Do you have a question about the EGO300 and is the answer not in the manual?
Questions and answers
Ralph wynne
February 5, 2025
Intermittent roller on off side could this be down to bushes
Summary of Contents for EGO EGO300
Page 1
User Manual REMOTE CARAVAN MOVER Installation guide and user information For use with Model Number: EGO300 Ref: EGO300-UM-1013-Rev.A...
Page 2
Package Contents (Fig.A) Cross Actuation Assembly (optional extra) Motor B Motor A SNAPPER PIN SNAPPER PIN...
Page 3
Parts Identification & Fitting Diagrams Fig.1 Fig.2 Fig.3 Fig.5 Fig.4 185mm (min) 2.8mm to 3.5mm 165mm 30mm to 45mm (min) 85mm (min) 1800mm to 2500mm (max) Fig.6 Fig.7 Caravan Floor L – Profile U – Profile...
Page 4
Parts Identification & Fitting Diagrams Fig.8 Fig.9 EM4445 10mm Fig.10 Fig.11 Fig.12 Overhead View Motor Motor Motor Motor...
Page 5
Parts Identification & Fitting Diagrams Fig.14 Fig.13 20mm Disengaged Position Fig.15 Engaged Position Fig.16 Caravan Front...
Page 6
Optional Fitting Adapters Additional chassis clamp adapters are available, as follows: Low Profile Chassis Adapter Plates (Part No. CM-029) If your chassis frame height is less than 140mm these plates must be fitted to lower the assembly to provide the correct height of 185mm. Drilling of your chassis may be required.
Introduction Thank you for choosing an Ego® caravan mover. This has been produced according to very high standards and has undergone careful quality control procedures. Simply by using the remote control you can move your caravan effortlessly into any position required within operating guidelines.
(Fig.2A) are 20mm away from the surface of the centre each tyre (Fig.14). Two 20mm spacers (23) are provided. It is vitally important that each roller is at exactly the same distance away from the tyre. The whole Ego® Page 3 Ref: EGO300-UM-1013-Rev.A...
Motor A Negative (-) cable to terminal 2 Motor B Positive (+) cable to terminal 2 Motor B Positive (+) cable to terminal 3 Motor B Negative (-) cable to terminal 1 Motor B Negative (-) cable to terminal 4 Ego® Page 4 Ref: EGO300-UM-1013-Rev.A...
You can then unwind the battery cable from the Carry Case and connect to your 12V battery power source. Caution! Make sure that you do not reverse the Positive (+) and Negative (-) connections. Incorrect connection (reverse polarity) may result in damage to the Control Unit. Ego® Page 5 Ref: EGO300-UM-1013-Rev.A...
Do not use the mover as a brake, when you have finished manoeuvring always engage the caravan’s handbrake. SAFETY FIRST! Ensure that there are no persons or obstructions in the vicinity of the caravan prior to testing. Ego® Page 6 Ref: EGO300-UM-1013-Rev.A...
Install only 2 of the 3 ‘AAA’ batteries into the battery compartment of the Handset (see Fig.5A). Press the Reset button (Fig.7A), the green LED will flash (press the reset button on both Control Units when using a full four-motor Quattro system). ® Ego® Page 7 Ref: EGO300-UM-1013-Rev.A...
Apply the handbrake first and then disengage the drive rollers from the tyres. Store remote control in a safe place (out of reach of children or other unauthorised people). Ego® Page 8 Ref: EGO300-UM-1013-Rev.A...
Make sure you keep it charged to ensure it is in good condition the next time you want to use Once a year have your Ego® caravan mover maintained and visually inspected. This inspection must include all the bolt/ nut connections, the cables and electrical connections and lubrication of movable parts/joints.
Page 16
If the pressure is low, the roller would need to be pushed into the tyre further than usual to gain sufficient traction. In case of any doubt, please call your Ego® Caravan Mover supplier. Ego®...
Need help?
Do you have a question about the EGO300 and is the answer not in the manual?
Questions and answers
Intermittent roller on off side could this be down to bushes