vehicle supported on stands.
8
do not leave a vehicle on stands in an area that could be considered a hazard to others or property.
8
© Jack sealey limited
CommerCial vehiCle support stands
5, 7 & 12tonne CapaCity
asC50, asC70, asC120
model nos:
important note: these stands are rated singly. Used in pairs they will
support twice the rated load.
taKe Care; you may know the total weight of the vehicle you want to
support but you cannot calculate the exact weight distribution between support
points.
for this reason always allow a 40% margin for error.
for example: a vehicle weighing 20tons could have a single axle load of more
than 10tons and two 5ton supports would not be adequate.
Original Language Version AsC50, AsC70, AsC120 Issue 2 (f) 21/11/18