Wayne-Dalton 9700 Manual
  1. Manuals
  2. Brands
  3. Wayne-Dalton Manuals
  4. Garage Door Opener
  5. 9700
  6. Manual
Wayne-Dalton 9700 Manual

Wayne-Dalton 9700 Manual

Hide thumbs Also See for 9700:
Table of Contents

Advertisement

Quick Links

Models 9700 and
9510
T
o r s i o n
r
l
esidenTial and
ighT
s
l
Tandard
ifT
w
indload
i
i
nsTallaTion
nsTrucTions
M
anual
DEFINITION OF LIGHT COMMERCIAL:
1. Door Heights less than or equal to 8'0" (< = 8'0") are considered
Residential Applications.
2. Door Heights greater than 8'0" (> 8'0") are considered Light
Commercial Applications.
PLEASE DO NOT RETURN THIS PRODUCT
TO THE STORE
If you need assistance, please call 1-866-
569-3799 (press Option 1) and follow the
prompts to contact a customer service
representative. They will be happy to handle
any questions that you may have.
©Copyright 2020
Wayne Dalton, a division of Overhead Door Corporation
c
oMMercial
a
o
'
nd
wner
s
T a b l e O f C o n t e n t s
IMPORTANT NOTICES!
To avoid possible injury, read and fully understand the enclosed
instructions carefully before installing and operating the garage door. Pay
close attention to all warnings and notes. After installation is complete,
fasten this manual near garage door for easy reference.
This Installation document is available at no charge from:
- Your local Wayne Dalton Sales Center, or
- Online at www.Wayne-Dalton.com, or
- By mailing to: Wayne Dalton, a division of Overhead Door Corporation, P.O. Box
67, Mt. Hope, OH., 44660
Part Number
350276
2
2
2
3
4
4
6
7
12
18
18
18
18
19
19
19
19
19
21
REV9_01/17/2020

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 9700 and is the answer not in the manual?

Questions and answers

Related Manuals for Wayne-Dalton 9700

Summary of Contents for Wayne-Dalton 9700

  • Page 1: Table Of Contents

    This Installation document is available at no charge from: - Your local Wayne Dalton Sales Center, or - Online at www.Wayne-Dalton.com, or - By mailing to: Wayne Dalton, a division of Overhead Door Corporation, P.O. Box 67, Mt. Hope, OH., 44660...

  • Page 2: Pre-Installation

    Existing Door & Prepar- ensure door operates freely. ing the Opening. These are available for download at www.Wayne-Dalton.com or at your 15. Test electric opener’s safety features monthly, following opener manufacturer’s instruc- local Wayne Dalton Sales Center.

  • Page 3: Package Contents

    NOTE: Drill a 3/16” pilot hole in the mounting surface to avoid splitting the lumber. Do not attach the mounting surface with nails. Package Contents WEATHERSTRIPS (MAY NOT BE INCLUDED): Depending on the size of your door, you may have to cut or trim the weatherstrips (if neces- NOTE: Depending on the door model, some parts listed will not be supplied if not required.

  • Page 4: Door Section Identification

    The INTERMEDIATE SECTION II can be identified by #4 graduated end hinges. The INTERMEDIATE SECTION III can be identified by #5 graduated end hinges. The INTERMEDIATE SECTION IV can be identified by #6 graduated end hinges. The TOP SECTION can be identified with no pre-installed graduated end or center hinges. Center bracket Keys bushing...
  • Page 5 Vise clamps Hammer Step ladder Leather gloves Pencil Approved winding bars Saw horses Safety glasses Locking pliers...

  • Page 6: Breakdown Of Parts

    BREAKDOWN OF PARTS NOTE: The illustrations shown on this page are J11. general representations of the door parts. Each specific door models may have unique variations. J11. J10. J11. J12. J11. J10. Top of vertical Top of vertical track track B2.

  • Page 7: Door Installation Instructions

    DOOR INSTALLATION Horizontal INSTRUCTIONS track 12” Or 15” Radius Before installing your door, be certain that you have read and followed all of the instruc- 15” Radius track 12” Radius track tions covered in the pre-installation section of this manual. Failure to do so may result in an (2) 1/4”- 20 x 9/16”...
  • Page 8 Left hand NOTE: Measure the length of the vertical tracks. vertical track Using the Jamb Bracket Schedule (shown on the Attaching Strut(s) To Section Windload Specification Sheet included in the hardware box), determine the placement of the Typical left hand windload jamb brackets for your door height.
  • Page 9 NOTE: Refer to the Windload Specification Sheet Center to determine if more fasteners are required to hinge(s) secure the strut to the section, as shown. Graduated Flag end hinge angle Typical strut Vertical 5/16” x 1-5/8” track Lag screws assembly Jamb 12R FA Or 15R FA 12R QI...
  • Page 10 NOTE: Larger doors with double graduated end hinges, fasten both hinges to connect the Top section NOTE: Refer to the Windload Specification sections using 1/4” - 14 x 5/8” self-tapping screws. Sheet to determine if a pushnut is required to be installed on each short Strut Repeat same process for other sections, except top section.
  • Page 11 end over the top track roller of the top section. Align key slot of the horizontal track with the Quick Install tab of the flag angle. Push curved portion of horizontal track down to lock in place. Top section Horizontal track angle Top section Quick Quick...

  • Page 12: Counterbalance Installation Instructions

    - 18 nut to secure the slide to the top fixture. Repeat for other side. Next, lock each of the Left hand top fixture slides into place using (1) 1/4” - 20 x 9/16” track bolt and (1) 1/4” - 20 hex nut end bracket through any two aligning holes.
  • Page 13 Mounting surface Center bracket Mounting Vertical NOTE: Layout bushing assembly (3” Minimum) surface line counterbalance parts in (3” Minimum) proper orientation, then 5/16” x 1-5/8” Hex head 5/16” x 1-5/8” Hex head install onto torsion lag screws (RED HEAD) lag screws (RED HEAD) shaft, as shown.
  • Page 14 NOTE: Refer to Package Contents / Breakdown of Parts, to determine if your door came with NOTE: Layout Right hand cable a coupler assembly. counterbalance parts in drum, black proper orientation, then IMPORTANT: THE SPRING WARNING TAG(S) SUPPLIED MUST BE SECURELY ATTACHED install onto torsion TO THE STATIONARY SPRING CONE(S) IN PLAIN VIEW.
  • Page 15 torque (once set screws contact the shaft, tighten screws one full turn). NOTE: If you have torsion keyed shaft(s), insert (1) key into the slot of both the cable drum Securing Door for Spring Winding and the slot in the torsion keyed shaft, as shown. Rotate the left hand drum and torsion shaft until counterbalance lift cable is taut.
  • Page 16 NOTE: If rear back hangs are to be installed over drywall, use (2) 5/16” x 2” hex head lag 2. Maintaining a tight grip on the winding rod rotate it slowly in the proper direction, as shown below. screws and make sure lag screws engage into solid structural lumber. 3.
  • Page 17 NOTE: Door not shown for clarity. Header Jamb Jamb Nail Nail Weather Weather seal Jamb seal installed Balancing Door Remove locking pliers. Lift door and check its balance. Adjustments to the required number of spring turns stated may be necessary. If door rises off floor more than 2 ft. under spring tension alone, reduce spring tension.

  • Page 18: Optional Installation

    Optional Installation Door Arm Hookup Align hole in the door arm with holes in drawbar operator bracket tabs, as shown. Insert 5/16” x 1-1/4” clevis pin, making sure hole in clevis pin is outside of second tab of drawbar operator bracket. Insert hairpin cotter into clevis pin hole and spread hairpin cotter to secure assembly, as shown.

  • Page 19: Maintenance

    Wayne Dalton, a division of Overhead Door Corporation, P.O. Box direct exposure to sunlight. 67, Mt. Hope, OH., 44660, or at www.Wayne-Dalton.com. For additional information on garage door / operator maintenance go to www.dasma.com and reference TDS 151, 167 Cleaning the door will generally restore the appearance of the finish.
  • Page 20 Division of Overhead Door Corp. bracket label IMPORTANT! WHEN CONNECTING A TROLLEY TYPE GARAGE DOOR OPENER TO THIS DOOR, A WAYNE-DALTON OPENER/TROLLEY BRACKET MUST BE SECURELY ATTACHED TO THE TOP SECTION OF THE DOOR, ALONG WITH ANY U-BARS PROVIDED WITH THE DOOR. THE INSTALLATION OF THE OPENER MUST BE ACCORDING TO MANUFACTURER’S INSTRUCTIONS AND FORCE SETTINGS...

  • Page 21: Warranty

    Models 9700 and 9510 Wayne Dalton, a division of Overhead Door Corporation (“Seller”) warrants to the original purchaser of the Models 9700 and 9510 (“Product”), subject to all of the terms and conditions hereof, that the Product and all components thereof will be free from defects in materials and workmanship for the following period(s) of time,...
  • Page 22 Thank you for your purchase. PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE If you need assistance, please call 1-866-569-3799 (press Option 1) and follow the prompts to contact a customer service representative. They will be happy to handle any questions that you may have.

This manual is also suitable for:

9510

Table of Contents