Related Manuals for Taco Marine GRAND SLAM 1000
Summary of Contents for Taco Marine GRAND SLAM 1000
- Page 1 TACO Marine® Grand Slam Outrigger Mounts GRAND SLAM 1000 ELECTRO-HYDRAULIC OUTRIGGER MOUNT INSTALLATION & OPERATION INSTRUCTIONS ®...
-
Page 2: Kit Contents
Kit Contents GS-1000 port head GS-1000 starboard head Pump and relay assembly Control box Required* *not included • POWER DRILL Valve manifold • 5/16" DRILL BIT • 1/4" DRILL BIT 25' 6-pin sensor cables • 3/16" DRILL BIT • 1/2" DRILL BIT Control panel and harness •... - Page 3 GS-1000 Thank you for purchasing the TACO Marine Grand Slam 1000 Electro- Hydraulic Outrigger Mount! As a family-owned and operated business since 1959, we take pride in offering the highest-quality, innovative products with excellent customer service. stand behind products 100 percent. If you have any questions about this mount or installation, please contact us by visiting tacomarine.com/contactus.
-
Page 4: Installation
INSTALLATION Preparing Mount Locations Using the drill template provided, align the long edge of the mount parallel with the edge of the hardtop; verify the orientation of the template with the bow and stern markings. 2. Drill the four (4) 5/16" corner mounting holes through the top into the hollow core of the top. 3. -
Page 5: Installing The Head Assembly
Installing the Head Assembly There are three (3) connection points with compression fittings on the base of each head. 2. To identify the Port and Starboard head, note that the round steel TACO logo on the head casting faces outboard with the arms facing to the stern. 3. -
Page 6: Operation And Maintenance
Install the Heads Remove the tie wraps securing the upper and lower mounting plates together. 2. Place a thin bead of marine-grade sealant under the mounting plate. 3. Secure the head using the 5/16”-18 bolts. 4. Through the lower access plate, verify all tubing is not kinked. Manually rotate head 90º to ensure it rotates freely. - Page 7 Operation Manual for Outriggers Control Panel POWER BUTTON (A) The power button on the control panel for the GS- 1000 is a lock-down button. When pressed, the button will light up and stay on until pressed again. Each time the power button is pressed, the system will reset the electronic system to the default setting.
- Page 8 APPENDIX Hydraulic Ports & Connection Diagram Use a Light Hydraulic oil ISO 32, like Mobile DTE 24 of an automotive ATF Fluid Approximate capacity: 1 qt. 8 / GRAN D S L AM 1 000...
- Page 9 Keypad Interface GRA N D SLA M 1000 / 9...
-
Page 10: How To Clean
How to clean Always use a mild, non-abrasive soap and fresh water. Thoroughly wash the aluminum with a soft towel or sponge to remove dried salt crystals and other contaminants. Rinse completely with fresh water. Safe Cleaners Harmful Cleaners Mild dish washing liquid, specialty marine cleaners: Bleach (Clorox, etc.) and mild abrasive cleaners: Sea Safe Boat Wash, Boat Wash Concentrate Ajax, Comet, Soft Scrub, Rubbing Compounds, etc. -
Page 11: Need Support
We’re here to help. Need Support? Contact Us 1.800.653.8568 support@tacomarine.com tacomarine.com 50 NE 179th ST Miami, FL. 33162 @tacomarine @taco_marine TACO Marine ® G RAND SLAM 1000 / 11... - Page 12 LEFT BLANK INTENTIONALLY 12 / GRA ND S L AM 1 000...
- Page 13 GS-1000 Drill Template STERN (6.00) Please print at 100 percent for accurate sizing. Slight scaling may still occur. Therefore, before drilling, it is recommended that all template dimensions be measured for accuracy. G RA ND SLA M 1000 / 1 3...
- Page 14 ®...
Need help?
Do you have a question about the GRAND SLAM 1000 and is the answer not in the manual?
Questions and answers