Sealey SFC4 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE
KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1 GENERAL SAFETY

WARNING! Ensure Health & Safety, local authority, and general
workshop practice regulations are adhered to when using this
cabinet.

WARNING! Use caution when handling and assembling the metal
components. The metal may have sharp edges or corners, the use
of protective gloves is recommended.

Locate the cabinet in an appropriate area for its purpose.

Keep the work area clean, uncluttered and ensure there is
adequate lighting.

Keep the cabinet clean and tidy in accordance with good office
practice.

Keep children and unauthorised persons away from the working area.

DO NOT climb, step or stand on the cabinet drawers.

DO NOT use the cabinet for any purpose other than that for
which it is designed.

DO NOT exceed the maximum 30kg weight allowance for each drawer.

DO NOT use in damp work areas.

WARNING! The warnings, cautions and instructions referred to in
this instruction manual cannot cover all possible conditions and
situations that may occur. It must be understood that common
sense and caution are factors which cannot be built into this product,
but must be applied by the operator.
2. INTRODUCTION & CONTENTS
2.1 Lockable filing cabinet, with individual drawer opening to prevent
tipping when loaded. Maximum capacity of 30kg per drawer. Each
drawer will accept foolscap or A4 suspension files.
Size (W x D x H): ..........................................452 x 620 x 1330mm
2.2 CONTENTS LIST
(A) Back panel (1)
(B) Side panel left (1)
(C) Side panel right (1)
(D) Top (1)
(E) Upper front cross piece (1)
(F) Lower front cross piece (1)
(G) Lock with lever (1)
(H) Cabinet side runners (8)
(J) Drawer base/sides (4)
3. ASSEMBLY
3.1 CABINET ASSEMBLY
Whilst the primary panels of this cabinet are held together with
screws, much of the construction relies on inter-connecting hooks
and slots. Once in place the panels are prevented from coming
apart by tabs which have been bent up out of the metal sheet and
clip into holes in the adjacent component. During transportation
some of these tabs may have closed up. With the exception of the
drawer and cabinet runners it is recommended to open all the tabs
up slightly using a flat bladed screwdriver in order to ensure that
all components clip together successfully.
3.2 ATTACH DRAWER RUNNERS TO CABINET SIDES (Fig.1)
3.2.1 Identify the eight drawer runners (H) that attach to the side panels.
These are wider than the runners that attach to the drawers. Sort
them into the 4 left hand runners that attach to the left hand panel
(B) and the 4 right hand runners that attach to the right hand
panel (C). Each runner has two hooks on the rear face which slot
into holes in the box sections attached to the inside of each panel.
The hook at the non-sliding end of each runner slides horizontally
into the hole at the back of the panel. Once fully inserted, the hook
at the other end of the runner will drop into the hole at the front of
the panel. Push down firmly on the front end of the runner to
engage the hook and the locking tab.
(K) Drawer front panels (4)
(L) Drawer front inner panel (4)
(M) Drawer backs (4)
(N) Drawer side runners (8)
(O) Right locking block (4)
(P) Left hand lock lift block (4)
(R) Self tapping screws
Cabinet screws, head Ø 11mm (12)
Drawer screws, head Ø 9 mm (34)
(S) A4 File Runners (2)
Original Language Version
INSTRUCTIONS FOR:
FILING CABINET 4 DRAWER
SFC4
MODEL No:
3.3 ATTACH LOCK TO CABINET TOP (D) (Fig.1)
3.3.1 Referring to DETAIL 1 in fig.1 insert the lock from the inside of the
front edge and fix it in place with two self tapping screws. (Ø9mm)
3.4 ATTACH SIDE PANELS (B) & (C) TO BACK PANEL (A).
3.4.1 Referring to DETAIL 2 in fig.1, interlock the back edge of side
panel (C) with the right hand edge of the back panel (A) and screw
the two panels together using four self tapping screws provided
(Ø11mm). Attach side panel (B) to the left hand side of the back
panel (A) in the same manner using four self tapping screws
(Ø11mm).
Fig.1
SFC4 Issue No: 1 - 22/02/10