1. Manuals
  2. Brands
  3. Crary Manuals
  4. Cables and connectors
  5. Air Reel
  6. Owner's manual

Crary Air Reel Owner's Manual

Hide thumbs Also See for Air Reel:
Table of Contents

Advertisement

Quick Links

Download this manual
PN: 12069 R021506
Companion to 12086
OWNER'S
MANUAL
CASE IH
1010
1020
RECoRd SERIAl numbER HERE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Air Reel and is the answer not in the manual?

Questions and answers

Related Manuals for Crary Air Reel

Summary of Contents for Crary Air Reel

  • Page 1 OWNER’S MANUAL CASE IH 1010 1020 RECoRd SERIAl numbER HERE PN: 12069 R021506 Companion to 12086...
  • Page 2 Safety considerations shall be an integral and high prior- ity part of all engineering/design analysis and judgments involving Crary products. It is our stated policy that our products will be manufactured to comply with the safety standards specified by the American Society of Agricultural Engineers, the National Electrical Code, the Society of Automotive Engineers, and/or any other applicable recognized standards at the time manufactured.
  • Page 3 WIll bE voId. In the event of a failure, return the product, at your cost, along with proof of purchase to the selling Crary Company dealer. Crary Company will, at its option, repair or replace any parts found to be defective in material or workmanship.
  • Page 4 InSpECTIon AfTER dElIvERY Inspect your shipping cartons for damage. If you suspect any damage, contact the carrier (trucking company) right away. Unpack the shipping cartons and compare the contents with the parts listing on the packing slips. If any parts are missing or damaged, contact your local authorized dealer or call the factory for assistance.

  • Page 5: Table Of Contents

    ConTEnTS InTRoduCTIon ....................... 5 SAfETY ........................6 2.1 SAFETY ALERT SYMBOL ................................6 2.2 GENERAL SAFETY..................................7 2.3 OPERATING SAFETY .................................. 8 2.4 MAINTENANCE SAFETY ................................8 2.5 HYDRAULIC SAFETY .................................. 9 2.6 PTO SAFETY ....................................9 2.7 TRANSPORT SAFETY ................................10 2.8 STORAGE SAFETY ...................................
  • Page 6 ConTEnTS opERATIon ......................52 5.1 MACHINE COMPONENTS ................................ 53 5.2 PRE-OPERATION CHECKLIST ..............................54 5.3 MACHINE BREAK-IN ................................. 54 5.4 CONTROLS....................................55 5.5 INITIAL ADJUSTMENTS ................................56 5.5.1 INITIAL ADJUSTMENT ..................................56 5.5.2 REEL ADJUSTMENT ..................................56 5.5.3 TINE PITCH ADJUSTMENT ................................57 5.5.4 TORqUE LIMITER (SLIP CLUTCH) ..............................

  • Page 7: Introduction

    Safe, efficient, and trouble free operation of your Air Reel requires that you and anyone else who will be operating or maintaining the machine, read and understand the Safety, Operation, Maintenance, and Trouble Shooting information contained within the Operator’s...

  • Page 8: Safety

    SAfETY Section 2.1 SAfETY AlERT SYmbol This Safety Alert Symbol means: The Safety Alert symbol identifies important safety messages on the machine and in the manual. When you see this symbol, be alert to ATTEnTIon! bEComE AlERT! the possibility of personal injury or death. Follow the instructions in the safety message.

  • Page 9: General Safety

    SAfETY 2.2 gEnERAl SAfETY You are responsible for the SAfE operation and maintenance Read and understand the of your machine. You must ensure that you and anyone else Owner’s Manual and all safety who is going to operate, maintain or work around the machine decals before operating, main- are familiar with the operating and maintenance procedures and taining, adjusting or servicing...

  • Page 10: Operating Safety

    SAfETY 2.3 opERATIng SAfETY 2.4 mAInTEnAnCE SAfETY Follow ALL operating, maintenance, and safety information Read and understand the Owner’s Manual and all safety in this manual. decals before servicing, adjusting or repairing. Support the machine with blocks or safety stands when Install and secure all guards and shields before starting or working around it.

  • Page 11: Hydraulic Safety

    SAfETY 2.5 HYdRAulIC SAfETY 2.6 pTo SAfETY Always place all combine hydraulic controls in neutral be- Keep bystanders, especially children, away from drive fore disconnecting from combine or working on hydraulic shafts. system. Be extremely careful when working around PTO shafts, Make sure that all components in the hydraulic system are drivelines, or other rotating shafts.

  • Page 12: Transport Safety

    SAfETY 2.7 TRAnSpoRT SAfETY 2.10 SAfETY dECAlS Make sure you are in compliance with all local regulations Keep safety decals clean and legible at all times. regarding transporting equipment on public roads and Replace safety decals that are missing or have become highways.

  • Page 13: Sign-Off Form

    SAfETY 2.11 SIgn-off foRm Crary Company follows the general Safety Standards specified by the American Society of Agricultural Engineers (ASAE) and the Occupational Safety and Health Administration (OSHA). Anyone who will be operating and/or maintaining the equipment must read and clearly understand ALL Safety, Operating and Maintenance information presented in this manual.

  • Page 14: Safety Decals

    SAfETY dECAlS Section Good safety requires that you familiarize yourself with the various safety decals, the type of warning and the area, or particular func- tion related to that area, that requires your SAFETY AWARENESS. THInK SAfETY! WoRK SAfElY! Figure 3.1 - Decal Location PN 11002 - Decal, Warning PN 11001 - Decal, Caution REmEmbER - If safety decals have been damaged, removed or become illegible or parts have been replaced without safety decals,...

  • Page 15: Assembly

    Section Read all instructions to become familiar with the parts and procedure used before starting the actual work. You may refer to the parts catalog for additional aid in assembling the Air Reel. 4.1 unCRATIng Locate the manifold and bats crate.

  • Page 16: Eccentric Mount Installation

    12:00 position. noTE The back side of the manifold is opposite that of the large Air Reel decal. Assemble the RH & LH Eccentric Mount Plates (with the nylon rollers facing to the center of the manifold) to the RH &...

  • Page 17: Idler Gear Installation (Back Side Of Manifold)

    ASSEmblY 4.3 IdlER gEAR InSTAllATIon (bACK SIdE of mAnIfold) Assemble one idler gear assembly each to the RH & LH end clamps, and to all idler mount clamps (back side of manifold only) using one 3/8” X 2” bolt, three 3/8” flat washers and one 3/8”...

  • Page 18: Idler Gear Installation (Front Side Of Manifold)

    ASSEmblY 4.5 IdlER gEAR InSTAllATIon (fRonT SIdE of mAnIfold) Assemble one idler gear assembly each to the RH & LH end Tighten the 3/8” centerlock nuts to their specified torque. clamps, and to all idler mount clamps (front side of manifold Check the alignment of the reel bat arm assembly with the only) using one 3/8”...

  • Page 19: Air Tubes

    Figure 4.12 - Apply Self Adhesive Foam Seals. Make sure that the opening of the single and double air tubes face towards the rear of Air Reel (Figure 4.14). Drive three 11/32 X 7/8 self tapping screws through the air tube into the holes of the manifold (Figure 4.13) You may want to use an impact wrench for...

  • Page 20: Reel Bats

    Determine the correct orientation of the reel bat. The RH and LH pivot strap points to the rear of the Air Reel (Figure 4.16). Position the reel bats into the bearing bases. Reattach the plastic bearing caps, by installing one 5/16”...

  • Page 21: Hydraulic Motor

    ASSEmblY 4.8 HYdRAulIC moToR Determine the drive side of the manifold (RH side of ma- Install the hydraulic motor. chine). Line up the key on the shaft of the hydraulic motor Slide the shaft coupler onto the driveline shaft. with the key way of the shaft coupler. Insert the roll pin through the shaft coupler and driveline shaft Align the mounting holes of the hydraulic motor with hole.

  • Page 22: Eccentric Arm

    ASSEmblY 4.9 ECCEnTRIC ARm Bolt the eccentric arm assembly to the reel bat assemblies Slide an eccentric arm assembly over each end of the manifold, by inserting a bolt through the end shield and the pivot strap making sure that the end shield faces towards the outside. and tighten to specified torque.
  • Page 23 THIS pAgE InTEnTIonAllY lEfT blAnK. PN 12069 R021506...

  • Page 24: Gearbox/Fan Mount - Pre 1993 Series

    ASSEmblY 4.11 gEARboX/fAn mounT - pRE 1993 SERIES Position the mount plate support on the back of the header as shown in Figure 4.19 and clamp in place. Refer to Table HEAdER WIdTH dIm. “A” 4.1 for Dim. A. 15’ 9”...
  • Page 25 ASSEmblY 4.11 gEARboX/fAn mounT - pRE 1993 SERIES Attach gearbox mounting plates to the mount plate support (Figure 4.20). Do not tighten at this time. Lift the gearbox/fan into position using a floor jack or over- head hoist and secure to the support plate with four 1/2” bolts and washers.

  • Page 26: Gearbox/Fan Mount - 1993/1994 Series

    ASSEmblY 4.12 gEARboX/fAn mounT - 1993/1994 SERIES Position the mount plate support on the back of the header Attach gearbox mounting plates to the mount plate support as shown in (Figure 4.21) and clamp in place. (Figure 4.20). Do not tighten at this time. Mark and drill four 27/64”...
  • Page 27 ASSEmblY 4.12 gEARboX/fAn mounT - 1993/1994 SERIES Figure 4.22 - Gearbox/Fan Mount (1993/1994 Series). PN 12069 R021506...

  • Page 28: Gearbox/Fan Mount - 1995 And Later Series

    ASSEmblY 4.13 gEARboX/fAn mounT - 1995 And lATER SERIES Position the mount plate support on the back of the header Attach gearbox mounting plates to the mount plate support as shown in (Figure 4.23) and clamp in place. (Figure 4.24). Do not tighten at this time. Mark and drill the four 27/64”...
  • Page 29 ASSEmblY 4.13 gEARboX/fAn mounT - 1995 And lATER SERIES Figure 4.24 - Gearbox/Fan Mount (1995 and Later Series). PN 12069 R021506...

  • Page 30: Right Hand Drive Kit - Pre 1993 Series

    ASSEmblY 4.14 RIgHT HAnd dRIvE KIT - pRE 1993 SERIES Slide a bushing shield weldment over the RH end of the pRE 1993 RIgHT HAnd dRIvE KITS gearbox driveshaft and secure to the RH side of the gearbox KIT # dESCRIpTIon using two 1/2”...
  • Page 31 ASSEmblY 4.14 RIgHT HAnd dRIvE KIT - pRE 1993 SERIES Figure 4.25 - RH Drive Kit (Pre-1993 Series) PN 12069 R021506...

  • Page 32: Right Hand Drive Kit - 1993/1994 Series (15 Ft - 22.5 Ft)

    ASSEmblY 4.15 RIgHT HAnd dRIvE KIT - 1993/1994 SERIES (15 fT - 22.5 fT) • Insure that the three adjusting nut screws are 1993/1994 RIgHT HAnd dRIvE KITS backed off four turns and that the adjusting nut is KIT # dESCRIpTIon in a finger tight position (Figure 4.26).
  • Page 33 ASSEmblY 4.15 RIgHT HAnd dRIvE KIT - 1993/1994 SERIES (15 fT - 22.5 fT) Figure 4.27 - RH Drive Kit (1993/1994 Series) PN 12069 R021506...

  • Page 34: Right Hand Drive Kit - 1993 And Later Series (25 Ft - 30 Ft)

    Install the two flangettes and 1-1/8” hex bearing to the bear- ing mount bracket using 3/8” x 1” carriage bolts and 3/8” serrated flange nuts. Install the Crary RH driveshaft through the bearing so that the grooved end is on the left. PN 12069 R021506...
  • Page 35 ASSEmblY 4.16 RIgHT HAnd dRIvE KIT - 1993 And lATER SERIES (25 fT - 30 fT) Figure 4.28 - RH Drive Kit (1993 and Later Series: 25 - 30 FT) PN 12069 R021506...

  • Page 36: Right Hand Drive Kit - 1995 And Later Series (15 Ft' - 22.5 Ft)

    ASSEmblY 4.17 RIgHT HAnd dRIvE KIT - 1995 And lATER SERIES (15 fT’ - 22.5 fT) • Insure that the three adjusting nut screws are 1995 And lATER RIgHT HAnd dRIvE KITS backed off four turns and that the adjusting nut is KIT # dESCRIpTIon in a finger tight position (Figure 4.29).
  • Page 37 ASSEmblY 4.17 RIgHT HAnd dRIvE KIT - 1995 And lATER SERIES (15 fT’ - 22.5 fT) Figure 4.30 - RH Drive Kit (1995 and L Series) PN 12069 R021506...

  • Page 38: Hose Connector

    ASSEmblY 4.18 HoSE ConnECToR 4.18.1 WITH EXISTIng lIgHT ARm bRACKETS Assemble the hose connector weldment and light bracket Remove the bolts securing the OEM light arm bracket lo- assembly to the holes specified in Figure 4.33 below. Fasten cated on the top right hand side of the header beam (Figure with 3/8”...
  • Page 39 ASSEmblY 4.18 HoSE ConnECToR 4.18.2 WITHouT lIgHT ARm bRACKETS If your header does not have existing Ø.44 (7.16”) holes 3.19” If no holes exist on the header beam, use the hose connector (3-3/16”) apart, it may be necessary to drill the holes to mount weldment to measure and mark two holes.

  • Page 40: Reel Support (Manual)

    ASSEmblY 4.19 REEl SuppoRT (mAnuAl) 4.19.1 dISASSEmblY It may be necessary to consult your Case IH Parts Catalog for WARnIng identification of certain parts during disassembly. Remove reflector brackets from the front of the reel arms. Avoid crushing injury or death from fall of raised reel. Remove existing OEM reel and reel supports.
  • Page 41 ASSEmblY 4.19 REEl SuppoRT (mAnuAl) Figure 4.40 - Reel Support-Manual (Right Hand). Figure 4.41 - Reel Support-Manual (Left Hand). PN 12069 R021506...
  • Page 42 ASSEmblY THIS pAgE InTEnTIonAllY lEfT blAnK. PN 12069 R021506...

  • Page 43: Reel Support (Hydraulic)

    ASSEmblY 4.20 REEl SuppoRT (HYdRAulIC) 4.20.1 dISASSEmblY It may be necessary to consult your Case IH Parts Catalog for WARnIng identification of certain parts during disassembly. Remove reflector brackets from the front of the reel arms. Avoid crushing injury or death from fall of raised reel. Remove existing OEM reel and reel supports.
  • Page 44 ASSEmblY 4.20 REEl SuppoRT (HYdRAulIC) 4.20.2 ASSEmblY RIgHT HAnd SIdE: WARnIng Insert reel support pad into the reel support assembly and slide Avoid crushing injury or death from fall of raised reel. onto the reel arm. Before working on or under a raised reel, place all controls in Bolt the adjustment tube weldment onto the reel support neutral or off, stop combine engine, set parking brake, remove assembly and secure using 1/2 X 2-1/2 bolts and centerlock...
  • Page 45 ASSEmblY 4.20 REEl SuppoRT (HYdRAulIC) Figure 4.44 - Hydraulic Fore and Aft/Reel Support (Left Hand). Figure 4.45 - Hydraulic Fore and Aft/Reel Support (Right Hand). PN 12069 R021506...

  • Page 46: Reel To Header Installation

    ASSEmblY 4.21 REEl To HEAdER InSTAllATIon Set assembled reel into the half clamps on reel support WARnIng brackets so the brace clamps are inside of the reel support brackets. Avoid crushing injury or death from fall of raised reel. Center the reel between the reel arms. Before working on or under a raised reel, place all controls in Slide the brace clamps out to the reel support brackets and neutral or off, stop combine engine, set parking brake, remove...

  • Page 47: Manifold Tilt

    ASSEmblY 4.22 mAnIfold TIlT Slide the pivot clamp assembly over the LH end of the mani- WARnIng fold, and position it next to the reel support bracket. Do not tighten the clamp at this time. Avoid crushing injury or death from fall of raised reel. Place the tube cap over the end of the manifold tube and secure with the t-bolt clamp.

  • Page 48: Air Hose

    ASSEmblY 4.23 AIR HoSE Rotate 45° elbow to provide proper routing of hose to the WARnIng fan. Tighten t-bolt clamps that secure elbow to connector weldment and hose to elbow support band. Avoid crushing injury or death from fall of raised reel. Determine the correct length of flex hose to reach the fan and cut hose to length.

  • Page 49: Electrical Wiring

    ASSEmblY 4.24 ElECTRICAl WIRIng Mount the switch plate assembly in a convenient place inside WARnIng the cab (use either velcro or bolts). Run the red wires (with fuse-15 Amp & 6 Amp) to a power Place all controls in neutral or off, stop combine engine, set source.

  • Page 50: Optional Equipment

    ASSEmblY 4.25 opTIonAl EQuIpmEnT 4.25.1 AuXIlIARY REEl TInE KIT The Auxiliary Reel Tine Kit is recommended for crops that do Rotate the auxiliary reel tine assembly until the square end not move easily from the knife to the auger at the ends of the sets into the square hole of the pivot strap.
  • Page 51 ASSEmblY THIS pAgE InTEnTIonAllY lEfT blAnK. PN 12069 R021506...

  • Page 52: Gearbox / Fan Extension

    ASSEmblY 4.25 opTIonAl EQuIpmEnT 4.25.2 gEARboX / fAn EXTEnSIon Mount gearbox/fan extension to combine. Refer to owner’s manual for gearbox/fan installa- The gearbox/fan extension option is designed to extend the fan tion instructions. up to eliminate clearance problems with headers smaller than 20’ and combines with dual tires.
  • Page 53 ASSEmblY Figure 4.54 - Gearbox/Fan Extension Kit pART pART ITEm dESCRIpTIon ITEm dESCRIpTIon numbER numbER 15332 SCREW, 1/4”-20 X 1/4” SET 7022 KEY, 3/16” SqUARE X 1-1/4” PLAIN 15364 BOLT, 3/8” X 1-1/4” HHCS GR5 ZP 13014 U-BOLT, 3/8” X 3” X 4”, FAN MOUNT ZP ROTOR, FAN, 12.88”...

  • Page 54: Operation

    The Air Reel is designed to dramatically improve harvesting ef- Follow all safety instructions exactly. Safety is everyone’s busi- ficiency. Power is provided by the combine feeder and hydraulics.

  • Page 55: Machine Components

    The combination of these two systems results in superior harvesting efficiency. Please take the time to familiarize yourself with the proper adjustment and operation of your Finger Air Reel. You will be well rewarded for your time in increased performance and crop yields.

  • Page 56: Pre-Operation Checklist

    5.2 pRE-opERATIon CHECKlIST Efficient and safe operation of the Air Reel requires that each operator reads and understands the operating procedures and all related safety precautions outlined in this section. A pre-operation checklist is provided for the operator. It is important for both personal safety and maintaining the good mechanical condition of the machine that this checklist is followed.

  • Page 57: Controls

    opERATIon 5.4 ConTRolS Before starting to work, all operators should familiarize themselves fAn AIR volumE ACTuAToR: with the location and function of the controls and safety devices. Move the toggle to the OPEN position (Figures 5.1 & 5.2) Some machines may vary due to different models of combines to open the butterfly plate which increases air volume to the and headers.

  • Page 58: Initial Adjustments

    5.5 InITIAl AdjuSTmEnTS Since all applications of the Air Reel are not the same, based on WARnIng header and combine variations, some initial adjustments must be made to achieve peak performance of your Air Reel. Place all controls in neutral or off, stop combine engine, set parking brake, remove ignition key, wait for all moving parts to 5.5.1 InITIAl AdjuSTmEnT...

  • Page 59: Tine Pitch Adjustment

    opERATIon 5.5 InITIAl AdjuSTmEnTS WARnIng Place all controls in neutral or off, stop combine engine, set parking brake, remove ignition key, wait for all moving parts to stop, then properly block machine before servicing, adjusting, repairing, or unplugging. 5.5.3 TInE pITCH AdjuSTmEnT From the right side of the machine loosen the three 3/8”...

  • Page 60: Torque Limiter (Slip Clutch)

    5.5.4 ToRQuE lImITER (SlIp CluTCH) The Air Reel comes equipped with a torque limiter (slip clutch) on the main drive of the air reel. From the factory the torque limiter noTE is set in the engaged position. Before use, the slip clutch must be slipped and adjusted to ensure proper function.

  • Page 61: Operating Hints

    5.6 opERATIng HInTS The following are recommended adjustments the operator can The Air Reel is designed to be easily and conveniently moved make based on crop conditions. Any adjustments that involve from location to location. When transporting the machine, review...

  • Page 62: Storage

    Check all hydraulic lines for damage; replace as required. REmovIng fRom SToRAgE When removing from storage and preparing to use, follow this Air Reel Components procedure: • Air Tubes: repair or replace bent or damaged Clear the area of bystanders, especially small children.

  • Page 63: Service & Maintenance

    SERvICE & mAInTEnAnCE Section 6.1 mAInTEnAnCE CHECKlIST Along with a servicing interval, perform a visual inspection. Maintenance personnel can often detect potential problems from any unusual sounds made by such components as shafts, bearings and drives. These service recommendations are based on normal operating conditions. Severe or unusual conditions may require more frequent attention.

  • Page 64: Fluids And Lubricants

    SERvICE & mAInTEnAnCE 6.2 fluIdS And lubRICAnTS gREASE: Use an SAE multi-purpose high temperature SToRIng lubRICAnTS: Your machine can operate at top grease with extreme pressure (EP) performance meeting efficiency only if clean lubricants are used. Use clean contain- or exceeding the NLGI #2 rating for all requirements. Also ers to handle all lubricants.

  • Page 65: Gearbox Oil

    SERvICE & mAInTEnAnCE 6.4 gEARboX oIl CHECKIng THE gEARboX oIl lEvEl Check the gearbox oil level daily. Check more frequently if leaks exist around any of the plugs or shaft seals. The oil level in the gearbox should be no higher than the bottom of the driveshaft (Figure 6.1).

  • Page 66: Pto Lubrication

    SERvICE & mAInTEnAnCE 6.5 pTo lubRICATIon dAIlY Lubricate PTO cross journals. Make sure grease purges through all four bearings. EvERY 16 HouRS Lubricate PTO inner tubes. Telescoping members must have lubrication to operate successfully. Telescoping members with- out fittings should be pulled apart and grease should be added manually with a brush.

  • Page 67: Auger Drive Chain Tension And Alignment (1993 And Later Series)

    SERvICE & mAInTEnAnCE 6.7 AugER dRIvE CHAIn TEnSIon And AlIgnmEnT (1993 And lATER SERIES) At the end of every season or annually the auger drive chain AlIgnmEnT: tension and alignment should be checked. When checking Maintain correct chain alignment. A chain that is out of alignment the tension and alignment of the auger drive chain follow this causes excessive wear on the chain and sprockets.

  • Page 68: Idler Gear Tension

    SERvICE & mAInTEnAnCE 6.8 IdlER gEAR TEnSIon Every 40 hours the tension of the idler gears should be checked. ImpoRTAnT If the tension between the idler gears and internal gear sections of the reel bat arm assembly has any radial movement it will be necessary to make adjustments.

  • Page 69: Eccentric Rollers (Plastic)

    If replacement parts are needed, consult your local autho- Place all controls in neutral or off, stop combine engine, set rized Crary dealer. parking brake, remove ignition key, wait for all moving parts to stop, then properly block machine before servicing, adjusting, Reassemble the eccentric roller assembly as shown in repairing, or unplugging.

  • Page 70: Fan Housing And Air Hose

    Check the condition of all parts, especially the friction discs (Figure 6.10). If replacement parts are needed, consult your local autho- rized Crary dealer. Reassemble all components. Tighten nuts following an alternating cross pattern until the clutch slips momentarily upon initial startup and then con- tinues to operate normally.

  • Page 71: Friction Disc Torque Limiter (Slip Clutch) - Auger Driveshaft

    SERvICE & mAInTEnAnCE 6.12 fRICTIon dISC ToRQuE lImITER (SlIp CluTCH) - AugER dRIvESHAfT 1993 And lATER HEAdERS 6.12.1 Run-In And ToRQuE AdjuSTmEnT 6.12.2 mAInTEnAnCE It is recommended that the unit be run-in by slipping the After prolonged use, the auger driveline torque limiter should be inspected for wear.

  • Page 72: Troubleshooting

    If you encounter a problem that is difficult to solve, even after having read through this trouble shooting section, please call your local Crary dealer. Before you call, please have this manual and the serial number from your machine ready.

  • Page 73: Specifications

    SpECIfICATIonS Section 8.1 REEl SpECIfICATIonS SPEED OF HYDRAULIC DRIVE ....0 - 59 RPM DIAMETER (BAT REEL) ........... 48” NUMBER OF BATS ............6 8.2 fAn pERfoRmAnCE dATA Efficiency 4500 RPM FORWARD CURVE Pressure 8" OUTLET FAN ROTOR SIZE = 16.50" DIA X 3.00" WIDE Horsepower 1000 2000...

  • Page 74: Hydraulic Motor Data

    SpECIfICATIonS 8.3 HYdRAulIC moToR dATA Torqmotor Series mg08 Hydraulic Gear Motor: displacement (in³/rev) (cm³/rev) • Roller vane rotor set design. pressure (pSI) Continuous (Differential)ª 1800 • Full flow lubrication. (kg-/cm²) 126.6 • Shaft seal with stands full system pressure. Torque (in-lbs.) Continuous Pressure 1842 Continuous Flow...

  • Page 75: Hydraulic Fitting Torque

    SpECIfICATIonS 8.4 HYdRAulIC fITTIng ToRQuE TIgHTEnIng flARE TYpE TubE fITTIngS * flARE TYpE TubE fITTIngS nuT SIZE RECommEndEd TuRnS TubE SIZE ToRQuE ACRoSS To TIgHTEn Check flare and flare seat for defects that might cause vAluE * flATS (AfTER fIngER TIgHTEnIng) leakage.

  • Page 76: Bolt Torque

    The table shown below is for reference purposes only and its use by anyone is entirely voluntary, unless otherwise noted. Reliance on its contents for any purpose is at the sole risk of that person. Crary Co. is not responsible for any loss claim or damage arising therefrom.
  • Page 80 Crary Company A division of Terramarc Industries 237 12th St. nW • p.o. box 849 West fargo, nd 58078-0849 (701)282-5520 • fAX: (701)282-9522 www.crary.com manufactured in the united States of America by Crary Company...

Table of Contents

Save PDF