Toro Wheel Horse 79375 Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn and Garden Equipment
  5. Wheel Horse 79375
  6. Operator's manual
Toro Wheel Horse 79375 Operator's Manual

Toro Wheel Horse 79375 Operator's Manual

36” tiller for 5xi lawn and garden tractors
Hide thumbs
Table of Contents

Advertisement

Quick Links

FORM NO. 3322–850
Wheel Horse
36" Tiller
for
5xi Lawn and Garden Tractors
Model No. 79375 – 8900001 & Up
Operator's Manual
IMPORTANT: Read this manual, and your tractor manual, carefully. They
contain information about your safety and the safety of others. Also
become familiar with the controls and their proper use before you operate
the product.

Advertisement

Table of Contents
loading

Related Manuals for Toro Wheel Horse 79375

Summary of Contents for Toro Wheel Horse 79375

  • Page 1 FORM NO. 3322–850 Wheel Horse 36” Tiller 5xi Lawn and Garden Tractors Model No. 79375 – 8900001 & Up Operator’s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information about your safety and the safety of others. Also become familiar with the controls and their proper use before you operate the product.
  • Page 2 Introduction We want you to be completely satisfied with your The warning system in this manual identifies new product, so feel free to contact your local potential hazards and has special safety messages that Authorized Service Dealer for help with service, help you and others avoid personal injury, even death.

  • Page 3: Table Of Contents

    Contents Page Page Maintenance ......Safety and Instruction Decals ....Service Interval Chart .

  • Page 4: Safety And Instruction Decals

    Safety Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. ON TINE SHIELD LEFT and RIGHT SIDE (Part No. 92–7112) ON PULLEY BOX (Part No.

  • Page 5: Installation

    Installation Loose Parts Note: A rear–mount Attach–A–Matic , which must be purchased separately, is required for this tiller. Use the chart below to identify other parts used for assembly. DESCRIPTION QTY. Tiller housing Tiller lift frame Assemble the tiller Panel guard Cotter pin 1/8”...

  • Page 6: Assembling The Tiller

    Installation Assembling the Tiller Support the tiller housing so it sets in an upright position. Remove the 3/8 x 5–1/2” (140 mm) bolt, 3/8 x 4–1/2” (114 mm) bolt, and (2) 3/8” locknuts; discard the 1/2” nuts (used as spacers for shipping).

  • Page 7: Tractor Set-Up

    Installation Install the ilder pulley on the 3/8–16 x 2” (51 Installing the Front Pulley Box to the mm) bolt so that the extended hub of the pulley Tractor is toward the tiller lift frame. Route the belt Attach the pulley box that came with the tiller to under the idler pulley, and insert the bolt through the front Attach–A–Matic .
  • Page 8 Installation 2314 Figure 6 m–3433 1. Snap ring 3. Drawbar Figure 7 2. Pin 4. Spacer (2) 1. Clevis pin 3/8” x 1” (25 2. Hairpin cotter Preparing the Tractor’s Attachment Lift These pins must be installed when operating with a blade, snowthrower, or tiller attachment.
  • Page 9 Installation Remove the Rear Transaxle Cover Remove the transaxle cover from the back of the tractor (Fig. 8). POTENTIAL HAZARD Rotating shaft or cooling fan can cause Remove the two bolts and locknuts securing the injury. transaxle cover to the tractor frame. WHAT CAN HAPPEN Fingers, hands, feet, hair, etc.

  • Page 10: Installing The Tiller To The Tractor

    Installation Replace the drive shaft maintenance cover (if removed). m–3491 Figure 10 1. Tiller 6. Tiller hitch bar 2. Jack shaft assembly 7. Smaller jack shaft bar 3. Lift cable 8. Jack shaft/PTO drive belt pulley 4. Tiller belt (short belt) 9.
  • Page 11 Installation Open the latches on the mid Attach–A–Matic . Install the larger bar at the other end of the jack shaft assembly to the mid Attach–A–Matic . Then turn the lever of the Attach–A–Matic counterclockwise to lock the jack shaft assembly to the tractor (Fig.
  • Page 12 Installation m–3503 Figure 15 1. Lift cable 4. Washer m–3504 2. Trunnion 5. Hairpin cotter Figure 14 3. Locknut 1. Lift cable 4. Clevis pin 5/16” x 1” (25 2. Clevis 5. Hairpin cotter 12. Secure the lift cable to the trunnion with a 3.
  • Page 13 Installation 16. Position the end of the PTO belt (long belt) into C. If the tension indicators are not in the same the groove of the engine PTO pulley (Fig. 16), position on both the left and right sides, making sure it is also under the pulleys in the release the belt tension, turn the adjustment pulley box.

  • Page 14: Removing The Tiller

    Installation Removing the Tiller Note: Save all hardware, washers and hairpin cotters for use when installing tiller. Park the tractor on a level surface with enough space in front of it to disengage from the tiller. Lower the attachment lift, set the parking brake, and turn the ignition key to “STOP”...
  • Page 15 Installation Press the release button and open the rear latches of the rear Attach–A–Matic . Remove the tiller hitch bar (Fig. 21). m–3501 Figure 21 1. Smaller jack shaft bar 3. Rear Attach–A–Matic 2. Tiller hitch bar 4. Rear Press the release button on the mid Attach–A–Matic and turn the lever clockwise to open the latches (Fig.

  • Page 16: Operation

    Operation POTENTIAL HAZARD Contact with rotating tines may cause injury. WHAT CAN HAPPEN Rotating tines can cut hands, feet or other body parts. HOW TO AVOID THE HAZARD Keep away from the rotating tines while operating the tiller. m–3258 Keep your hands, feet, and any other part Figure 23 of your body or clothing away from 1.

  • Page 17: Lowering Attachments

    Operation Lowering Attachments Tips for Tilling Clean area of trash, branches and rocks before tilling Start the tractor. to prevent equipment damage. Push the lift lever DOWN to lower the Always begin tilling with the slowest ground speed attachment (Fig. 24). possible.

  • Page 18: Maintenance

    Maintenance Service Interval Chart Each Storage Fall Service Operation Notes Hours Hours Service Service Oil–check level Belt tension–check initial Belt–check for wear/cracks Chipped surfaces–paint POTENTIAL HAZARD If you leave the key in the ignition switch, someone could start the engine. WHAT CAN HAPPEN Accidental starting of the engine could seriously injure you or other bystanders.

  • Page 19: Greasing And Lubrication

    Maintenance Greasing and Lubrication Service Interval/Specification Check the gear lubrication level in the gear case after every 25 operating hours or once a year, whichever occurs first. Gear lubrication changes are not required. Gear lube type: SAE 90-140 API service GL-4 or GL-5.

  • Page 20: Checking Pto Drive Belt Tension

    Maintenance m–3491 Figure 26 1. Spring loaded idler arm 3. Jack shaft pulley 2. Tiller drive belt (short belt) Remove the belt guard from the gear box and ilder mounting (Fig. 27). m–4422 Remove the belt and replace with a new one. Figure 27 1.

  • Page 21: Storage

    Maintenance m–3643 Figure 28 1. Belt tension indicator (2) 3. Seating position for belt tension release arm 2. Belt tension adjustment knob 4. Belt tension released Storage Before long term storage wash the machine with mild detergent and water to remove dirt and grime from the entire machine.

Table of Contents