Table of Contents
Advertisement
Quick Links
Electric Hose Reel Kit
2005 and After Multi-Pro
Model No. 41135—Serial No. 310000001 and Up
Note: Determine the left and right sides of the machine from the normal operating position.
This attachment is a hose extended hand sprayer with an
electric reel intended to be used by professional, hired
operators in commercial applications. It is primarily
designed for spraying golf course applications, parks,
sports fields, and on commercial grounds. It is designed
to only be used in conjunction with machines designated
by the manufacturer.
This product complies with all relevant European
directives, for details please see the separate product
specific Declaration of Conformity (DOC) sheet.
Important: Teflon tape is required for the
installation of this kit. The tape is used to wrap
threads of fittings before assembly. Threads should
be wrapped starting at the base and traveling to the
tip of fitting to ensure a waterproof seal.
Important: A non-petroleum based lubricant, such
as vegetable oil, will be required for the installation
of this kit.
Note: If you are installing this kit on a sprayer with a
covered boom kit, you will need additional parts and
instructions; contact your Authorized Toro Distributor
for more information.
Read this manual carefully to learn how to operate and
maintain your product properly. The information in
this manual can help you and others avoid injury and
product damage. Although Toro designs and produces
safe products, you are responsible for operating the
product properly and safely.
You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a
dealer, or to register your product.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready. Figure 1
© 2009—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
1200/1250 Turf Sprayer
illustrates the location of the model and serial numbers
on the product.
1. Model and serial number plate
Model No.
Serial No.
Register at www.Toro.com.
Form No. 3364-446 Rev A
Installation Instructions
Figure 1
Original Instructions (EN)
Printed in the USA.
All Rights Reserved
Advertisement
Table of Contents
Related Manuals for Toro 41135
Summary of Contents for Toro 41135
- Page 1 Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 Register at www.Toro.com.
-
Page 2: Safety And Instructional Decals
Safety • Do not use the hand sprayer if there are any leaks in any hoses, fittings, or other components. Improper use or maintenance by the operator or • Do not spray near power lines. owner can result in injury. To reduce the potential •... -
Page 3: Installation
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Hose reel mount, left Hose reel mount, right Flange bolt (1/2 x 1-1/4 inches) Flange nut (1/2 inch) Hose reel mounting tubes Bolt (5/16 x 3-1/2 inch) Assemble the frame. -
Page 4: Preparing The Machine
on the boom frame so that it is in contact with the boom frame pin. Preparing the Machine No Parts Required Procedure 1. Ensure that the machine is empty of all fluids. If chemicals have been used in the machine, flush the system thoroughly with clean water;... - Page 5 3. Install the left hose reel support (support without the spray gun holder tube) to the vehicle frame using 2 U-bolts, spacer and 4 flange nuts (3/8 inch) as described in steps 1 and 2. Do not fully tighten the flange nuts to allow for later adjustment.
-
Page 6: Installing The Control Valve
Figure 6 1. Power wire from the 2. Solenoid electrical box on the hose reel. Figure 7 11. Connect the black wire to a post on the ground 1. Supply tee 3. Boom supply hose terminal block, located under the solenoid. 2. - Page 7 portion of the support bracket using two flange-head bolts (1/4 x 3/4 inch) and two flange nuts (1/4 inch). Figure 9 1. Control Valve 3. Boom supply hose Figure 11 2. Retaining fork, new 4. Retaining fork, existing 1. Control valve bracket 4.
- Page 8 the pressure gauge. Use a hex wrench to screw the previously (Figure 15). Tight the plastic nut to secure reducer assembly to the pressure gauge (Figure 13). the assembly to the valve. Figure 15 Figure 13 1. Pressure gauge assembly 3.
- Page 9 4. Connect the negative battery wire to the battery. 5. Press the hose wind button and carefully guide the hose onto the reel moving the hose from side to side to evenly distribute the hose. Connecting the Spray Hose CAUTION Parts needed for this procedure: Hands, loose clothing, long hair, and jewelry could get caught in the hose and reel while...
-
Page 10: Operation
Operation 4. At the operator’s position, turn the pump on. 5. Increase the engine speed until the pressure gauge reads the desired psi and engage the neutral engine WARNING speed lock. Fluid under pressure can penetrate skin and cause Important: Do not use a pressure setting injury. - Page 11 5. Return the engine to idle speed. 6. Stop the pump. Important: Ensure that you flush the spray gun with fresh clean water during your daily cleaning routine (refer to your sprayer Operator’s Manual ). Failure to properly clean the spray gun may degrade the performance and reliability of the hose reel kit and spray gun.