Table of Contents
Advertisement
Quick Links
I.
Care and Maintenance ........................................................................................ 2
II. Glazing Assembly................................................................................................ 2
III. Panel Assembly ................................................................................................... 2
1.
"X" Panel ...........................................................................................................................2
2.
"O" Panel ...........................................................................................................................4
3.
Add Yokes to Meeting Stiles .............................................................................................5
IV. Frame Assembly.................................................................................................. 5
V. Frame Opening Verification & Sillpan Installation ........................................... 6
1.
Sillpan Substitution............................................................................................................6
2.
Frame Opening Verification...............................................................................................6
3.
Pre-Fit and Leveling ..........................................................................................................6
4.
Sealant Application............................................................................................................6
VI. Frame Installation................................................................................................ 7
VII. Sill Track Installation........................................................................................... 7
VIII.Sill Track Removal .............................................................................................. 8
IX. Head Bumper Installation ................................................................................... 8
X. Panel Installation ................................................................................................. 8
XI. Screen Installation............................................................................................. 10
XII. OXO Panel Configuration ................................................................................. 11
DOC NO: Series 3000-T Installation & Assembly Instructions
SERIES 3000-T
ASSEMBLY & INSTALLATION INSTRUCTIONS
Table of Contents
Rev. C
Page 1 of 12
DATE: 03/25/19
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Fleetwood 3000-T Series
-
Page 1: Table Of Contents
SERIES 3000-T ASSEMBLY & INSTALLATION INSTRUCTIONS Table of Contents Care and Maintenance ..................2 II. Glazing Assembly....................2 III. Panel Assembly ....................2 “X” Panel ...........................2 “O” Panel ...........................4 Add Yokes to Meeting Stiles .....................5 IV. Frame Assembly....................5 V. Frame Opening Verification & Sillpan Installation ........... 6 Sillpan Substitution......................6 Frame Opening Verification....................6 Pre-Fit and Leveling ......................6... -
Page 2: Care And Maintenance
Care & Maintenance Instructions (go to www.fleetwoodusa.com for more information). Contact the local dealer with any questions or concerns. Fleetwood strongly recommends that all products be cleaned after installation and totally protected from construction debris and equipment. II. Glazing Assembly 1. - Page 3 SERIES 3000-T ASSEMBLY & INSTALLATION INSTRUCTIONS Note: Before installing lead and interlocker stiles to panels please check required orientation with customer order • Place the interlock stile; weather-strip facing up on the right side for XO, and weather-strip facing up on the left side for OX. •...
-
Page 4: O" Panel
SERIES 3000-T ASSEMBLY & INSTALLATION INSTRUCTIONS 2. “O” Panel • Center the top rail onto the glass. Using a rubber mallet, drive the rail onto the glass until the rail seats against the vinyl lip. Repeat this procedure with the bottom rail. Note: Before installing fixed and interlocker stiles to panels please check required orientation with customer order. -
Page 5: Add Yokes To Meeting Stiles
SERIES 3000-T ASSEMBLY & INSTALLATION INSTRUCTIONS 4. Add Yokes to Meeting Stiles General Rules: Latching hardware for typical installation is located in the right hand panel (facing exterior); customer has option to reverse at the time of order. Female yoke is attached to the stile containing the latch mechanism. -
Page 6: Frame Opening Verification & Sillpan Installation
SERIES 3000-T ASSEMBLY & INSTALLATION INSTRUCTIONS V. Frame Opening Verification & Sillpan Installation 1. Sillpan Substitution • If the factory provided sillpan is not desired, the product warranty will remain intact if the substitute panning system emulates the essential design of the factory pan. This sliding door has passed specific air, water, energy and structural testing with the factory provided sillpan. -
Page 7: Frame Installation
Attach frame to structure as shown below (Figures 15 & 16). Note: Size and location of fasteners to be per local code. Blocking, stainless steel screws (recommended), and wall finish not furnished by Fleetwood. Frame installation anchors furnished by installer. Figure 15: Figure 16:... -
Page 8: Viii.sill Track Removal
SERIES 3000-T ASSEMBLY & INSTALLATION INSTRUCTIONS VIII. Sill Track Removal 1. Using a pair of pliers, slightly squeeze the track together at one end and pull up. 2. Using a screwdriver, slowly pry the track out of the sill. Although you can re-insert the track, we recommend replacing with a new track for optimal performance of the door. - Page 9 SERIES 3000-T ASSEMBLY & INSTALLATION INSTRUCTIONS “O” Panel Installation 1. Add 2” long sill block and secure with #8 x 3/4” long pan head self taping screw to the bottom of sill as shown in Figure 24. 2. Insert panel into the upper head channel.
-
Page 10: Screen Installation
SERIES 3000-T ASSEMBLY & INSTALLATION INSTRUCTIONS XI. Screen Installation • Insert screen into the upper head channel. Push up and swing the bottom inward until screen is vertical, then lower screen down onto the track. HEAD OUTSIDE OUTSIDE PANEL OUTSIDE THRESHOLD Figure 27: Screen Installation... -
Page 11: Oxo Panel Configuration
SERIES 3000-T ASSEMBLY & INSTALLATION INSTRUCTIONS XII. OXO Panel Configuration Note: Check customer order for proper panel configuration and orientation. Assemble and install the frame as indicated on previous sections III – VIII of this manual. Insert the sliding panels as indicated on previous section “XO”... - Page 12 SERIES 3000-T ASSEMBLY & INSTALLATION INSTRUCTIONS 7. Anchor False Jamb to the Frame and Structure • Add the Sill Block using (1) #8 PHP-TEK, 3/4” screw (Figure 33). • Attach the false jamb to the sill block using a (1) #10 PHP-A, 3” screw. •...
Need help?
Do you have a question about the 3000-T Series and is the answer not in the manual?
Questions and answers