Bravo Italia 1/3.2 Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

INTRODUCTION

Model:

Bravo Italia 1 / 3.2 Bravo Italia 2 / 3.2

Congratulations ! You are the owner of not only the finest slushie machine but

also the most versatile of its kind.

Please read all sections of this manual thoroughly to familiarize yourself with

all aspects of the unit.

For assistance (setting up the unit ,spare, or any other issue ) you can contact

us :

Ph 001.469.656.7599 from 7AM ET to 5 PM ET or email bravodrink@tin.it

WARRANTY AND PACKAGING

1 Year parts warranty on all the parts.

For warranty keep the original packaging: wooden crate , carton box and

polystyrene. Will not be authorized any return without original packaging.

INSTALLATION

NOTE: Note this appliance is not intended for use by persons(including

children) with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their

safety.

Children should be supervised to ensure that they do not play with the

appliance.

Type Y attachment

If the power supply cord is damaged , it must be replaced by the manufacturer

or its service agent or a similar qualified person in order to avoid a hazard.

1. Remove wooden crate and carton and other packing materials and keep

them for possible future use .

CAUTION! When handling the machine never grip it by the tanks/bowls

or cooling cylinders .The manufacturer and supplier will NOT be held

responsible for any damages which may occur through incorrect

handling.

2. Inspect the uncreated unit for any possible damage

1) If any damage, please call the delivering carrier immediately.

2)If the power cord is damaged, it must be replaced by the manufacturer,

service agent or a qualified electrician in order to avoid any hazard.

3. Install the unit on a counter top that will support the combined weight of the

dispenser and product, bearing in mind what is stated in the preceding

point 1, CAUTION paragraph.

Bravo Italia 3 / 3.2

Table of Contents

Need help?

Do you have a question about the 1/3.2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Bravo Italia 1/3.2

Page 1 INTRODUCTION Model: Bravo Italia 1 / 3.2 Bravo Italia 2 / 3.2 Bravo Italia 3 / 3.2 Congratulations ! You are the owner of not only the finest slushie machine but also the most versatile of its kind. Please read all sections of this manual thoroughly to familiarize yourself with all aspects of the unit.
Page 2 Note The freezing time of slushie depends according to the composition of the mixture the ambient temperature and the initial product temperature. Model Bravo Italia 1 / 3.2 Bravo Italia 2 / 3.2 Bravo Italia 3 / 3.2 Bowl (n) Capacity (gal) 1X3.2...
Page 3 Cleaning instructions 1 Drain all slushie out of machine with auger running. When machine is nearly empty , pour water in the tank and empty. 2 Fill again the tank with 2 gallons of cold water 3 Add beverage dispenser sanitizer if available (following the Instruction of the producer) 4 Drain the unit , then fill the unit with 2 gallons water, run auger for no more then 1 minute ( machine can ‘t work with only water for more then 1...
Page 4 DESCRIPTION OF CONTROLS Number that you read on the display after the 300 seconds countdown are the temperature inside the bowls in Celcius Model 1 bowl A is active ( B and C are not active ) Model 2 bowls A and B are active ( C is not active ) A is the bowl on the left , B is the bowl on the right Model 3 bowls A, B and C are active A is the bowl on the left , B in the middle C is the bowls on the right...
Page 5 Light ON : Slushie mode, slushie will be produced. When the light is ON ,the machine will start working ,there is a 6 seconds countdown. The magnetic valve will now be open. A 300 seconds countdown will start now. After 300 seconds, the compressor will start to refrigerate and will automatically stop when the slushie is ready.
Page 6 4.Separate Control Switch A 、B、 C switch You will find switches at the right side panel of the machine which controls each bowl/tank separately. 1. Press A switch -Start or stop left bowl 2. Press B switch - Start or stop middle bowl 3.
Page 7  figure 1 figure 12 4.Slide the outer spiral out and then the inner auger (fig.4) figure 2 5.Remove the bowl gasket from its seat(fig .5) figure 4 figure 3 figure 6 figure 5 6.Dismantle the faucet assembly(fig .6) 7.Slide the drip tray out and empty it. Cleaning Clean all removed parts and cooling cylinder using warm and mild nonabrasive food-grade detergent.
Page 8 3. Assemble the faucet by reversing the disassembly steps(fig.6) 4.Fit bowl gasket around its seat (fig.8) Figure 8 Use the silicone faucet terminal when the unit is used as cold beverage dispenser. Please remove the silicone faucet terminal when you use the machine in the slushy mode NOTE: The largest rim of the gasket faces the rear wall.
Page 9 5.Push the bowl/tank towards the rear wall of the unit until it fits snugly around the gasket. The front fastening hooks must properly engage (fig.11). Use fresh mix to remove any remaining sanitizer from the bottom of the bowls/tanks. Drain this solution and do not rinse out the machine.
Page 10 Note -To shorten slush recovery time and increase production, the bowl should be refilled after the product level is lower than half of the evaporator cylinder. -Before restarting the unit, ensure that no blocks of ice have formed, if so remove them before switching on the unit.
Page 11 Inside Auger Cover-Drip Pan/tray Drip Pan/Tray Display Board ON/OFF Button Front Panel Spring Bolt Accessory-Compressor Compressor Control/Main Board Electromagnetic Valve Chute-Control Board Regulating Spring Back Panel Sealing-Middle Plate Middle Plate Back Cover-Reducer Nuts-Back Cover Gear Motor Lining-Middle Plate Cover- Adjustable Bolt Adjustable Bolt Drive Support-Cover Drive Support...

This manual is also suitable for:

2/3.2 3/3.2