Advertisement
Advertisement
Table of Contents
Related Manuals for ZKTeco X8-BT
Summary of Contents for ZKTeco X8-BT
- Page 1 User Manual X8-BT Version: 1.0 Date: August 2019...
-
Page 2: Device Installation
1. Device Installation Method 1: Install on the wall 1) Remove the screws from 2) Remove the back cover of 3) Fix the back cover on the wall. the bottom of the device. the device. (Drill the wiring hole and fixing holes according to the back cover) 4) Install the device on the fixed 5) Fix the device on the back... -
Page 3: Structure And Function
2. Structure and Function Access Control System Function: Door Sensor 1) When a registered user's identity is verified, the Lock access control device will send out signal to unlock the door. 2) The door sensor will detect the status of the lock. If the door is unexpectedly opened or improperly Exit Button closed, an alarm will be triggered. -
Page 4: Connection With Other Devices
I: device’s current output, U : lock voltage, I : lock current. LOCK LOCK 3) One device controls two locks 4) Two devices control one lock Access Control Device 1 Professional Access 门禁机1 Control Power 专 业门 禁电 源 NC Lock +12V 通... -
Page 5: Administrator Operation
Conventions Green: Success Password = 4 digits Light 【#】Confirm Digit Red: Failure User ID ≤5 digits Status 【*】Cancel Success: A long beep Hint Failure: Two short beeps tone Error: Four short beeps Note: After entering password/user ID, user must press 【 #】 to confirm; press 【 *】 to return to initial state. - Page 6 Changing Administrator Fingerprint Press new fingerprint Verify administrator Press【8】 three times fingerprint (The indicator turns (The indicator turns Press【*】+【#】 (The indicator turns green and makes a long green and makes a green and makes a beep) long beep) long beep) Press【*】to exit Lost Administrator Fingerprint If the administrator fingerprint is lost, please dismantle the device and wait 30 seconds when...
-
Page 7: User Authentication
Enter the group ID Verify administrator Press【*】+【#】 Press【3】 fingerprint. （Group IDs：1~8） Enter four digits password twice, end Press【*】to exit. with【#】each time Note: When a password is changed to 0000, the password is disabled. When a password is successfully changed, you can immediately change the next password by entering another group ID. - Page 8 12. Unlocking Duration Configuration (default duration: 6s) Enter the unlocking Verify administrator Press【*】+【#】 duration【#】 Press【4】 Enter the unlocking fingerprint (range：1s~10s） duration【#】 Press【4】 (range：1s~10s） Press【*】to exit Press【*】to exit Note: Values greater than 10 will be considered invalid. The indicator turns red and makes four short beeps.
-
Page 9: Alarm Configuration
NC (Normally Closed): The door sensor will send an alarm signal if it detects the door is open. Configure the door Verify administrator Press【*】+【#】 Press【0】+【5】 sensor mode【#】 fingerprint (0:NO 1:NC 2:NONE) Press【*】to exit 15. Alarm Configuration Note: If an alarm is triggered, when the door status is normal, it will be terminated after the user is authenticated;... - Page 10 Configuring Tamper Alarm Configure tamper Verify administrator Press【*】+【#】 alarm switch【#】 Press【7】 fingerprint (0:enable，1:disable) Press【*】to exit If this function is enabled, alarms will be raised when the device is dismantled from the wall. Configuring Door Sensor Delay (default value: 10s) When the door is not closed well after the set time period, the Door Sensor Alarm will generate an alarm signal to alert the users.
-
Page 11: Technical Specifications
Factory Defaults (Eight passwords for opening the door are set to 0 after reset) Parameters Type Defaults Unlocking Duration Verification Mode Fingerprint/Password/RF Card Door Sensor Type None Alarm Switch enable Administrator enable Authentication Alarm Tamper Alarm enable Door Sensor Delay Technical Specifications Fingerprint Collector SilkID Fingerprint Reader... - Page 12 ZK Building, Wuhe Road, Gangtou, Bantian, Buji Town, Longgang District, Shenzhen China 518129 Tel: +86 755-89602345 Fax: +86 755-89602394 www.zkteco.com Copyright©2019 ZKTECO CO., LTD. All rights reserved.
Need help?
Do you have a question about the X8-BT and is the answer not in the manual?
Questions and answers