Seat ALHAMBRA Owner's Manual
  1. Manuals
  2. Brands
  3. Seat Manuals
  4. Automobile
  5. Alhambra
  6. Owner's manual

Seat ALHAMBRA Owner's Manual

Hide thumbs Also See for ALHAMBRA:
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ALHAMBRA and is the answer not in the manual?

Questions and answers

Related Manuals for Seat ALHAMBRA

Summary of Contents for Seat ALHAMBRA

  • Page 3 Foreword This Instruction Manual and its corresponding supplements should be read carefully to familiarise yourself with your vehicle. Besides the regular care and maintenance of the vehicle, its correct handling will help preserve its value. For safety reasons, note the information concerning accessories, modifications and parts changes. If selling the vehicle, give all of the onboard documentation to the new owner, as it should be kept with the vehicle.

  • Page 5: Table Of Contents

    Seat functions ......Seat belts .......
  • Page 6 Contents Wheels and tyres ......Wheels ....... . . Wheel trims* .

  • Page 7: Manual Structure

    Because this is a general manual for the ALHAMBRA, some of the equipment and functions that are described in this manual are not included in all types For the sake of the environment or variants of the model;...
  • Page 8 2. Operating instructions Information about the distribution of controls from the driver’s seat of your vehicle, about the options for adjusting the seat, about how to create a suit- able climate in the passenger compartment, etc. 3. Practical tips Advice relating to the driving, caring and maintenance of your vehicle and certain problems you can solve yourself.

  • Page 9: Safety First

    Dear SEAT Driver reduce the risk of damage to the lower part of the vehicle and the oil sump when driving over kerbs, or along dirt tracks or rough roads... SEAT recom- mends you have the guard fitted by a SEAT dealer.
  • Page 10 This applies to all passengers in the vehicle page 10. Correctly fasten your seat belt before starting to drive and keep it securely fastened throughout the journey. This applies to all passengers in the vehicle Driving abroad page 21.
  • Page 11 Caution such as the engine, transmission, running gear or electrical system. SEAT does not accept liability for any damage to the vehicle due to the use of Never drive through salt water as salt causes corrosion. Always rinse any a lower quality fuel, an inadequate service or the non-availability of genuine parts of the vehicle which have been in contact with salt water.

  • Page 12: Adjusting The Seat Position

    Always keep your feet in the footwell while the vehicle is in motion. Introduction Never, for example, put your feet on the surface of a seat or on the dash panel and never put them out of a window. Otherwise the airbag and seat...
  • Page 13 WARNING Every incorrect sitting position increases the risk of severe or fatal injuries If the seat belts are worn incorrectly or not at all, the risk of severe injuries in the event of accidents or sudden braking or manoeuvres. increases. Seat belts can provide optimal protection only if the belt web is All passengers must assume the proper sitting position and be properly properly worn.
  • Page 14 10 cm (4 inches) fig. The correct sitting positions for the driver and passengers are shown below. Adjust the height of the driver’s seat so that you can easily reach the top of the steering wheel.

  • Page 15: Transporting Objects

    Remove all objects from the passenger seat when this is folded down. Always transport heavy loads in the trunk and place the seat backs in a When the seat back is folded down, it presses on small and light objects vertical position.
  • Page 16 Transport heavy objects as far forward as possible in the luggage vehicle and injure other road users or damage other vehicles. compartment and lock the seat backs in the vertical position. Drive with due care and attention and think ahead.
  • Page 17 A sliding load could considerably affect the stability and safety of the vehicle resulting in an accident with serious consequences. Secure loads correctly so they do not move. When transporting heavy objects, use suitable ropes or straps. Lock the seat backs in vertical position. Safety First Operating instructions Practical tips...

  • Page 18: Seat Belts

    When travelling, children must be secured in the vehicle with a child restraint system suitable for their weight and height and with the seat Check the condition of all the seat belts at regular intervals. If you notice that belts correctly fastened page 40.
  • Page 19 They will switch off after a few seconds. A signal will be heard for a maximum of 90 seconds if the seat belts are not fastened as the car drives off and reaches a speed of more than 25 km/h or if the seat belts are unfastened while the vehicle is in motion.

  • Page 20: Why Wear Seat Belts

    0.0 / SET The seat belt status flashes for a maximum of 30 seconds when a seat belt in the rear seats is unfastened while the vehicle is in motion. A signal will also be heard if the vehicle is travelling at over 25 km/h.
  • Page 21 Passengers not wearing seat belts are not “attached” to the vehicle. As a thrown forward violently. result, in a frontal collision they will continue to move forward at the speed...
  • Page 22 The airbag is only deployed once. To achieve the best possible protection, the erly worn seat belts will seat belt must always be worn properly so that you will be protected in acci- not be thrown forward in dents in which no airbag is deployed. Vehicle occupants not wearing belts...

  • Page 23: Seat Belts

    If it is difficult to remove the seat belt from the guide, the seat belt may have chances of survival in a serious accident. Furthermore, properly worn seat...
  • Page 24 Pull the belt to ensure that the latch plate is securely engaged in the buckle. Unfastening the seat belt The seat belt must not be unfastened until the vehicle has come to a standstill Fig. 10 Insert the latch plate into the buckle.
  • Page 25 The seat belts for the centre seat in the second row of seats and for the seats size.
  • Page 26 “Adjusting the seat position”. Correct seat belt position The shoulder part of the seat belt must lie on the centre of the shoulder, never across the neck or the arm, under the arm or behind the shoulder. The lap part of the seat belt must lie across the pelvis, never across the stomach.
  • Page 27 The seat belt cannot provide optimum protection if it is not correctly worn and the backrest is not tilted slightly backwards. The seat belt itself or a loose seat belt can cause severe injuries if the belt moves from hard areas of the body to soft areas (e.g. the stomach).

  • Page 28: Seat Belt Tensioners

    Seat belts Belt tension limiter WARNING The belt tension limiter reduces the force of the seat belt on the body in the event of an accident. Never adjust the belt height while the vehicle is in motion. Note The relevant safety requirements must be observed when the vehicle or Seat belt tensioners components of the system are scrapped.
  • Page 29 Seat belts For the sake of the environment Airbag modules and belt tension devices may contain perchlorate. Observe the legal requirements for their disposal. Safety First Operating instructions Practical tips Technical Data...

  • Page 30: Airbag System

    Before each trip, every occupant must sit properly, correctly fasten the Introduction seat belt belonging to his or her seat and keep it fastened throughout the trip. This rule is valid for all occupants. Front airbags have been installed for both driver and passenger. The front...
  • Page 31 Airbag system WARNING (continued) Ensure deployed airbags and the system components involved are immediately replaced with new, SEAT-approved components for the vehicle. Have any repairs or modifications carried out at a qualified workshop. Qualified workshops have the necessary tools, diagnostics equipment, repair information and qualified personnel.
  • Page 32 Lights up location Possible cause Solution Have the system checked immediately by a specialist Instrument panel Fault in airbag system and seat belt tensioners. workshop. Have the system checked immediately by a specialist Fault in the airbag system. workshop. Dash panel Front passenger airbag disabled.
  • Page 33 Optimised seat belts for all seats. space within fractions of a second. When an occupant with the seat belt prop- Belt tension devices for the driver and front passenger and, where appli-...
  • Page 34 Airbag system Side airbags for the driver, front passenger and, where applicable, the Where applicable, mountings for the child seat upper retaining strap. outer seats of the second row of seats. Situations in which the frontal, knee, side and curtain airbag do not deploy: Left and right curtain airbags.
  • Page 35 Fig. 18 Location and deployment area of the front airbag for the front passenger. In conjunction with the seat belts, the front airbag system gives the front WARNING occupants additional protection for the head and chest in the event of a severe frontal collision.
  • Page 36 Front passenger airbag located in ing lamp on the instrument panel. Adjust the driver seat so that there is at least 25 cm distance between the dash panel. your chest and the hub of the steering wheel. If your physical constitution...
  • Page 37 Close the glove compartment on the front passenger side. As soon as the child seat is no longer needed on the front passenger’s The PASSENGER AIR BAG control lamp on the instrument panel will seat, reconnect the front passenger airbag.
  • Page 38 Any damage to the original seat upholstery or around the seams of the side airbag units must be repaired immediately by a qualified workshop. The side airbags are located in the outer cushion of the driver and front passenger seat backrests fig.
  • Page 39 Airbag system Curtain airbags Fig. 22 On the left side of the vehicle: location and deployment area of the curtain airbag. The area framed in red page 37, fig. 22 is covered by the curtain airbag when it is deployed (deployment area). Therefore, objects should never be placed or mounted in these areas.
  • Page 40 Airbag system WARNING (continued) Occupants of the front and outer rear seats must never carry any other people, pets or objects in the deployment space between them and the airbags. The built-in coat hooks should be used only for lightweight clothing. Do not leave any heavy or sharp-edged objects in the pockets.
  • Page 41 Never attach objects to the cover or in the deployment area of the knee airbag. Adjust the driver’s seat so that there is a distance of at least 10 cm (4 inches) between your knees and the location of the knee airbag. If your Fig.

  • Page 42: Airbag System

    Only one child may occupy a child seat. example, the accessory for the floor compartment) to fit the child retention If you are using a child seat with a base or foot, always install this base system correctly and securely.
  • Page 43 However, unlike adults and youngsters, children do not have fully developed Do not leave toys or other loose objects on the child seat or on the seat muscle and bone structures. In the event of an accident, children are subject while the vehicle is in motion.
  • Page 44 22 to 36 kg Forward-facing. Not all children fit in the seat of their weight group. Nor do all seats adapt to the vehicle. Therefore, always check whether the child fits properly in the child seat and whether the seat can be installed safely in the vehicle.
  • Page 45 Only use child seats that are approved for each vehicle. If a child seat is mounted on the front passenger seat, the risk of the child The frontal airbag on the front passenger side is highly dangerous for a child.
  • Page 46 If the vehicle is included in the manufacturer’s list and the ISOFIX child seat belongs to a seat category included in the list, then it can be used Always disable the front passenger airbag and leave it disabled.
  • Page 47 Removing the child seat on the vehicle seat. The seat belt must not be unfastened until the vehicle has come to a standstill There are two retaining rings, the so-called lower anchor points, on each rear Press the red button on the buckle. The latch plate is released from the seat or, where applicable, on the front passenger seat.
  • Page 48 Push the head restraint down as far as it will go. Ensure that it does not interfere with the seatbelt from the upper attachment. Tighten the strap so that the top of the child seat rests on the backrest.
  • Page 49 Always secure just one retaining strap from a child seat to a retaining ring (for TOP TETHER) on backrest on the rear seat in the luggage compart- ment. Never secure a child seat to the retaining rings.

  • Page 50: Integrated Child Seat

    Children must travel in a child seat appropriate to their weight and height Do not leave toys or other hard, loose objects on the child seat or on the while the vehicle is in motion.
  • Page 51 The integrated child seat can be fitted with a side head restraint. SEAT recom- Lifting the cushion mends use of the integrated child seat with the side head restraint fitted and Pull the unlock lever fig.
  • Page 52 Push the head restraint down as far as it will go. Fold the backrest of the rear seat back. Pull the rear seat and the backrest to check whether they are engaged properly. Fig. 32 Integrated child seats. seat belt routing with guide handle.
  • Page 53 Open the seat belt guide handle. The seat belt must lie flat and fit comfortably. Guide the seat belt by hand to pull the belt back in more easily and not Allow the belt to retract until it fits tightly over the child’s seat.
  • Page 54 Child safety Caution When lowering the integrated child seat, only press on the centre of the cushion page 51, fig. 33 . Otherwise the cushion could bend and not engage properly.
  • Page 55 Safety First Operating instructions Practical tips Technical Data...
  • Page 56 Fig. 34 Dash panel...

  • Page 57: Operating Instructions

    Activate telephone main menu or accept an incoming call SEAT information system control buttons , , OK, Overview of the dash panel Lever for ......... . .

  • Page 58: Instrument Panel

    Climatronic ........Right seat heating controls .
  • Page 59 Depending upon the equipment fitted in the vehicle, instead of a warning Symbol Meaning lamp, sometimes a symbol may be displayed on the instrument panel. Driver or passenger has not fastened seat belt. page 21 When certain control and warning lamps are lit, an audible warning is also heard.
  • Page 60 99 flashes: Engine oil sensor faulty. page 280 Headlight adjustment (Light Assist) on. lights: Insufficient engine oil. Colourless symbols Fault in airbag system and seat belt tensioners. page 31 Symbol Meaning Passenger front airbag is off (PASSENGER page 31 AIRBAG Electronic immobiliser active.

  • Page 61: Instruments

    Cockpit Instruments WARNING If the warning lamps and messages are ignored, the vehicle may stall in Introduction traffic, or may cause accidents and severe injuries. Never ignore the warning lamps or text messages. Additional information and warnings: Stop the vehicle safely as soon as possible. Indicator lamps page 56 Park the vehicle away from the traffic, ensuring that there are no easily...
  • Page 62 Cockpit View of instrument panel Fig. 35 Instrument panel, on dash panel. Displays on the screen Details of the instruments page 60, fig. page 61. Fuel reserve display page 265. Clock set button Speedometer. Press button to select the hour or minute display. Reset knob for trip recorder (trip).
  • Page 63 Cockpit Displays on screen Type of mes- Symbol Meanings sage colour A variety of information can be viewed on the instrument panel display Symbol flashing or lit; partly combined with page 60, fig. 35 , depending on the vehicle equipment: audible warnings.
  • Page 64 Cockpit displayed may be higher than the true outside temperature, as a result of the Start/Stop operating display heat produced by the engine. Updated information relating to the status is displayed on the instrument panel page 199. The temperatures measured range from -40°C to +50°C (-40°F to +122°F). Compass WARNING With the ignition on and the navigation system on, the cardinal point corre-...
  • Page 65 The inspection display appears on the instrument panel page 60, fig. 35 Fig. 36 Magnetic zones. SEAT differentiates between services with engine oil change (Maintenance Service) and services without engine oil change (Inspection Service). The The compass does not require calibration in vehicles for which the navigation service interval display only gives information for service dates which involve system was mounted at the factory.
  • Page 66 Technical progress has made it possible to considerably reduce servicing From the Service submenu, select the option Info. requirements. The technology used by SEAT ensures that your vehicle only When the service date has past, a minus sign is displayed in front of the has an maintenance service when it is necessary.

  • Page 67: Seat Information System

    A specialised dealer will be able to programme or modify additional func- Navigation Booklet “Navigation system” tions, according to the vehicle equipment. SEAT recommends visiting a qual- ified workshop. Some menu options can only be read when the vehicle is at a standstill.
  • Page 68 Cockpit Auxiliary heating page 167 Compass Activation Convenience page 72 On / Off programme Open door Switching off Manual Timer 1-3 automatic mode Childproof locks On / Off Time Anti-theft alarm confirmation On / Off Minute Handling windows Enabling Duration Operating mode Driver Heat...
  • Page 69 Cockpit Autohold Tourist light On / Off Service Info Reset Default setting Safety First Operating instructions Practical tips Technical Data...
  • Page 70 Cockpit Using the menus on the instrument panel If a message or vehicle symbol is displayed, press fig. 37 fig. 38). If managed from the windscreen wiper lever: the main menu list is displayed. If managed from the multifunction steering wheel: the main menu list is not displayed.

  • Page 71: System

    Cockpit Main menu Menu Function Parking Information and configurations of the park- page 167 heating ing heating: Menu Function switching the parking heating on or off. Information and possible configurations of page 69 Select the operating mode and duration. the multifunction display (MFI). Vehicle Current warning or information texts.
  • Page 72 Cockpit Menu Function With the ignition switched on, and memory 1 or 2 displayed, briefly press to change from one memory to another. Distance to empty Approximate distance in km (or miles) that can still (the distance you be travelled with the fuel remaining in the tank, The memory stores the values for the journey and the con- can travel with the assuming the same style of driving is maintained.
  • Page 73 Cockpit To switch off, press . The stored speed is deleted. Configuration Function Menu Manually erasing memory 1 or 2 Winter tyres Changing the visual and audible speed warnings. This Select the memory to be erased. function should only be used when the vehicle is fitted Press and hold for approximately two seconds.
  • Page 74 Cockpit Submenu Convenience Convenience menu Function When the vehicle is unlocked with the key, the following doors (depending upon the configuration) are unlocked: all doors: All of the doors will be unlocked. one door: see above Method 1. Manual Side of vehicle: The driver side doors will unlock. Open door Individually: Only the driver’s door is unlocked.
  • Page 75 121. Personal convenience settings When two people use a vehicle, SEAT recommends that each person always uses “their” own remote control key. When the ignition is switched off, or the vehicle is locked, the personal convenience settings are stored and automat- ically allocated to the vehicle key page 65.
  • Page 76 Unlocking and locking Unlocking and locking Vehicle key set Vehicle key Introduction Additional information and warnings: Adjustments to the SEAT information system page 65 Central locking and locking system page 78 Start and stop the engine page 175 Notes for the user...
  • Page 77 Unlocking and locking Vehicle keys Note With the vehicle key page 74, fig. 39 page 74, fig. 40 the vehicle may Only use the key button when you require the corresponding function. be locked or unlocked remotely. Pushing the button unnecessarily could accidentally unlock the vehicle or The vehicle key includes an emitter and batteries.
  • Page 78 Unlocking and locking Indicator on the vehicle key the indicator blinks several times, for example: for the convenience opening function. When the indicator light does not light upon pushing a button, the batteries of the vehicle key must be changed page 77.
  • Page 79 The vehicle key battery may contain perchlorate. Observe the legal requirements for their disposal. Fig. 44 Vehicle key: removing the battery. SEAT recommend having the batteries changed in a qualified workshop. The battery is located to the rear of the vehicle key, under a cover fig. Safety First...

  • Page 80: Central Locking And Locking System

    Additional information and warnings: The central locking system allows all doors and the tailgate to be locked and unlocked centrally. Personal convenience settings in the SEAT information system page 65 Vehicle key set page 74 From outside, using the vehicle key.
  • Page 81 Unlocking and locking Locking and unlocking the vehicle from the outside In the submenu Convenience in the Configuration menu, or by visiting a specialized workshop, special functions of the central locking system can be switched on or off page 65. In case of a vehicle key fault or central locking system fault, all doors can be locked or unlocked manually.

  • Page 82: Central Locking Button

    Unlocking and locking Locking and unlocking the vehicle from the inside Function Handling the buttons on the vehicle Unlocking the vehicle. Press button . Keep it pushed for the convenience opening. Lock the vehicle. Press button . Keep it pushed for the convenience locking function.
  • Page 83 Unlocking and locking The doors can be opened and unlocked individually from the inside by Driver’s door indicator light. pulling the inside door handle. If necessary, pull the door release lever twice. When the vehicle is locked: Meaning The driver’s door cannot be locked when it is still open. To avoid locking the vehicle key inside the vehicle when there is no-one inside.
  • Page 84 Unlocking and locking When does the system trigger an alarm? has been turned on will the other doors be available - but not unlocked - and the central locking button activated. The anti-theft alarm siren will be triggered for about 30 seconds accompa- nied by optical warning signals for about five minutes when the vehicle is If the vehicle battery is run down or flat then the anti-theft alarm will not locked and the following unauthorised actions are taken:...
  • Page 85 48 must be lit. To turn on the reading light, remove the key from the ignition or open a door. Fig. 48 Driver’s seat: button for switching off Push the button. A yellow warning lamp will light up in the button the interior monitoring until the vehicle is locked.
  • Page 86 Unlocking and locking When suspended objects are hung from the interior mirror (air freshener) WARNING or there are loose papers in the vehicle. If the separation net is fitted and moves (due to heating). A door held open by its retainer could be blown closed by the wind or may close if the vehicle is on a hill resulting in injury.

  • Page 87: Sliding Doors

    Unlocking and locking Sliding doors WARNING (continued) Never open the sliding doors when the vehicle is moving. Introduction Additional information: Manually opening and closing the sliding door Vehicle key set page 74 Central locking and locking system page 78 Emergency locking and unlocking page 315 WARNING If a sliding door is not correctly closed, it could open unexpectedly when...
  • Page 88 Unlocking and locking Function Necessary operations Function Necessary operations When the sliding door is released, open Press the fig. 51 button on the instru- Opening the sliding door from the door fully by pulling on the outside ment panel, on the remote control key the outside.
  • Page 89 Unlocking and locking Rollback anti-trap function of the electric sliding doors Electric child safety lock The rollback anti-trap function of the electric sliding doors can reduce the risk of injury when opening and closing the sliding doors If an object gets in the way of the sliding door while it is closing, it opens again.
  • Page 90 Unlocking and locking WARNING (continued) WARNING Ensure the tailgate is locked after closing, otherwise, it may open unex- When the electric child safety function is activated, the sliding door can be pectedly while driving. A closed tailgate should be flush with the corre- opened from the outside only.
  • Page 91 Unlocking and locking Warning indicator Opening the tailgate Lights up Possible cause Solution Stop driving immediately! The tailgate is open or not Open the tailgate and close it correctly shut. again. Several warning and indicator lamps should light up for a few seconds when the ignition is switched on.
  • Page 92 Unlocking and locking Closing the tailgate Opening with the ignition key Press the button on the vehicle key until the tailgate opens automatically. To open using the centre console control Press the button on the centre console page 89, fig. 53.
  • Page 93 Unlocking and locking Opening the tailgate WARNING Press and hold the button on the vehicle key until the tailgate opens automatically. Unsuitable or careless closing and locking of the tailgate could cause serious injuries. ALTERNATIVELY: Press and hold the button on the centre console for approximately 1 second page 89, fig.
  • Page 94 Unlocking and locking Interrupting the opening and closing process WARNING Tailgate opening and closing can be stopped by pressing one of the buttons. Each time one of the buttons is pressed, the tailgate moves to It is possible that the tailgate does not open completely or, if it is open, its initial position.

  • Page 95: Electric Windows

    Unlocking and locking Electric windows Opening and closing the electric windows Introduction Additional information and warnings: SEAT information system page 65 Central locking and locking system page 78 WARNING Careless use of the electric windows can cause serious injury. Fig. 57 In the driver door: Only operate the electric windows when nobody is in the way.
  • Page 96 Unlocking and locking Opening and closing the windows To stop the one touch function: Push or pull on the button of the corre- sponding window. Function Necessary operations Restoring one-touch opening and closing Opening: Press button The one-touch opening and closing function is not active after the vehicle Closing: battery has been disconnected or is flat and will have to be reset.
  • Page 97 Unlocking and locking If the window is still obstructed, it will stop at the corresponding position. WARNING (continued) When the button is operated within 10 seconds, the window will close without the anti-trap function Never leave children or disabled people alone in the vehicle if the doors are to be locked.

  • Page 98: Panorama Sliding Sunroof

    Unlocking and locking Panorama sliding sunroof* Opening or closing the panorama sliding sunroof Introduction Additional information and warnings: SEAT information system page 65 Central locking and locking system page 78 Emergency locking and unlocking page 315 WARNING Careless use of the panorama sliding sunroof can cause serious injury.
  • Page 99 Unlocking and locking Opening or closing the sunshade Function Switch setting Necessary operations page 96, fig. 58 To open the sliding sunroof completely: To choose the con- venience position Rotate the switch to the for the sliding sun- required position. roof: To close the sliding sunroof completely:...
  • Page 100 Unlocking and locking Panorama sliding sunroof: operation Closing without the roll-back function Switch page 96, fig. 58 should be in the closed position Convenience open/close function Panorama sliding sunroof: Within five seconds of triggering the anti-trap function, pull the control all the way back page 96, fig.
  • Page 101 Fault in adaptive light. page 103. Additional information and warnings: Rear fog light switched on. SEAT information system page 65 page 102. Changing bulbs page 327 Fog lights switched on Left or right turn signal.
  • Page 102 Lights and visibility Turn signal and main beam lever Several warning and indicator lamps should light up for a few seconds when the ignition is switched on. This signals that the lamp is working properly. They will switch off after a few seconds. WARNING If the warning lamps and messages are ignored, the vehicle may stall in traffic, or may cause accidents and severe injuries.
  • Page 103 Lights and visibility disconnected at a specialised workshop for those vehicles which do not have Note the menu Lights & Visibility. The turn signal only works when the ignition is switched on. The hazard warning lights also work when the ignition is switched off page 313.

  • Page 104: Light Switch

    Lights and visibility when the ignition is turned off when the ignition is on WARNING Fog lights, dipped beam and Lights off or daytime driving light The side lights or daytime driving lights are not bright enough to illuminate side lights off. the road ahead and to ensure that other road users are able to see you.
  • Page 105 Lights and visibility Automatic dipped beam control Main beam headlight control The automatic dipped beam control is merely intended as an aid and is not The main beam control (Light Assist) automatically switches the main beam able to recognise all driving situations. on and off within the limits of the system, regardless of prevailing conditions, traffic and vehicle speed .
  • Page 106 WARNING or the headlights may be adjusted at a specialised workshop. For further information, please refer to a specialised workshop. SEAT recommends The convenience features of the main beam control should not encourage visiting a qualified workshop.
  • Page 107 Lights and visibility When the “Coming home” function is on, if the vehicle door is opened “Coming Home” Necessary operations there is no audible warning signal to advise that the light is still on. – Switch off the ignition. – Briefly flash the headlights for approximately one sec- To switch sys- page 100.
  • Page 108 Lights and visibility Interior and reading lights Value Vehicle load status – Two front occupants, luggage compartment empty Button / Function All seats occupied, luggage compartment empty Switch All seats occupied, luggage compartment full. With trailer Switches interior lights off. and minimum support load Driver only, luggage compartment full.
  • Page 109 Lights and visibility Sun blind Swing the sun visor towards the door. Make-up mirror light There may be a make-up mirror, with a cover, on the rear of the sun visor. Introduction When the cover is opened fig. 64 a light comes on. The lamp goes out when the make-up mirror cover is closed or the sun visor WARNING is pushed back up.
  • Page 110 Lights and visibility Pull the sun blind by the handle page 107, fig. 65 up to the top. Hook both rings of the fastening rod in the spaces provided . Check that the sun blind is securely hooked into the spaces provided when it has been lowered To put the sun blind away, unhook it at the top and lower by hand Caution...

  • Page 111: Windscreen Wiper And Washer

    Lights and visibility Windscreen wiper and washer Warning lamp Introduction Lights up Possible cause Solution Top up the windscreen wiper Windscreen wiper fluid level Additional information and warnings: bottle as soon as possible too low page 113. Recirculation of air conditioning air page 159 Working in the engine compartment page 276...
  • Page 112 Lights and visibility Windscreen wiper lever Move the lever to the required position OFF Windscreen wiper off. Intermittent windscreen wipers wipe. Using the control fig. 66 adjust the interval (vehicles without the rain sensor), or the sensitivity of the rain sensor. LOW Slow wipe.
  • Page 113 Lights and visibility The rear wiper is automatically switched on when the windscreen wiper is To ensure the headlight washers work correctly in winter, any snow which has connected and the car is in reverse gear. got into the bumper jet supports should be cleaned away. If necessary, remove snow with an anti-icing spray.
  • Page 114 Lights and visibility Press the windscreen wiper lever downwards briefly page 110, fig. 66 Before driving, always lower the wiper arms. Using the windscreen wiper lever, the windscreen wiper arms return to their initial position. Lifting and returning windscreen wiper arms Place the wiper arms in the service position Only hold the wiper arms at the point where the blade is fixed.
  • Page 115 112, fig. 70 (arrow). To top up, mix water with a window cleaner recommended by SEAT To remove wax and coatings, we recommend a window cleaner containing Please follow the instructions for use found on the packaging.

  • Page 116: Rear Vision Mirror

    Caution If the electrolytic fluid comes into contact with eyes or skin, wash the Do not mix cleaning products recommended by SEAT with other products. area for at least 15 minutes with plenty of water, and seek medical advice. This could lead to flocculation and may block the windscreen washer jets.
  • Page 117 Lights and visibility Rear vision mirror Manual anti-dazzle function for rear vision mirror Basic position: point the lever at the bottom of the mirror forwards. Pull the lever to the back to select the anti-dazzle function fig. Automatic anti-dazzle function for interior mirror Legend for the fig.
  • Page 118 The new position of the mirror will be stored automatically and allocated Adjust the left-hand exterior mirror by turning the knob for- to the vehicle key that was used to unlock the vehicle. For vehicles with seat wards, backwards, to the left or to the right.
  • Page 119 Lights and visibility WARNING Note The exterior mirror heating initially heats up with a high power, after two Fold and unfold the exterior mirror, taking care to avoid injuries. minutes the heat will depend upon the ambient temperature. Only fold or unfold the exterior mirror when there is no-one in the way In the event of faults, the electric exterior mirrors can be adjusted manu- of the mirror.

  • Page 120: Seat Adjustment

    Pull the lever up or push down (sev- Adjusting the seat eral times if necessary) from its home height. position. Fig. 75 Front left seat controls. The controls are mirrored for the front right-hand seat. Mechanically and electrically adjusted controls can be combined on the seat.
  • Page 121 Caution So as not to damage the electrical components of the front seats, do not kneel on the seats or apply specific pressure to one point of the seat or back- Fig. 77 Adjusting the rest. lumbar support.
  • Page 122 Seats and storage compartments Seat adjustment is stopped when the engine is started. page 118, Function Necessary operations fig. 75 Adjusting the rear seats Pull the lever and adjust the backrest to the required position . The backrest must be engaged when the...

  • Page 123: Seat Functions

    WARNING The seat cushions can be heated electrically when the ignition is switch on. Inappropriate use of the seat functions can cause severe injuries. The backrest is also heated in some versions. Assume the proper sitting position before your trip and remain in it Switch off seat heating if there is nobody in the seat.
  • Page 124 Caution To avoid damaging the heating elements of the seat heating, please do not kneel on the seat or apply sharp pressure at a single point to the seat cushion and backrest. Liquids, sharp objects and insulating materials on the seat could damage Fig.
  • Page 125 A sound confirms the settings have been acti- than R. vated. Adjusting the wing mirrors for driving and assigning driver seat settings to a vehicle key Activate the memory function of the vehicle key Adjust the front seat and the exterior mirrors.
  • Page 126 Lift the backrest of the rear seat in an upright position. The entire seat folds backwards Make sure that the rear seat is securely engaged so that the seat belts can provide proper protection in the rear seats. The red mark fig.
  • Page 127 If the backrest or seat are folded down and are not correctly locked in place, no passenger should use them. When getting in or out, never lean or hold onto the folded seat on the second row of seats. WARNING If child seats are fitted to all the seats in the second row then it is possible Fig.
  • Page 128 Seat anchors and hinges exposed when the backrest of the front Lifting the backrest of the front passenger seat passenger’s seat is folded may lead to severe injuries in the event of an accident or sudden braking. Check that there are no objects or parts of the body in the hinge area.

  • Page 129: Head Restraints

    Always fit and adjust the head restraint properly whenever a person is occupying a seat. All occupants must correctly adjust the head restraint according to their height to reduce the risk of back injuries in the event of an accident.
  • Page 130 Adjust the head restraint to the correct position page 127. Removing the head restraints from the second and third row of seats Fold the backrest of the rear seat forwards page 130. Push the head restraint up as far as it will go...

  • Page 131: Centre Armrest

    On removing and fitting the head restraint, make sure the head restraint does and cause a serious accident. not hit the interior roof of the vehicle or the backrest of the front seat. This could damage the interior roof and other parts of the vehicle.

  • Page 132: Loading Luggage Compartment

    Secure all objects in the vehicle. Always keep equipment and heavy objects in the luggage compartment. Always transport heavy loads in the trunk and place the seat backs in a vertical position. Always use the fastening rings with suitable rope or straps.
  • Page 133 The ventilating slits between the heated rear window and the shelf must not be covered so that used air can escape from the vehicle. Folding down rear seats to create load space Fig. 89 Second row of seats: folding the rear seat rear seat as load space Safety First...
  • Page 134 When the seat is folded down, no adults or children should travel in it Folding the seats in the second row of seats for loading If necessary, open the belt loop and wind up the seat belt by hand.
  • Page 135 Press on the seat tray in the backrest until it is held in position by its Objects placed in the footrest area in front of and behind the rear seats magnets.
  • Page 136 Seats and storage compartments Rear shelf* Fig. 91 In the luggage compartment: rear shelf. Fig. 92 Remove the shelf supports then put them away safely The rear shelf can be fitted behind the second or third row of seats Opening the shelf Pull the shelf handle page 134, fig.
  • Page 137 Seats and storage compartments Release the shelf upwards by the side supports and guide it forward. WARNING Closing the shelf If the shelf is placed on one of the rear seats, this could cause serious Pull the unfolded shelf evenly on the guide backwards. injury in case of sudden braking or an accident.
  • Page 138 Seats and storage compartments Net partition* Fig. 93 Unfold the net partition then fold it again First remove the net from its bag and unfold it. Fold out the net partition Fold out the support transversal rods page 136, fig. 93 for the net partition fully in the direction of the arrow until you hear a “click”.
  • Page 139 Seats and storage compartments Fastening rings* Hook in the net partition on the rear right-hand side roof support by pressing on the rod. Secure the hooks of the net partition to the attachment rings in the left and right hand side foot rests on the second row of seats then tighten the straps.
  • Page 140 WARNING In case of an accident or sudden braking, the attachment elements in the parts of the rails close to the seats of the third row could injure seat occu- pants. Whenever the seats on the third row are to be occupied, remove the attachment elements from the rails or move them all the way back.
  • Page 141 Unsuitable or damaged ropes or straps may be released in case of sudden braking or an accident. As a result, objects may be fired through the Never secure a child seat to the attachment elements. passenger compartment causing serious injury or death.
  • Page 142 In case of an accident or sudden braking, the net attachment elements in rotate 90° to the left . The red mark on the attachment rod should not be the parts of the rails close to the seats of the third row could injure seat visible occupants.
  • Page 143 Always ensure that the baggage net supports are correctly inserted into the rails; the red mark should not be visible. Never secure a child seat to the baggage net supports. Caution The baggage net supports placed on the rail system can be damaged Fig.

  • Page 144: Roof Carrier System

    100 Given that the water drains have been incorporated into the roof for aerody- Releasing the baggage net namic reasons, only the SEAT approved basic supports and roof carrier The secured baggage net is taut systems can be used.
  • Page 145 Seats and storage compartments Securing the base supports and roof carrier system Ecological driving page 225 Wheels and tyres page 294 Accessories, parts replacement, repairs and modifications page 257 WARNING The risk of an accident is increased by transporting heavy or bulky loads on the roof, which affects the car’s handling by shifting the centre of gravity and increasing susceptibility to cross winds.
  • Page 146 Seats and storage compartments Always check the roof carrier system weight and the weight of the load to be WARNING transported and, if necessary, weigh them. Never exceed the maximum authorised roof load. If the base supports and the roof carrier system are incorrectly fitted or used in an unsuitable manner, the entire system could break free causing If you are using a roof carrier with a lower weight rating, you cannot transport accident and injury.

  • Page 147: Storage Compartments

    Seats and storage compartments Storage compartments WARNING Objects falling into the driver’s footwell could prevent use of the pedals. Introduction This could lead the driver to lose control of the vehicle, increasing the risk of a serious accident. Storage compartments must only be used to store lightweight or small Make sure the pedals can be used at all times, with no objects rolling objects.
  • Page 148 Seats and storage compartments Spectacle case in the roof console Compartment on the instrument panel* Fig. 102 On the roof Fig. 103 Storage console: Sunglasses compartment on the storage compartment. instrument panel. To open, press and release the button fig. 102 (arrow).
  • Page 149 Seats and storage compartments Compartment on the centre console Compartment in the front central armrest Fig. 105 Storage compartment in the front Fig. 104 Compartment in central armrest. the front centre console. There is an open compartment on the centre console fig.
  • Page 150 Seats and storage compartments Card compartments* Glove compartment Fig. 106 Centre console, Fig. 107 Glove compart- lower section: card ment. compartment. To the bottom of the centre console there is a compartment fig. 106 coins, cards, car park tickets and similar items. Note To avoid theft or use by others, do not use the compartment to store credit or ATM cards or similar.
  • Page 151 If you are using a child seat with a base or foot, always install this base or foot correctly and safely. If the vehicle has a storage compartment in the foot well in front of the last row of seats, this compartment cannot be used as designed;...
  • Page 152 To open, press the button on the drawer handle and pull the drawer out. A cup holder is built into the folding table page 152. To close, push the drawer under the seat until it clicks into place. To fold it back, push the folding table down as far as possible fig.
  • Page 153 Seats and storage compartments Other storage compartments WARNING The folding table must not be folded down while the vehicle is in motion to avoid the risk of injuries. Portable waste bin* Fig. 113 In the luggage compartment: Side storage compartment. Fig.
  • Page 154 Seats and storage compartments wise. To open the compartment , lift the cover. The factory-fitted CD WARNING changer can be located in the storage compartment .. The cover of the compartment can be used to safely store the covers of the rear shelf Clothing hung on the coat hooks could restrict the driver’s view and lead to supports.
  • Page 155 Seats and storage compartments Cup holders in front centre console WARNING Improper use of the cup holders can cause injury. Never place hot drinks in the drink holders. During sudden braking or driving manoeuvres, the hot drink could be spilled and lead to scalding. Ensure that bottles and other objects do not obstruct the pedals in the driver’s footwell.

  • Page 156: Ashtray And Cigarette Lighter

    Seats and storage compartments Cup holders, rear* Accessories, parts replacement, repairs and modifications page 257. WARNING Undue use of the ashtray and cigarette lighter may cause a fire or burns and other serious injuries. Never put paper or other flammable objects in the ashtray. Ashtray Fig.
  • Page 157 Seats and storage compartments Emptying the ashtray Replace the cigarette lighter in its insert. Remove the ashtray from the cup holder or lining of the door by pulling it upwards. WARNING After emptying the ashtray, insert it from above into the cup holder or door Undue use of the cigarette lighter may cause a fire or burns and other lining.
  • Page 158 Seats and storage compartments Vehicle sockets WARNING (continued) Depending on version of vehicle, you may have a 12-volt Never leave children unsupervised in the vehicle. The sockets and socket and/or a 230 volt socket. equipment connected to them can be used when the ignition is switched Should a connected electrical device overheat, switch it off and unplug it immediately.
  • Page 159 Seats and storage compartments Maximum power consumption LED on the socket page 156, fig. 120 Socket Maximum power consumption Steady green light: The child safety device is unlocked. The socket can now be used. 12 Volts 120 Watts Flashing red light: There is some kind of fault (e.g.
  • Page 160 (watts). The 230 Watt Euro power connector can be modified for 115 Watt appli- ances and vice versa. Consult a specialist shop for advice on accessories to adapt the connector. SEAT recommends visiting a qualified workshop.

  • Page 161: Climate Control

    Always ensure that you use the climate control and heated rear window When the cooling system is turned off, air coming from the outside will not to maintain good visibility. be dried. To avoid fogging up the windows, SEAT recommends leaving the Safety First Operating instructions...
  • Page 162 Heating, Ventilation and Air conditioning cooler (compressor) on. To do this, press the button. The button indicator neath the vehicle, this is completely normal and there is no need to suspect should light up. a leak. If the humidity and temperature outside the vehicle are high, condensa- Keep the air vents in front of the windscreen free of snow, ice and leaves tion can drip off the evaporator in the cooling system and form a pool under- to ensure heating and cooling are not impaired and to prevent the windows...
  • Page 163 Heating, Ventilation and Air conditioning Fig. 122 Detailed view of the centre console: Climatronic controls. To switch a function on or off, press the appropriate button. The corre- Control Additional information. Climatic page 160, fig. 121; Cli- sponding button will light up when a function is switched on. Press the button matronic fig.
  • Page 164 Press the button or the temperature control for the front pas- Air recirculation mode page 165. senger’s seat or the rear seats to set them to a different tem- perature. The button lights with an indicator. Climatronic: Automatic air recirculation page 165.
  • Page 165 Heating, Ventilation and Air conditioning Turn the temperature control to the centre position. WARNING (continued) Open the air outlets in the dash panel page 164. Stuffy or used air will increase fatigue and reduce driver and passenger Turn the air distribution control to the required position. concentration possibly resulting in a serious accident.
  • Page 166 Heating, Ventilation and Air conditioning Things to note If the filter loses efficiency prematurely due to use in areas with very high levels of air pollution, the filter must be changed more frequently than stated If the humidity and temperature outside the vehicle are high, condensation in the Service Schedule.
  • Page 167 Heating, Ventilation and Air conditioning There are additional vents in the footwell areas and in the rear of the Automatic air recirculation mode passenger compartment. Fresh air enters the vehicle interior in position . If the system detects a high concentration of hazardous substances in the ambient air, air recirculation mode is switched on automatically.
  • Page 168 Heating, Ventilation and Air conditioning WARNING (continued) Never use recirculation mode for long periods as it does not refresh the air inside the vehicle. If the cooling mode is switched off and air recirculation mode switched on, the windows can mist over very quickly, considerably limiting visibility. Switch air recirculation mode off when it is not required.

  • Page 169: Auxiliary Heater* (Additional Heater)

    (thin layers Switching the auxiliary heater on: only). Manually using the instant on/off button. page 160 Additional information and warnings: SEAT information system page 65 Manually using the remote control. page 168 Refuelling page 265...
  • Page 170 Heating, Ventilation and Air conditioning Remote control Meaning Battery light fig. 124 The auxiliary heater has been switched on Lights up green for around two seconds. using the button. The auxiliary heater has been switched off Lights up red for around two seconds.
  • Page 171 Heating, Ventilation and Air conditioning Replacing the remote control battery The remote control battery may contain perchlorate. Observe the legal requirements for their disposal. When the light page 168, fig. 124 on the remote control does not come on when the button is pressed, the remote control battery should soon be replaced.
  • Page 172 Heating, Ventilation and Air conditioning Menu options Description WARNING The auxiliary heater can be set to come on automati- Never programme the independent heating system to be activated and cally if required. To do so, select a timer: operated in closed, unventilated areas. The auxiliary heater fumes contain –...
  • Page 173 Heating, Ventilation and Air conditioning The heater will switch just once each time. The timer will also have to be switched back on every time it is required. Note Noise will be heard while the auxiliary heater is running. When the air humidity is high and the outside temperature low, the heating system may evaporate condensation from the auxiliary heater.
  • Page 174 Driving Driving Steering Control and warning lamps Introduction Lights up Possible cause Solution The steering system should be The power steering is not hydraulic but electromechanical. The advantage of (red) Power steering faulty. checked by a qualified workshop this steering system is that it disposes of hydraulic tubes, hydraulic oil, the as soon as possible.
  • Page 175 Driving Information on the steering flashes Possible cause Solution Fault in the steering column Do not drive on! Steering column electronic lock (red) electronic lock. Seek professional advice. If the driver’s door is opened before the ignition is switched off, the steering column electronic lock is activated via the ignition key or the sensor built into Gently turn the steering wheel to Steering column deviation.
  • Page 176 Driving WARNING WARNING The counter steering assistance system combined with ESP helps the Incorrect use of the steering wheel adjustment function and an incorrect driver to steer the vehicle in critical driving conditions. At all times, it is the adjustment of the steering wheel can result in severe or fatal injury. driver who steers the vehicle.

  • Page 177: Stopping And Starting The Engine

    Driving Stopping and starting the engine WARNING (continued) The assisted braking and steering systems, the airbag system, safety Introduction belts and certain safety equipment are only active while the engine is running. Immobiliser display The engine should only be switched off when the vehicle is at a stand- still.
  • Page 178 Driving Ignition lock Fig. 126 Vehicle key positions Car keys fig. 126 WARNING No key in the ignition lock: The steering lock may be activated. Unsuitable or careless use of the vehicle key could result in serious injury. Ignition off, all electrical components disconnected. Key can be Always take all the keys with you whenever you leave the vehicle.
  • Page 179 Driving For automatic gearbox vehicles the key can only be removed from the WARNING ignition lock if the gear selector lever is in position P. In this case, press and release the selector lever locking button. Never leave the vehicle unattended if the engine is running. The vehicle could move off suddenly, especially if it is in gear, resulting in an accident and serious injury.
  • Page 180 The airbags and belt tensioners do not work when the ignition is For this reason, the vehicle can only be used with a genuine SEAT key with the switched off.

  • Page 181: Changing Gear

    228 Emergency locking and unlocking page 315 Note The correct operation of the vehicle is only guaranteed when original SEAT WARNING keys are used. Rapid acceleration can cause loss of traction and skidding, especially on slippery ground. This could cause loss of control of the vehicle resulting in an accident and considerable damage.
  • Page 182 Driving Warning and control lamps Caution Failure to heed the warning lamps and text messages when they appear may Lights result in faults in the vehicle. Possible cause Solution (red) Brake pedal not pressed! Press brake pedal to the floor. To select a range of gears, press the brake pedal.
  • Page 183 Driving Pedals Floor mats should leave the pedal area free and unobstructed and be correctly secured in the footwell zone. In the event of failure of a brake circuit, the brake pedal must be pressed harder than normal to brake the vehicle. WARNING Objects falling into the driver’s footwell could prevent use of the pedals.
  • Page 184 Driving Manual gearbox: Engaging gears WARNING When the engine is running, the vehicle will start to move as soon as a gear is engaged and the clutch released. This is also the case with the electronic parking brake on. Never engage the reverse gear when a vehicle is moving forward. Caution To prevent damage and avoid premature wear, please observe the following: While driving, do not leave your hand resting on the gear stick.
  • Page 185 Driving Automatic gearbox*: Selecting gears When the ignition is on, the current position of the selector lever is shown on the instrument panel. Selector lever Denomination Meaning positions The drive wheels are locked mechanically. They only engage when the vehicle is at a Parking lock standstill.
  • Page 186 Driving To release the gear selector lever lock, press and hold the brake pedal with WARNING (continued) the ignition on. Press simultaneously on the selector lever lock. While the engine is running and with the D, S or R range of gears The selector lever lock is not engaged if the selector lever is moved quickly selected, keep the brake pressed to keep the vehicle at a standstill.
  • Page 187 Driving Changing gears with Tiptronic* vehicle remains in the currently selected gear. This is possible as long as the system is not changing gear automatically due to a traffic situation. Using Tiptronic with the selector lever Press the selector lever from position D to the right into the Tiptronic selector gate in “Automatic gearbox*: Selecting gears”...
  • Page 188 Driving Driving down hills When the accelerator pedal is pressed right down, the automatic gearbox will shift down to a lower gear, depending on road speed and engine speed. This The steeper the gradient, the lower the gear you will need. The lowest gears takes advantage of the maximum acceleration of the vehicle increase the engine braking work.
  • Page 189 Driving WARNING (continued) Caution If you stop on a hill with a gear ratio engaged, do not try to prevent the Responsibility for selecting the correct gear for each situation vehicle from rolling back by pressing on the accelerator. This could cause continues to lie with the driver, for example when overtaking, climbing a overheating and damage the automatic gearbox.

  • Page 190: Braking, Stopping And Parking

    Driving Braking, stopping and parking WARNING (continued) Always apply the electronic parking brake when you leave your vehicle Introduction and when you park. Never leave children or disabled people alone in the vehicle. They could The assisted braking systems include the anti-lock braking system (ABS), the release the electronic parking brake, activate the selector lever or gear brake assist system (BAS), the electronic differential system (EDS), the trac- stick and start the vehicle moving.
  • Page 191 Driving Warning and control lamps Lights up Possible cause Solution To turn on the TCS page 196. (yel- TCS is automatically activated Lights up Possible cause Solution TCS manually deactivated. when the ignition is switched on low) Together with the control or off.
  • Page 192 Driving Several warning and indicator lamps should light up for a few seconds when Caution the ignition is switched on. This signals that the lamp is working properly. They will switch off after a few seconds. Failure to heed the warning lamps and text messages when they appear may result in faults in the vehicle.
  • Page 193 Jump-start the vehicle page 338. moving, if the driver’s door is closed and the driver is wearing his/her seat When the electronic parking brake is applied or released, noises may be belt. In vehicles with a manual gearbox the clutch pedal should also be heard.
  • Page 194 If the brakes are not used frequently, or before the wheels touch the barrier or kerb. if rust has formed on the discs, SEAT recommends cleaning the pads and Special attention is required when driving through entrances, over ramps, discs by braking firmly a few times at a moderately high speed.
  • Page 195 Driving use more pressure on the brake pedal, and allow for longer stopping WARNING (continued) distances. Non-standard or damaged front spoilers could restrict the airflow to the Brake servo brakes and cause them to overheat. The brake servo only operates when the engine is running and the pressure applied by the driver on the brake pedal increases.
  • Page 196 If necessary, remove the wheels to check them thoroughly. vehicle is driven at such a speed that it will leave the road before ESP can SEAT recommends visiting a qualified workshop. intervene then the system cannot provide assistance.
  • Page 197 Driving when driving in a straight line. When the front wheels are turned, the normal WARNING (continued) ABS is activated. TCS and ESP, provide more security, do not take unnecessary risks while Braking assist system (BAS) driving. The brake assist system may reduce the required braking distance. The brake Brake assist systems can not overcome the laws of physics.
  • Page 198 Driving When driving through deep snow or on loose ground (gravel...). Note When freeing a trapped vehicle. To ensure that the ESP and TCS work properly, all four wheels must be Turn the TCS back on by pressing the button fig.
  • Page 199 Brake fluid specifications WARNING SEAT have developed a special brake fluid optimised for the brake systems of their vehicles. To ensure the optimum working of the brake system, SEAT If the brake fluid level is low or unsuitable/old brake fluid is used, the brake recommends the use of brake fluid in accordance with the VW 501 14 system may fail or braking power will be reduced.
  • Page 200 Driving Caution Brake fluid could damage the paintwork. Wipe off any brake fluid from the paintwork immediately. For the sake of the environment Brake fluid is an environmental pollutant. Collect any spilt service fluids and allow a professional to dispose of them.

  • Page 201: Start Assist Systems

    Driving Start assist systems Auto Hold function* Introduction Additional information and warnings: SEAT information system page 65 Braking, stopping and parking page 188 Vehicle battery page 289 Wheels and tyres page 294 Accessories, parts replacement, repairs and modifications page 257...
  • Page 202 3. When changing to idle speed. If the selector lever is placed in neutral (N). The driver’s seat belt must be buckled. The engine must be running. 4. If the engine is turned off or stalls. If the engine is switched off.
  • Page 203 Driving Start-Stop Function* Important conditions for the engine to automatically switch off The driver seat belt must be buckled. The driver door must be closed. The bonnet must be closed. The factory-fitted towing bracket must not be electrically connected to a trailer.
  • Page 204 Driving If the driver unbuckles his/her seat belt. If the driver’s door is opened. If the bonnet is opened. In vehicles with a manual gearbox: If a gear has been selected. Switching Start-Stop mode on and off manually Press the button on the centre console page 201, fig.

  • Page 205: Parking Sensor System

    Driving Parking sensor system* WARNING (continued) External sound sources can affect the parking distance aid signals. In Introduction this case, under certain circumstances, people and objects will not be detected. The parking sensor system assists the driver when parking. When the vehicle approaches an obstacle, forwards or backwards, an intermittent sound will Caution be heard, higher or lower depending on the distance.
  • Page 206 Driving Parking sensor system* the distance, the shorter the intervals between tones. If the vehicle is too close to the obstacle, the sound signal becomes constant. Switching the parking sensor system on and off Press the button fig. 139 when the ignition is switched on. Automatic on: select reverse gear.
  • Page 207 Driving Optical parking system* (OPS) The zone recorded by the sensors in front of and behind the vehicle is displayed on the factory-fitted radio or navigation system screen. Any obsta- cles are display in relation to the vehicle Function Necessary operations Switch on the parking sensor system page 204 Switching the display...
  • Page 208 Driving Displayed in colour on Distance from the vehicle to the Acoustic sig- the screen: colour of the obstacle segment if an obstacle is recognised in front: approx. 31 – 120 cm beeping Yellow behind: approx. 31 – 160 cm sound approx.

  • Page 209: Park Assist System

    Driving Park Assist system* WARNING (continued) Adjust your speed and driving style to visibility, road, traffic and Introduction weather conditions. The surface of certain objects and items of clothing and external sound The Park Assist system helps the driver to find a suitable place to park, to sources may have a negative affect on the park assist signals or on the insert the vehicle into parallel and perpendicular parking places and to leave system sensors or may not reflect its signals.
  • Page 210 When cleaning the sensors with high-pressure or steam cleaning equip- ment, spray the sensors briefly at a distance of no less than 10 cm. Note Contact a specialist workshop with any system faults. SEAT recommends visiting a qualified workshop. Parking using the park assist system Fig.
  • Page 211 Driving Parking perpendicular to the road: Drive next to the gap at a speed of no There is a system malfunction (system temporarily unavailable). more than 20 km/h and at a distance of between 0.5 m and 2 m. The TCS system is switched off or the TCS or ESP is working. The best parking results will be achieved if you position the vehicle as parallel as possible to the line of parked cars or the kerb.
  • Page 212 Driving A suitable parking space length is at least 1.1 m greater than the length Stopping the manoeuvre automatically of the vehicle. The park assist system stops the manoeuvre in the event of one of the following: If the results of the park assist system are not as good after changing the wheels, the system must store the perimeter of the new wheels.
  • Page 213 Driving status, load, inclination), the Park Assist system may stop the vehicle completely before an object. Press the foot brake Following the intervention of the brakes, the Park Assist will stop. WARNING Despite the assistance provided by the park assist system, do not run any risks when parking.

  • Page 214: Rear Assist System

    Driving Rear Assist system* WARNING The intelligent technology in the rear assist system cannot change the Introduction limits imposed by the laws of physics and by the system itself. Careless or uncontrolled use of the rear assist system may result in severe injuries and The camera fitted to the tailgate helps drivers during parking or reversing accidents.
  • Page 215 Driving User instructions Display help. The help list explains the surfaces and lines on the camera image. Press to exit help. Mute the sound. Adjust the display: brightness, contrast, colour. Switching on the orientation points for rear parking perpendicular to the road (mode 1).
  • Page 216 – If the tailgate is open. Note SEAT recommends that you practise parking with the rear assist system in - If the position and installation angle of the camera have been changed, a quiet location or in a car park to become familiar with the system, including e.g.
  • Page 217 Driving Parking perpendicular to the road (mode 1) Align the vehicle straight in the parking place using the help of the green orientation lines. Parking parallel to the road (mode 2) Fig. 147 Display: orienta- tion lines for the parking space behind the vehicle.
  • Page 218 Driving Turning point when parking. When the yellow line touches the curb or another limit of the parking space, the point for changing direction (magnifying glass) will have been reached. Free space required to park the vehicle parallel. The surface displayed must completely fit in the space.

  • Page 219: Cruise Control System

    Driving Cruise control system* Warning and control lamp Introduction The cruise control system (CCS) is able to maintain the set speed when driving forwards from approx. 20 km/h (12 mph). The CCS only slows down by reducing the accelerator but not by braking. Additional information and warnings: Changing gear page 179...
  • Page 220 Driving Cruise control operation Status page 217, fig. 149: CCS temporarily switched off. The set speed is displayed in small figures. System error. Contact a specialist workshop. CCS switched on. The speed memory is empty. The CCS is switched on. The set speed is displayed in large figures. WARNING If the warning lamps and messages are ignored, the vehicle may stall in traffic, or may cause accidents and severe injuries.
  • Page 221 Driving If the system detects a fault that could affect the working order of the CCS. Control position, If you increase the stored speed by using the accelerator for a certain Function control operations Action time. fig. 150 if the brake or clutch pedal is depressed. The stored speed is reached again If you change gears.

  • Page 222: Tyre Monitoring Systems

    Driving Tyre monitoring systems WARNING (continued) The tyre pressure should be that indicated on the label when the tyres Introduction are cold at all times page 298. Regularly check the cold inflation pressure of the tyres. If necessary, The tyre monitor indicator monitors the tyre pressure of each wheel during change the tyre pressure of the vehicle tyres while they are cold.
  • Page 223 Driving Control lamp The tyre monitoring system is set to the tyre pressure recommended by the manufacturer and indicated on the label page 298, fig. 173. Lights up or Solution Possible cause Elements of the tyre monitoring indicator flashes Stop the vehicle! Reduce your speed immediately! Stop the Tyre monitoring indicator with button.
  • Page 224 Driving WARNING (continued) Caution Failure to heed the warning lamps and text messages when they appear may If tyres are inflated at different pressures or a tyre pressure is too low, result in faults in the vehicle. a tyre may be damaged and burst resulting in a loss of control of the vehicle.
  • Page 225 Driving The vehicle is fitted with snow chains. The wheel on one axle is changed. There may be a delay in the reaction of the tyre monitoring indicator or it may not indicate anything under certain circumstances (e.g. sports driving, snow-covered or unpaved roads).

  • Page 227: Practical Tips

    Driving and the environment Practical tips Driving and the environment Running-in For the sake of the environment If the engine is run in gently, the life of the engine will be increased and the Please observe the instructions for running-in new components. engine oil consumption reduced.
  • Page 228 Start-Stop function on, the engine switches off automatically when the Switch off the seat heating when the seats have warmed up. vehicle is not moving. Switch off the heated rear window and the windscreen heating when the windows have demisted and are free of ice.
  • Page 229 It takes a few kilometres of driving for the engine to warm up and to normalise consumption. When purchasing engine oil, always observe legal requirements and ensure that the oil is approved by SEAT. Safety First Operating instructions...

  • Page 230: Engine Management And Exhaust Gas Purification System

    Driving and the environment Avoid carrying unnecessary loads WARNING The lighter the vehicle, the more economical and ecological the driving style. For example, an additional weight of 100 kg will increase fuel consumption The components of the exhaust system reach very high temperatures. This up to 0.3 l/100 km.
  • Page 231 Driving and the environment Warning lamps flashes Possible cause Solution Take the vehicle to a qualified Fault in the engine manage- Lights workshop as soon as possible Possible cause Solution ment (diesel engines). and have the engine checked. Take the vehicle to a qualified You should reduce speed accord- Fault in engine management workshop as soon as possible...
  • Page 232 The diesel particulate filter removes soot particulates from the exhaust gas. The filter retains these particulates and burns them. To assist the combustion process, SEAT recommends you avoid frequent short trips. Always use diesel with a low sulphur content page 268.

  • Page 233: Trailer Towing

    Vehicles with the Start-Stop function tow hitch may fail and the trailer will separate from the vehicle. With a SEAT factory fitted or retrofitted trailer bracket, the Start-Stop function is automatically deactivated when a trailer is connected. For trailer brackets...
  • Page 234 Never use a trailer with a new engine (for the first 1000 km or 600 miles) page 257. At SEAT, we recommend folding in the trailer hitch ball when a trailer is not being used. In case of a rear collision, the damage caused to the vehicle with...

  • Page 235: Driving With A Trailer

    If the car is supplied with a factory-fitted tow hitch it will already have the specialist workshop. SEAT recommends visiting a qualified workshop. necessary technical modifications and meet the statutory requirements for towing a trailer.
  • Page 236 Press the knob briefly fig. 153. The tow ball is released electronically Towing a trailer places additional demands on the vehicle. At SEAT, we and folds out automatically; the button indicator will blink. recommend additional services between the normal inspection intervals if Move the ball joint until it inserts and the button indicator lights.
  • Page 237 Trailer towing Installing a bicycle carrier to the tow hitch When the indicator remains lit and the tailgate is open, the tow ball has inserted correctly into the folded or deployed position. When the tailgate is closed, the indicator is turned off. The maximum load permitted for a bicycle carrier on the tow hitch ball is 75 kg, with a maximum distance of 300 mm from the support.
  • Page 238 Trailer towing Trailer electric socket Caution The electric connection between vehicle and trailer is a 13-pin socket. If the Do not leave the trailer connected to the vehicle when parked; place it on its trailer plug has seven pins, an adapter cable must be used. support wheel or its supports.
  • Page 239 Trailer towing For the sake of road safety, SEAT recommends using the maximum allowed WARNING drawbar load. The handling of the combined vehicle and trailer will be poor if the drawbar load is too low. If the load moves, the stability and safety of the vehicle and trailer combi- nation will be seriously affected and this could result in a serious accident.
  • Page 240 Trailer towing Hill starts with a trailer WARNING (continued) Depending on the hill and the gross combined weight, it is possible that the combined vehicle and trailer move backwards slightly when starting. Never try to stop the “snaking” by increasing speed. Always observe the speed limits for vehicles with and without trailers For a hill start with a trailer, proceed as follows: in each country.
  • Page 241 SEAT recommends visiting a specialist workshop to retrofit a tow hitch. For example, it may be necessary to adjust the cooling system or to include thermal plates.
  • Page 242 Note The figures may be different depending on whether additional equipment is Use only tow hitches approved by SEAT for the vehicle. fitted, for different models and for special vehicles. The maximum combined weights listed are only applicable for altitudes up to 1000 m above sea level.
  • Page 243 Trailer towing Caution Exceeding the maximum gross combined weight rating indicated could cause damage to the vehicle. Never exceed the gross combined weight rating. Safety First Operating instructions Practical tips Technical Data...

  • Page 244: Vehicle Maintenance And Cleaning

    Vehicle maintenance and cleaning Vehicle maintenance and cleaning Caring for and cleaning the vehicle exterior WARNING (continued) Harmful vapours may be produced when using car care products. There- Introduction fore, care products should only be used in well-ventilated spaces or in the open air.
  • Page 245 The vehicle paintwork is so durable that the car can normally be washed process. without problems in an automatic car washing tunnel. However, wear and damage to the paintwork will depend on the type of car wash used. SEAT Caution recommends the use of car washes without brushes.
  • Page 246 Vehicle maintenance and cleaning Caution WARNING To prevent damage to the vehicle, please observe the following before The incorrect use of high pressure cleaning equipment could result in entering an automatic car wash: permanent damage, visible or invisible, to the tyres or other materials. This Compare the distance between the vehicle wheels and the distance could result in serious accident.
  • Page 247 These deposits can only be removed with a special product or cleaning cloths. Wax deposits on the windscreen could cause the wiper blades to judder. SEAT recommends you wipe the wax deposits off the wind- Caution screen with a soft cloth each time after you have washed the vehicle.
  • Page 248 Vehicle maintenance and cleaning Cleaning and changing windscreen wiper blades graphite layer is damaged, the noise of the water as it is wiped across the windscreen will be louder. Check the condition of the wiper blades regularly. If the wipers scrape across the glass they should be changed if they are damaged, or cleaned if they are dirty Damaged wiper blades should be replaced immediately.
  • Page 249 Never use fuel, nail varnish remover, paint thinner or similar products to Clean chrome parts with a damp cloth. SEAT recommends the use of a chrome clean the windows. care product to clean stains and dirt from chrome surfaces. Use a soft dry cloth to polish chrome parts.
  • Page 250 The use of products containing degreasing agents to de-ice the locks may rust the lock cylinder. Caring for and cleaning alloy wheels Remove road salt and brake dust by washing the wheels approximately once a fortnight. Use an acid free detergent to clean the wheel rims. SEAT recom-...
  • Page 251 The protective coat on the undercarriage may wear through use system. while driving. Therefore, SEAT recommends that the protective coating on the undercarriage and on the running gear should be regularly checked, and Leaves and other loose objects should be regularly cleaned away from the repaired if necessary.

  • Page 252: Caring For And Cleaning The Vehicle Interior

    The dye from many items of modern clothing (e.g. dark jeans) is not always ance with the manufacturer’s instructions. fast. Seat upholstery (material and leather), especially when light-coloured, Only use approved or recommended care products. may visibly discolour if the dye comes out of clothing (even when used correctly).
  • Page 253 Dry the area gently with a soft dry cloth. Note Persistent stains, Apply cleaning paste directly to the stain and SEAT recommends you take the vehicle to a qualified workshop to treat any e.g. chocolate or treat. stains on the upholstery caused by the discolouration of clothing. make-up.
  • Page 254 In the event of spilt liquids, dry immediately with an absorbent cloth to Then wipe off with a soft, dry cloth. prevent the liquid penetrating through the leather. Cleaning the vehicle SEAT recommends the use of a damp cotton or wool cloth for general cleaning.
  • Page 255 Use a clean, damp, lint-free cloth to clean parts. If this does not provide satisfactory results, we recommend using a If the seat belt is very dirty, the belt retractor may not work correctly thus special solvent-free plastic cleaning product.
  • Page 256 Only allow the seat belt to retract when it is completely dry. WARNING Check the condition of all the seat belts at regular intervals. If the webbing or other parts of the belt are damaged, the vehicle should be taken to a qualified workshop immediately and the belts should be replaced.

  • Page 257: Notes For The User

    Caution are kept in good condition and are legible. SEAT does not accept liability for any damage to the vehicle due to the use If a vehicle part, bearing a safety certificate, label or plate, is replaced, the of a lower quality fuel, an inadequate service or the non-availability of qualified workshop should attach the information back in the same place.
  • Page 258 Note If electrical equipment is used near an aerial built-into the window, you may observe interference in the reception of AM stations. Notes on SEAT repairs WARNING Repairs or modifications which are not performed correctly may result in damage or errors in the vehicle operation, affecting the efficiency of the driver assist and airbag systems.

  • Page 259: Accessories, Parts Replacement And Modifications

    Any retro-fitted equipment which has a direct effect on the vehicle and/or the repair information and qualified personnel. way it is driven must be approved by SEAT for use in your vehicle and bear the e mark (the European Union’s authorisation symbol). This includes cruise Only mount parts with the same specifications as the parts fitted at control systems or electronically controlled suspension.
  • Page 260 Repairs and technical changes Therefore, fluids must always be stored closed in their original container. When performing repairs and technical modifications, SEAT’s directives Never store fluids in empty food containers or bottles as other people must be observed! may accidentally drink the fluid.
  • Page 261 The vehicle owner should keep the documentation for the additional equip- nations not approved by SEAT are used, or if the vehicle height is lowered, the ment safely and hand it over to the scrap yard at the end of the vehicle’s suspension is stiffened or the suspension springs, telescopic arms, dampers, service life.
  • Page 262 Information stored by the control units SEAT has approved your vehicle for use with two-way radios providing the Your vehicle is fitted at the factory with a series of electronic control units following conditions are observed: responsible for the engine and gearbox management.
  • Page 263 For example, in vehicles with airbag systems, values may be harmful to the human body. International committees and data relating to speed of impact, seat belt status, seat positions and airbag authorities have established limits and directives in order to ensure electro- activation times may be stored.
  • Page 264 Accessories, parts replacement and modifications If the vehicle is fitted with a suitable hands-free device, it will comply with the WARNING legislation in many countries which only permits the use of mobile phones inside vehicles using a hands-free device. When using a mobile phone without a connection to an exterior aerial, the maximum permitted levels of electromagnetic radiation may be exceeded.
  • Page 265 Accessories, parts replacement and modifications Jacking points for raising vehicle The vehicle should not be lifted using lifting platforms with lift pads containing fluid. When raising a vehicle using a platform or jack, a series of precautionary measures are required. Never raise the vehicle with a lifting platform or jack unless you have received training in how to do so and know how to lift the vehicle safely.
  • Page 266 Accessories, parts replacement and modifications Caution Never raise the vehicle at the engine oil sump, the gearbox or the rear or front axles. Always use an intermediate rubber support to prevent damage to the vehicle underbody. Check that the arms of the lifting platform are able to move freely.

  • Page 267: Checking And Refilling Levels

    WARNING Refuelling or handling fuel carelessly can cause an explosion or fire For safety reasons, SEAT does not recommend carrying a spare fuel canister resulting in serious burns and injuries. in the vehicle. Fuel could be spilled and catch fire, above all in case of an Always make sure that you correctly close the fuel cap to avoid evapo- accident and this applies to a full container as well as empty containers.
  • Page 268 Fig. 159 On the instru- are not covered by the SEAT warranty. If you refuel with the wrong type of fuel, ment panel: Fuel gauge for never start the engine. This applies to even the smallest amount of the wrong petrol and diesel.
  • Page 269 Checking and refilling levels Filling the tank with petrol or diesel WARNING Driving with insufficient fuel reserve could result in the vehicle breaking down in traffic and a serious accident. If the fuel level is too low then the fuel supply to the engine can become irregular especially on slopes.

  • Page 270: Fuel

    Checking and refilling levels Closing the tank cap Engine oil level page 280 Screw on the tank cap clockwise until it you hear it click into position. Engine coolant level page 284 Press the tank flap until you hear it click into place. The tank flap must be Brake fluid level page 188 flush with the body contour.
  • Page 271 For this reason, you should use good quality petrol SEAT recommends the use of sulphur-free or low sulphur fuel to reduce containing a mixture of additives. These additives will help to prevent corro- consumption and prevent engine damage.
  • Page 272 In countries with different climatic conditions, other types of diesel fuel are stances should this fuel be used. It could damage the fuel system and subse- available that are suitable to local temperatures. SEAT qualified workshops quently lead to engine failure!
  • Page 273 Checking and refilling levels The addition of biodiesel to diesel by the diesel producer according to Measurement of the urban cycle starts with an engine cold Standard EN 590 or other equivalent (DIN 51628 in Germany, for example) is Urban cycle start.

  • Page 274: Selective Catalytic Reduction* (Adblue)

    Refill AdBlue over the next kilo- Do not allow the AdBlue to run too low. metres or miles as indicated (yel- The AdBlue reserve is low. page 274. SEAT recommends low) contacting a specialist work- WARNING shop. AdBlue is an irritant, corrosive liquid that can cause injuries if it touches...
  • Page 275 SEAT recommends contacting a specialist workshop. If you are unable to visit a qualified specialist workshop, you should temporarily refill with a minimum of 10.0 litres of AdBlue. Only refill using AdBlue expressly approved by SEAT. Safety First Operating instructions...
  • Page 276 Checking and refilling levels Refilling AdBlue Fig. 161 At the rear left of the luggage compart- ment: AdBlue tank, behind a cover panel. Fig. 162 AdBlue tank with filler neck cap and refilling bottle. To refill AdBlue, the vehicle must be on flat ground and not, for example, Opening the tank filling neck parked on a kerb or slope.
  • Page 277 Refilling AdBlue avoid other people mistaking it for something else. Only use AdBlue that is approved by SEAT and that complies with the Keep the AdBlue out of the reach of small children. ISO 22241-1 Standard. Only use genuine bottles.

  • Page 278: Working In The Engine Compartment

    Checking and refilling levels Working in the engine compartment WARNING (continued) If you have to work underneath the vehicle, you must use suitable Introduction stands additionally to support the vehicle, there is a risk of accident!. The jack is not intended for this kind of work and its failure could lead to severe injuries.
  • Page 279 Checking and refilling levels WARNING (continued) WARNING (continued) When the engine is warm or hot, the cooling system is pressurised! Do If any work has to be performed when the engine is started or with the not unscrew the cap on the expansion tank when the engine is hot. Other- engine running, there is an additional, potentially fatal, safety risk from the wise, coolant may spray out under pressure causing burns and serious rotating parts, such as the drive belts, alternator, radiator fan etc as well as...
  • Page 280 Checking and refilling levels Wait for the engine to cool down. WARNING (continued) Always keep children and other people far from the engine compartment. Never work close to heaters, heat sources or places exposed to Ensure that the vehicle can not move off unexpectedly. flames or sparks.
  • Page 281 Checking and refilling levels Opening and closing the bonnet Before opening the bonnet, make sure that the windscreen wiper arms are in place against the windscreen Open the driver’s door. Pull the release lever page 279, fig. 163 in the direction of the arrow. The bonnet is released from the lock carrier by a spring mechanism Lift the bonnet using the release lever page 279, fig.

  • Page 282: Engine Oil

    Checking and refilling levels Before driving, always lower the wiper arms. accordance with legislation and with the utmost respect for the environment. Engine oil Warning and control lamps Introduction Lights up Possible cause Solution Switch the engine off. Check the Additional information and warnings: Insufficient engine oil.
  • Page 283 Caution Only use engine oils whose specifications are expressly approved by SEAT. The use of any other type of engine oil could cause engine damage! Preparations No additives should be used with engine oil. Any damage caused by the Park the vehicle on flat ground so that the engine oil reading is correct.
  • Page 284 Stop the engine and wait a few minutes for the oil to drain back into the Only refill using engine oil expressly approved by SEAT and in small quan- sump. When the engine has cooled down, immediately check the oil level and tities (not more than 0.5 l or 1/2 a quarter of a gallon at a time)
  • Page 285 Always dispose of engine oil with the utmost respect for the environment. the engine oil and filter changed. SEAT recommends visiting a qualified work- Never dispose of used engine oil in places such as a garden, woods, drains, shop.

  • Page 286: Engine Coolant

    ! Have the Coolant temperature warning lamp and gauge work carried out by a qualified workshop if you are uncertain. SEAT recom- mends visiting a qualified workshop. Negligent work can cause serious injury.
  • Page 287 Checking and refilling levels Gauge WARNING Lights up position Possible cause Solution If the warning lamps and messages are ignored, the vehicle may stall in fig. 167 traffic, or may cause accidents and severe injuries. Stop the vehicle! Always observe any lit warning lamps and text messages. Stop the vehicle safely as Never ignore the warning lamps or text messages.
  • Page 288 Caution Never mix genuine additives with other additives that are not approved by SEAT. Otherwise, you run the risk of causing severe damage to the engine and the engine cooling system. The engine coolant G 12 plus-plus can be mixed with G 12 plus and G 11.
  • Page 289 Remove the cap very carefully not unscrew the cap on the expansion tank when the engine is hot. Other- Only refill using new engine coolant according to SEAT specifications wise, coolant may spray out under pressure causing burns and serious page 285) injury.
  • Page 290 Checking and refilling levels but another type of water to top up the coolant, a specialist workshop must immediately replace all of the fluid in the engine cooling system. Only top up coolant to the top level of the marked area page 286, fig.

  • Page 291: Vehicle Battery

    ! Have the work carried out by a qualified workshop if you are uncertain. battery. SEAT recommends visiting a qualified workshop. Negligent work can cause Keep children away from acid and the battery itself! serious injury.
  • Page 292 Checking and refilling levels Checking the electrolyte level of the vehicle battery Do not expose the battery to direct sunlight over a long period of time, as the intense ultraviolet radiation can damage the battery housing. If the car is left standing for long periods, protect the battery from extreme cold temperature so that it does not “freeze up”...
  • Page 293 WARNING your vehicle before you purchase one. SEAT recommends you have the Working with the vehicle battery involves a risk of corrosion, explosions battery replaced by a qualified SEAT workshop.
  • Page 294 Checking and refilling levels Start-Stop systems ( page 201) are equipped with a special battery. There- On starting the engine, the power supply from the 12-volt sockets and the fore, it must only be replaced with a battery of the same specifications. cigarette lighter may be interrupted for a short time.
  • Page 295 Checking and refilling levels Caution Never disconnect the battery if the ignition is switched on or if the engine is running. This could damage the electrical system or electronic compo- nents. Never plug in accessories that supply current, such as solar panels or a battery charger, to the 12-volt sockets or the cigarette lighter.

  • Page 296: Wheels And Tyres

    600 km (370 miles). SEAT recommend that all work on tyres and wheels is carried out by a quali- fied workshop. They have the necessary special tools and replacement parts, Check tyre pressures regularly and ensure they are maintained at the trained personnel and facilities for disposing of the old tyres.
  • Page 297 In some cases, this may also be true for the same model of wheel. Inspect the tyres regularly for damage (punctures, cuts, cracks, dents). Please refer to the vehicle documents or ask at a SEAT qualified workshop. Remove any foreign bodies found on the outside of the tread provided they have not passed through the wall of the tyre page 300.
  • Page 298 Wheels and tyres SEAT recommends you take the vehicle to a qualified workshop to have the WARNING tyres changed. Old tyres, even if they have never been used, may lose air or burst unex- Tyres that are over 6 years old pectedly while driving, resulting in serious accident or damage.
  • Page 299 WARNING Never use tyres which are larger than SEAT approved tyres. If the tyres are The use of worn or damaged wheel rims could make driving more too big, they may knock or rub against the chassis or other components, dangerous and result in serious accidents and damage.
  • Page 300 Wheels and tyres If you use tyres that are approved by SEAT, you can be sure that the true correct tyre pressures, especially if driving at high speeds. Incorrect tyre pres- tyre dimensions will be correct for your vehicle. For other tyre models, the tyre sure causes premature wear and could cause tyre blow-out.
  • Page 301 Wheels and tyres Tread depth and wear indicators WARNING (continued) Tyre pressures should be checked regularly, at least once a month and before long journeys. Adjust the pressures of all the tyres to the vehicle load. Never deflate excess pressure from hot tyres. Caution Take care not to tilt the manometer when placing it on the valve.
  • Page 302 Wheels and tyres are equally spaced around the tyre tread. Certain marks on the tyre walls (for Foreign bodies in the tyre example, the letters “TWI” or other symbols) indicate the position of the wear Do not remove foreign bodies if they have penetrated through the tyre indicators.
  • Page 303 If you use V-rated tyres the speed limits and tyre pressure will be determined assistance immediately. by engine size. Please ask your SEAT qualified workshop for further informa- If there is no visible exterior damage, drive slowly and carefully to the tion on the maximum permitted speed and the required pressures for the nearest qualified workshop and have the vehicle checked.
  • Page 304 Wheel rims may be damaged or scratched if the chains come into direct Snow chains must only be mounted on the front wheels, even on all-wheel contact with them. SEAT recommends the use of covered snow chains. drive vehicles, and only with the tyre and rim combinations listed below:...
  • Page 305 Wheels and tyres Tyre code Tyre code (example) Meaning Make, logotype Manufacturer Product name Name of tyre assigned by manufacturer. P215 / 55 R 16 Size: Passenger vehicle code. 215 Nominal width between walls, in mm. Height/width ratio in % Tyre type (R indicates "radial").
  • Page 306 Wheels and tyres Tyre code (example) Meaning Tyre code (example) Meaning DOT BT RA TY5 1709 TRACTION AA Braking capacity of tyre on wet surface (AA, A, B Tyre identification number (TIN , may be only on or C). interior wall of wheel) and date of manufacture: TEMPERATURE A Tyre temperature resistance at higher test speeds DOT The tyre complies with the legal require-...

  • Page 307: Wheel Trims

    Wheels and tyres max. 190 km/h (118 mph) Caution max. 200 km/h (124 mph) Remove and remount wheel trims taking care to avoid damage to the max. 210 km/h (130 mph) vehicle. max. 240 km/h (149 mph) max. 240 km/h (149 mph) max.

  • Page 308: Changing A Wheel

    Wheels and tyres Fitting hubcaps The anti-theft wheel locking bolt has a special cap. This cap only fits on anti- theft locking bolts and is not for use with standard wheel bolts. Before mounting the full hubcap, the anti-theft wheel lock must be threaded into position page 308, fig.
  • Page 309 Wheels and tyres 10. Take the vehicle tool kit out of the luggage compartment. WARNING (continued) 11. Remove the wheel trims page 305. Ensure the ground on which you park is flat and solid. If necessary, support the jack on a wide solid base. WARNING If you are changing a wheel yourself, you should be familiar with the Failure to follow the checklist prepared for your own safety could lead to...
  • Page 310 Wheels and tyres Wheel bolts Loosen the wheel bolts only about one turn before raising the vehicle with the jack. If the wheel bolt is very tight, you may be able to loosen it by pushing down on the end of the wheel brace carefully with your foot. Hold on to the car for support and take care not to slip.
  • Page 311 Wheels and tyres If wheel bolts are rusty and it is difficult to tighten them, the threads should WARNING (continued) be replaced and cleaned before checking the torque. The bolts and threads should be clean, free of oil and grease and easy Never grease or lubricate wheel bolts or the wheel hub threads.
  • Page 312 188. You should only use a jack approved by SEAT for your vehicle. Other jacks, even those approved for other SEAT models, might slip out of place. When towing a trailer: unhook the trailer from the towing vehicle and park it correctly.
  • Page 313 Wheels and tyres Changing a wheel WARNING (continued) Only fit the jack at the prescribed jacking points. The claw of the jack should grip the reinforcement nerve on the underbody page 310, fig. 181. You should never have any limbs beneath a raised vehicle which is only supported by a jack.
  • Page 314 Wheels and tyres Lower the car with the jack. Tighten all of the wheel bolts clockwise . Tighten the bolts in diag- onal pairs (not in a circle). Put the caps, trim or full hubcap back on page 305. WARNING If the wheel bolts are not treated suitably or not tightened to the correct torque then this could lead to loss of vehicle control and to a serious acci- dent.

  • Page 315: If And When

    If and when If and when In case of emergency Protecting yourself and securing the vehicle Introduction Additional information and warnings: Braking, stopping and parking page 188 Emergency locking and unlocking page 315 Vehicle tools page 321 WARNING Fig. 183 In the centre of A faulty vehicle in traffic represents a risk of accident for the driver and for the instrument panel: other road users.
  • Page 316 If and when Connect the electronic parking brake page 188. WARNING Move the selector lever to its intermediate position or to P page 179. Stop the engine and remove the key from the ignition page 175. The components of the exhaust system reach very high temperatures. This could cause a fire and considerable damage.

  • Page 317: Emergency Locking And Unlocking

    The first aid kit must comply with legal requirements. Check the expiry date of the contents of the first aid kit. WARNING Fire extinguisher Opening and closing doors carelessly can cause serious injury. There is a Fire extinguisher underneath the passenger seat. Safety First Operating instructions Practical tips Technical Data...
  • Page 318 If and when Manually locking and unlocking the driver’s door WARNING (continued) If the vehicle is locked from outside, the doors and windows cannot be opened from the inside. Never leave children or disabled people alone in the car. They could be trapped in the car in an emergency and will not be able to get themselves to safety.
  • Page 319 If and when Note The anti-theft alarm is not activated when the vehicle is locked manually using the key page 78. Locking the passenger side door and sliding doors manually Fig. 187 Emergency locking of the vehicle using the vehicle key. The passenger side door and the sliding doors can be locked manually.
  • Page 320 If and when Emergency unlocking the tailgate Push the release lever fig. 189 in the direction of the arrow to unlock the tailgate. Manually open the tailgate. Fig. 188 From the luggage compartment: Remove the tailgate cover. Fig. 189 From the luggage compartment: Manually unlocking the tailgate.
  • Page 321 If and when Manually closing the panorama sliding roof Rotate the Allen bolt to close the panorama sliding roof. Re-install the lining. Bring the vehicle to a specialist workshop to check the panorama sliding roof given that the emergency closing operation could damage general oper- ation or the anti-trap function of the panorama sliding roof.
  • Page 322 If and when Manually unlocking the gear selection lever The emergency release mechanism is located underneath the gearbox cover panel to the right-hand side. To release the gear selector lever mechanism, a suitable tool is required, for example a screwdriver. Preparations Apply the parking brake.

  • Page 323: Tools

    If and when Tools* Location Introduction When securing the vehicle in case of a breakdown, please note the legal requirements for each country. Additional information and warnings: Working in the engine compartment page 276 Changing a wheel page 306 Fig. 194 In the luggage In case of emergency page 313 compartment, viewed...
  • Page 324 The individual elements of the on-board toolkit fig. 195 Adapter for antitheft bolt. SEAT recommend you carry the wheel bolt adapter in the vehicle tool kit at all times. The code number of the anti- theft locking bolt is stamped on the front of the adapter. In the event of loss, another adapter can be ordered using this number.

  • Page 325: Fuses

    If and when Fuses WARNING (continued) Never repair a fuse. Introduction Never replace a fuse with a metal strip, staple or similar. Due to the constant update of vehicles, fuse assignments depending on Caution equipment and the use of the same fuse for various electrical components, at the time of printing this manual it is not possible to provide an up-to-date To avoid damage to the vehicles electric system, before replacing a fuse summary of the electrical components fuse positions.
  • Page 326 If and when Vehicle fuses Identifying fuses by colours Colour Amp rating purple light brown Brown Blue Yellow White or transparent Green Fig. 196 On the driver- side dashboard: fuse box orange cover. To open the dashboard fuse box Reach behind the cover with your hand fig.
  • Page 327 If and when Caution Always carefully remove the fuse box covers and refit them correctly to avoid problems with your vehicle. Protect the fuse boxes when open to avoid the entry of dust or humidity. Dirt and humidity inside fuse boxes can cause damage to the electrical system.
  • Page 328 If and when Caution If you replace a fuse with higher-rating fuse, you could cause damage to another part of the electrical system.

  • Page 329: Changing Bulbs

    Changing bulbs requires a certain amount of manual skill. If you are unsure, ment is a hazardous area and could cause severe injury. SEAT recommends that you consult an qualified workshop or request assist- Discharge lamps work with high-voltage and can cause serious or fatal ance from a specialist.
  • Page 330 If and when Indicator Note A fault in the LED on the tail lights will not be indicated. However, if the fault Lights up Possible cause Solution affects all the LEDs then this will be indicated by the indicator A vehicle exterior lighting Replace the faulty bulb.
  • Page 331 If and when 13. Check if the new bulb is working. If the bulb is not working, it may not WARNING (continued) have been correctly fitted, it could be damaged or the connector may not be correctly connected. Always complete the operations given in the checklist and observe the 14.
  • Page 332 If and when page 329, fig. 200, Indicators (small lamp Dipped beam head- page 329, fig. 201 Daylight driving lights Main beam headlights Side lights holder) lights Always take the checklist into account and take the necessary actions page 328. Open the bonnet page 276.
  • Page 333 If and when To replace the xenon headlights bulb Turn signal indicators Cornering lights Always take the checklist into account and take the necessary actions page 328. Open the bonnet page 276. Rotate the cover fig. 202 in the direction of the arrow and remove Rotate the lamp holder Press the wire clip downwards fig.
  • Page 334 If and when To replace the front bumper bulbs Always take the checklist into account and take the necessary actions page 328. Pull the cover forwards, in the direction of the arrow fig. 204. Unscrew the attachment screw fig. 204 using the screwdriver from the on-board tools page 321.
  • Page 335 If and when To replace the tailgate light bulbs Always take the checklist into account and take the necessary actions page 328. Open the tailgate page 88. Extract the cover carefully using the flat part of the screwdriver as a lever ( page 322, fig.
  • Page 336 If and when To replace the tail light bulbs Fig. 208 On the side of the luggage compartment: To remove the left and right hand side tail lights. remove the cap; attachment screw. Removing the tail light units Complete operations only in the sequence given: Rear light, left Rear light, right Always take the checklist into account and take the necessary...
  • Page 337 If and when Assembling the tail light units Rear light, left Rear light, right Complete operations only in the sequence given: Unscrew the attachment screw page 334, fig. 208 using the screwdriver from the on-board tools page 321. The bolt is Rear light, left Rear light, right secured in its position.
  • Page 338 If and when Changing the number plate light Fig. 211 Number plate Fig. 210 On the rear light: To remove the lamp bumper: number plate holder. lights. Complete operations only in the sequence given: Fixed number plate light Bolted number plate light Always take the checklist into account and take the necessary actions page 328.
  • Page 339 If and when Fixed number plate light Bolted number plate light Insert the lamp holder into the number plate light and rotate all the way Insert the lamp holder into the number plate light. in the opposite direction to the arrow page 336, fig.

  • Page 340: Starting Assistance

    If and when Starting assistance WARNING (continued) The battery providing current must have the same voltage (12V) and Introduction approximately the same capacity (see markings on battery) as the flat battery. If the engine fails to start because of a discharged battery, the battery of Never charge a frozen or recently thawed battery.
  • Page 341 If and when Positive pole on the starting assistance points How to jump start: description Fig. 213 Jump lead connection diagram when the assistance vehicle Fig. 212 In the engine does not have a Start- compartment: positive Stop system: flat battery pole for starting assist- and battery supplying ance...
  • Page 342 If and when The vehicles should not touch. Otherwise, current may be allowed to flow Switching on when the positive poles are connected. Start the engine of the vehicle supplying current and let it run at idling speed. Connect the clamps so they have good metal-to-metal contact with the termi- Start the engine of the car with the flat battery and wait two or three nals.

  • Page 343: Towing And Tow Starting

    If and when WARNING (continued) WARNING The non-insulated parts of the battery clamps must not be allowed to When towing the vehicle, the handling and braking efficiency change touch. Also, the cable connected to the positive pole of the battery should considerably.
  • Page 344 If and when Vehicles with an electronic parking brake, given that it is possible that the Towing vehicles with an automatic gearbox brake will not be disengaged. Note the following for a towed vehicle: If the vehicle battery is flat, it is possible that the engine control units do Make sure the gear selector lever is in the N position.
  • Page 345 If and when Fitting the front tow ring Caution The tow ring must always be completely and firmly tightened. Otherwise, it could be released while towing and tow-starting. Fitting the rear tow ring Fig. 215 On the right- hand side of the front bumper: Screw in the towing ring.
  • Page 346 If and when Screw in the tow ring into its position anticlockwise as far as it will go As the power assisted steering does not work if the engine is not running, . Use a suitable tool to firmly tighten the tow ring in its location. you will need more strength to steer than normally.

  • Page 347: Technical Data

    General notes on the technical data Technical Data General notes on the technical data Outstanding information Abbreviations used in the Technical Data section Abbrevia- Meaning tion Important Kilowatt, engine power measurement. All data in the official vehicle documents take precedence Pferdestärke (horsepower), formerly used to denote engine over this data.
  • Page 348 General notes on the technical data Vehicle code Type plate The type plate is visible when the driver door is opened, on the lower part of the strut. Vehicles for certain export countries do not have a type plate. The manufacturer’s type plate contains the following data: Gross vehicle weight Maximum authorised weight of vehicle and trailer Maximum gross front axle weight...

  • Page 349: Data On Fuel Consumption

    General notes on the technical data Data on fuel consumption Note Actual consumption may vary from quoted test values, depending on Fuel consumption personal driving style, road and traffic conditions, the weather and the vehicle condition. The consumption and emission details shown on the vehicle data sticker differ from one vehicle to another.

  • Page 350: Towing A Trailer

    General notes on the technical data Towing a trailer Wheels Trailer weights Tyre pressure, snow chains, wheel bolts Trailer weight Tyre pressures The trailer weights and drawbar loads approved are selected in intensive The sticker with the tyre pressure values can be found on the inside of the trials according to precisely defined criteria.

  • Page 351: Technical Data

    Technical Data Technical Data Checking fluid levels Liquid coolant deposit Engine oil dipstick From time to time, the levels of the different fluids in the Oil filler neck vehicle must be checked. Never fill with incorrect fluids, Brake fluid reservoir Vehicle battery (underneath a cover) otherwise serious damage to the engine may be caused.

  • Page 352: Petrol Engine 1.4 110 Kw (150 Ps)

    Technical Data Petrol engine 1.4 110 kW (150 PS) Engine specifications Power output in kW (PS) 110 (150)/ 5800 Maximum torque in Nm at rpm 240/ 1500-4000 No. of cylinders/ capacity 4/ 1390 in cm Fuel 95 super RON Research-Octane-Number = Anti-detonation rating of the petrol. Performance figures Maximum speed in km/h...

  • Page 353: Diesel Engine 2.0 Tdi Cr 100 Kw (136 Ps)

    Technical Data Gross front axle weight in kg 1170/1220 1170/1220 Gross rear axle weight in kg 1070/1120 1260/1310 Permitted roof load in kg Trailer weight Trailer without brakes Trailer with brakes, gradients up to 8% 1800 Trailer with brakes, gradients up to 12% 1800 Engine oil capacity Approximate engine oil capacity with oil filter change...
  • Page 354 Technical Data Performance figures Maximum speed in km/h Acceleration from 0-80 km/h in seconds. Acceleration from 0-100 km/h in seconds. 11.1 Consumption (litres/100 km)/ CO (g/km) 5 seats 7 seats Urban cycle 6.8/179 6.9/182 Extra urban cycle 4.8/127 4.9/130 Combined 5.5/143 5.6/146 Weights...

  • Page 355: Diesel Engine 2.0 Tdi Cr 100 Kw (136 Ps) Automatic

    Technical Data Diesel engine 2.0 TDI CR 100 kW (136 PS) Automatic Engine specifications Power output in kW (PS) 100 (136)/ 4200 Maximum torque in Nm at rpm 320/1750-2500 No. of cylinders/ capacity 4/1968 in cm Fuel Min. 51 CN Cetane-Number (cetane index) = Measure of the combustion power of the diesel Performance figures Maximum speed...

  • Page 356: Diesel Engine 2.0 Tdi Cr 103 Kw (140 Ps)

    Technical Data Gross front axle weight in kg 1220/1270 1230/1280 Gross rear axle weight in kg 1100/1150 1260/1310 Permitted roof load in kg Trailer weight Trailer without brakes Trailer with brakes, gradients up to 8% 2200 Trailer with brakes, gradients up to 12% 2200 Engine oil capacity Approximate engine oil capacity with oil filter change...
  • Page 357 Technical Data Performance figures Maximum speed in km/h Acceleration from 0-80 km/h in seconds. Acceleration from 0-100 km/h in seconds. 10.9 Consumption (litres/100 km)/ CO (g/km) 5 seats 7 seats Urban cycle 6.8/179 6.9/182 Extra urban cycle 4.8/127 4.9/130 Combined 5.5/143 5.6/146 Weights...

  • Page 358: Diesel Engine 2.0 Tdi Cr 103 Kw (140 Ps) Automatic

    Technical Data Diesel engine 2.0 TDI CR 103 kW (140 PS) Automatic Engine specifications Power output in kW (PS) 103 (140)/ 4200 Maximum torque in Nm at rpm 320/1750-2500 No. of cylinders/ capacity 4/1968 in cm Fuel Min. 51 CN Cetane-Number (cetane index) = Measure of the combustion power of the diesel Performance figures Maximum speed...

  • Page 359: Diesel Engine 2.0 Tdi Cr 125 Kw (170 Ps) Automatic

    Technical Data Gross front axle weight in kg 1220/1270 1230/1280 Gross rear axle weight in kg 1100/1150 1260/1310 Permitted roof load in kg Trailer weight Trailer without brakes Trailer with brakes, gradients up to 8% 2200 Trailer with brakes, gradients up to 12% 2200 Engine oil capacity Approximate engine oil capacity with oil filter change...
  • Page 360 Technical Data Performance figures Maximum speed in km/h Acceleration from 0-80 km/h in seconds. Acceleration from 0-100 km/h in seconds. Consumption (litres/100 km)/ CO (g/km) Urban cycle 6.7/177 Extra urban cycle 5.4/143 Combined 5.9/154 Weights 5 seats 7 seats Gross vehicle weight in kg 2370 2540...

  • Page 361: Dimensions And Capacities

    Technical Data Dimensions and capacities Dimensions Length, width 4854 mm 1904 mm Height at kerb weight 1720 mm Front and rear projection Wheelbase 2920 mm Turning circle Front Rear Track width 1557 – 1569 mm 1605 – 1617 mm Capacities Fuel tank 70 l.

  • Page 363: Index

    Extended stay abroad with your vehicle . . 255 seat ......125 Alarm system .
  • Page 364 Index Anti-trap function Automatic car wash ..... . 243 Axle loads ......15 Electric windows .
  • Page 365 Index Emergency braking function ... . 191 Care Indicator ......328 Parking brake .
  • Page 366 Folding table ......150 Child seat ....... 40 Controls .
  • Page 367 Differential lock Convenience opening Dangers of not using the seat belt ... 19 See "Braking assist systems" ... 195 Electric windows ..... . 94 Dash panel .
  • Page 368 Index Doors ........84 Driving in winter Electric sockets Child safety lock .
  • Page 369 Rear assist ......214 Folding the backrest of the front passenger seat . . Engine oil ......280 Fault memory changing .
  • Page 370 Index Front passenger airbag G 12 plus-plus ......285 Deactivating using the key switch ..34 General overview of the engine compartment 349 See "Airbag system"...
  • Page 371 Transporting a load ....14 Integrated child seat ..... . 48 Seat belt routing .
  • Page 372 Index Main panel Opening Turn signal and main beam lever ..100 Doors ....... 84 Electric sliding door .
  • Page 373 Index Park Assist ......207 Particulate filter ......230 Brake operation .
  • Page 374 Reflective vest ......315 Seat belts ......16, 21 Running in Reflective vests .
  • Page 375 Spare fuel canister ..... . 265 seat ......125 Jump leads .
  • Page 376 Index Sunshade Start-Stop ......201 Tyre pressures ..... . . 298 Anti-trap function .
  • Page 377 Tyre monitoring systems ....220 seat ......125 Traction control when accelerating (TCS) .
  • Page 378 Treating your upholstery ....250 Cleaning seat belts ....253 Vehicle’s battery...
  • Page 379 Wheels and tyres ......294 Seat belts ......17 Windscreen heating .
  • Page 380 Index Winter Additional heater ....167 Menu configuration ....71 Winter driving Driving with a trailer .
  • Page 381 SEAT S.A. is permanently concerned about continuous development of its types and models. For this reason we ask you to understand, that at any given time, changes regarding shape, equipment and technique may take place on the car delivered. For this reason no right at all may derive based on the data, drawings and descriptions in this current handbook.

Table of Contents

Save PDF