Summary of Contents for StrongU Miner STU-U6
- Page 1 StrongU Miner STU - U6 Operating Instructions V1.1 Shenzhen StrongU Technology Co., Ltd. https://strongutech.com...
-
Page 2: Important Safety Information
Shenzhen StrongU Technology Co., Ltd. Important Safety Information The miner produces a lot of heat during operation. Please follow the requirements below: 1. Prevent the body from direct contact to avoid burns; 2. Keep the product at the appropriate temperature and humidity and in a ventilated place: Control the temperature to the range of 0-40℃... -
Page 3: Packing List
1 power cable The control panel, power supply and hash board are integrated in the StrongU miner. The wires of all parts have been connected in the factory, so the user only needs to connect the network cable and the power cable. -
Page 4: Product Overview
Shenzhen StrongU Technology Co., Ltd. Product overview Basic structure: 1. Chassis: including main components such as hash board 2. Power supply: digital switching power supply module 3. Control board: hash control module 4. Fan: forced heat dissipation module Controller panel: 1. - Page 5 Shenzhen StrongU Technology Co., Ltd. Controller interfaces: 1. Data cable of hash board 1 2. Data cable of hash board 2 3. Fan 1 4. Fan 2 5. Power cable of control panel 5/13...
-
Page 6: Cable Connection
Shenzhen StrongU Technology Co., Ltd. Network environment requirements This product only supports the cabled access to network through RJ45 interface. It does not support the POE (Power Over Ethernet) power supply router (switch). The DHCP service of the router (switch) must be enabled. - Page 7 Shenzhen StrongU Technology Co., Ltd. Miner IP detection 1. Prepare a computer equipped with the windows system, and install the ip reporter. ipreporter installation 1.Visit the link https://strongutech.com/stu_IP_Reporter_V1.1, and download the installation package. 2. Decompress and run it. 2. Connect the computer and miner into the LAN within the same segment.
-
Page 8: Network Configuration
Shenzhen StrongU Technology Co., Ltd. Network configuration 1. Start the browser in the PC (recommendation: CHROME/IE/FIREFOX). 2. Enter the IP obtained by the Ip reporter in the previous step into the browser address bar, similar to “192.168.xx.xx”. Fill in the username and password and press “Enter”. - Page 9 Shenzhen StrongU Technology Co., Ltd. 4. Perform one of the following two operations: 1) Accept the default dynamic ip configuration (recommended), and directly click Miner Configuration in the header to enter the Pool Configuration page. 2) Set the static ip configuration. Click Setting in the lower right corner or NetWork in the header to change network configuration.
-
Page 10: Pool Configuration
You can click “Cryptocurrencies” in the drop-down menu of the upper right corner to switch the currency. The StrongU STU-U6 miner supports at most three pools for each currency. If the current pool is not available, next available pool will be connected automatically according to the priority order. - Page 11 3. Click “Save&Apply” in the lower right corner. The miner will run with new currency parameters. Status inspection The StrongU miner monitor provide the following data: 6. Summary Operating time/real-time hash/average hash/number of blocks identified/number of local tasks/number of completed shares/cumulative difficulty/maximum difficulty/speed of fan 1/speed of fan 2, etc.
- Page 12 Shenzhen StrongU Technology Co., Ltd. 12/13...
- Page 13 Shenzhen StrongU Technology Co., Ltd. Room508, Saixi Science&Technology Mansion, 3398 Binhai Avenue, Nanshan district, Shenzhen, China. https://strongutech.com 13/13...
Need help?
Do you have a question about the Miner STU-U6 and is the answer not in the manual?
Questions and answers