Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Hyundai power products HYTR2600X
Summary of Contents for Hyundai power products HYTR2600X
- Page 1 GRASS TRIMMER HYTR2600X Instruction Manual...
- Page 2 We would be delighted if you left us positive feedback! Thank you for purchasing this product. This manual has been produced by Hyundai Power Products and should be kept with the product. Please read and understand these instructions before you use your product. Failure to do this may result in personal injury or damage to the product.
-
Page 3: Table Of Contents
Contents Features........................4-5 What’s In The Box......................5 General Safety......................6-9 For Safe Operation....................10-12 Symbols On The Machine..................13 Assembly........................14 Starting / Stopping Procedure..................15 Using The Trimmer....................16 Maintenance & Care....................18-21 Troubleshooting....................22-24 Specification......................25 Disposal........................26 Our Product Range....................27 Useful Information.....................28 Notes.........................29 Contact Us........................30 Declaration Of Conformity..................31 IMPORTANT: DON’T FORGET TO REGISTER YOUR EXTENDED 3 YEAR HYUNDAI WARRANTY WITHIN 30 DAYS OF PURCHASE. -
Page 4: Features
Features 1 - Nylon Cutter Head Contains replaceable nylon trimming line that advances when the trimmer head is tapped against the ground while the head is turning at normal operating speed. 2 - Cut-Off Knife Trims nylon line to the correct length- 180mm/ 7” from the head to end of line. If trimmer is operated without a cut-off knife the line may become too long (more than 180mm/7”) this will cause additional strain and may overheat or damage the engine. -
Page 5: What's In The Box
Features 7 - Safety Lever Before using the throttle, push safety lever down. 8 - Throttle Trigger Spring loaded to return to idle when released. When accelerating, press trigger gradually for best operating technique. Do not hold trigger while starting. 9 - Bulb Pushing bulb (7 to 10 times before starting),will remove all air and sale fuel from fuel system and bring fresh fuel to the carburetor. -
Page 6: General Safety
General Safety WARNING : READ THE INSTRUCTION BOOKLET THOROUGHLY BEFORE USING THE MACHINE. Keep for future reference and pass it on if the machine is loaned or sold to another user. Training carried out. The operator or user must take all necessary precautions to ensure their own safety and that of others, especially on slopes DANGER... - Page 7 General Safety machine away from the area of spilled fuel and Lack of maintenance will have a significant avoid creating any source of ignition until the influence on noise emissions and vibrations. fuel has evaporated and fuel vapours have It is necessary to take preventive steps to dissipated.
- Page 8 General Safety General Fuel Safety Electrical Safety (Where Applicable) CAUTION! ALL FUELS ARE FLAMMABLE • Electricity can kill – NEVER work on LIVE/ENERGISED equipment. • Fire hazard - keep fuel away from all sources of ignition for example heaters, • Prior to carrying out any maintenance work lamps, sparks from grinding or welding.
- Page 9 General Safety You must advise the medical staff of the type • Not all factors that lead to white finger of acid. disease are known, but cold weather, smoking and other diseases that affect blood vessels • Lead/acid battery = dilute sulphuric acid. and blood circulation as well as large and long-lasting impact of shocks are considered •...
-
Page 10: For Safe Operation
For Safe Operation 2. You must only work in daylight or with good During Use artificial light in good visibility conditions. Keep people, children and animals away from the 1. Never operate the engine in a confined working area. space where dangerous carbon monoxide fumes can develop. - Page 11 For Safe Operation repairs before using it again. 38. Pay attention to loosening and overheating of parts. If there is any 29. WARNING - If something breaks or an abnormality of the machine, stop operation accident happens whilst working, you must immediately and check the machine carefully.
- Page 12 For Safe Operation Intended Use Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in The machine is intended for trimming grass, connection with the tool’s construction and This machine may not be used to do other design: thing out of the described scope.
-
Page 13: Symbols On The Machine
Symbols On The Machine CAUTION! CE SYMBOL This product complies with the Handle carefully. applicable European directives and an evaluation method of conformity for these directives was done. INSTRUCTION MANUAL Read and understand operator’s manual before using the machine. WARNING! Never modify a Failure to follow instructions could trimmer in any way. -
Page 14: Assembly
Assembly Getting Started 2. Tighten adjustment knob securely. Debris Shield CAUTION - This guide is meant to serve as a quick reference for operating your Shield Fits snug on shaft. Some force may be HYUNDAI machine. We always advise reading required. -
Page 15: Starting / Stopping Procedure
Starting / Stopping Procedure Before Each Use STEP 5 Push the choke lever to ‘RUN’ position. (If • Always ensure that the trimmer is in a safe fitted with an automatic choke, squeezing the working condition. Inspect the machine, check throttle will reset the choke to ‘RUN’). -
Page 16: Using The Trimmer
Using The Trimmer Cutting WIth Nylon Head WARNING! Tilting the head to the wrong side will shoot the debris TOWARDS you. If the line head is For nearly all cutting, it is good to position the held flat to the ground so that cutting line head so that contact is made on the part occurs on the whole line circle, debris will be of the cutting area where the line is moving... - Page 17 Using The Trimmer Trimming This is feeding the trimmer carefully into the material you wish to cut. Tilt the head slowly to direct debris away from you. If cutting up to a barrier such as fence, wall or tree, approach from an angle where any debris ricocheting off the barrier will fly away from you, Move the line head slowly until the grass is cut right up...
-
Page 18: Maintenance & Care
Maintenance & Care Safety 8. If any warning message stickers or instruction is damaged, replace them. 1. WARNING - Before cleaning or doing 9. Store the machine in a safe place, out of the maintenance work, you need to disconnect reach of children. - Page 19 Maintenance & Care CAUTION - DO NOT use a hose pipe or pressure washer to clean the engine. Water can damage the engine or contaminate the fuel system. Air Filter 0.6 - 0.7mm (0.023” - 0.028”in.) Accumulated dust in the air filter will reduce engine efficiency.
- Page 20 Maintenance & Care Fuel & Oil Mixture CAUTION - ALL FUELS ARE FLAMMABLE Unleaded NOTE - All machines are tested and inspected Petrol so there may be some residual oil left in the machine so please fill with caution. • ALWAYS fuel and defuel in a well ventilated Fuel mixture at the rate other than 40:1 may area outside of buildings.
- Page 21 Maintenance & Care Cleaning 2. With the machine drained of all fluids, follow the cleaning instructions as set out in the pre- vious section. CAUTION - DO NOT use a hose pipe or pressure washer to clean the engine. Water 3.
-
Page 22: Troubleshooting
Troubleshooting Failure To Start Problem Possible Cause Possible Solution Fuel system 1. There is no fuel 1. Add fuel in tank abnormality in tank 2. Clean fuel filter 2. Fuel filter obstruct Spark plug Fuel system 1. Fuel is too dirty 1. - Page 23 Troubleshooting Failures such as difficulty in starting engine, irregularity in functions and abnormality in performance can normally be prevented if careful attention is paid to all operating instructions and maintenance procedures. Failure to start: - Dispose of fuel in the tank. - Insure that fuel is fresh and clean.
- Page 24 Troubleshooting Engine Running Unstable Problem Possible Cause Possible Solution Metal knocking sound Piston, piston rings, cylinder Replace piston, piston rings, worn cylinder Replace bearings Crank bearings worn. Metal knocking sound Engine overheats Replace fuel with correct mixture of unleaded petrol and semi-synthetic 2-stroke oil at 40:1 ratio.
-
Page 25: Specification
Specifications Main Unit Specifications Remote type Direct Drive; flexible curved shaft Maximum speed of trimmer shaft 9000/9000 /engine speed (rpm) Idle speed (rpm) 3000 Vibration values at each handle (m/s2) Sound pressure values [dB(A)] Sound power values [dB(A)] Guaranteed Sound power values [dB(A)] Line Max. -
Page 26: Disposal
Disposal or at your local Civic Amenity Site. Environmental Protection Under NO circumstances must any fuel or oil 1. Environmental protection should be a be put down any drains. priority of considerable importance when using the machine, for the benefit of both Certain products contain WEEE waste which social coexistence and the environment in should not be disposed of in your domestic... -
Page 27: Our Product Range
Our Product Range Generators Mini Dumpers Leisure Inverter, Petrol, Diesel And Built-In 4-Wheel Drive Mini Dumper / Power Barrow Motorhome Generators Yard Sweeper Pressure Washers Self Propelled Yard Sweeper Power Brush Petrol, Diesel And Electric Pressure Washers Water Pumps Scarifiers Submersible, Clean And Dirty Water And Petrol Lawn Scarifier And Aerator Professional Chemical Water Pumps... -
Page 28: Useful Information
Register your 3 year warranty within 30 days of purchase at: To leave a review, please go to: www.hyundaipowerequipment.co.uk/warranty uk.trustpilot.com/review/hyundaipowerequipment.co.uk Full warranty terms and conditions can be found on the HYUNDAI POWER PRODUCTS Ordering Spare Parts website: www.hyundaipowerproducts.co.uk Only use original spare parts: The Manual Updates... -
Page 29: Notes
Notes... -
Page 30: Contact Us
Need Help? Talk To Our Experts Contact Us Our friendly aftersales team will be more than happy to help you. Phone Call our team on 01646 687880, open Monday-Friday 8.30am-5pm. Email aftersales@hyundaipowerproducts.co.uk Online Live Chat Go to www.hyundaipowerproducts.co.uk Live chat is open Monday-Friday from 8.30am-5pm. Post Genpower Limited, Isaac Way, Pembroke Dock, Pembrokeshire, SA72 4RW, UK. -
Page 31: Declaration Of Conformity
Grass Trimmer 25.4cc 95dB(A) 106dB(A) 0.65kW Product Details Brand: Hyundai Model: HYTR2600X Description: Petrol grass trimmer. Name and address of technical documentation holder and EU distributor: Genpower Ltd, Isaac Way, Pembroke Dock, Pembrokeshire, SA72 4RW, UK. Signed by: Roland Llewellin, Managing Director... - Page 32 Importer: GENPOWER LTD Isaac Way, London Road, Pembroke Dock, UNITED KINGDOM, SA72 4RW T: +44 (0) 1646 687 880 F: +44 (0) 1646 686 198 E: info@hyundaipowerproducts.co.uk www.hyundaipowerproducts.co.uk Imported/Distributed by Genpower Ltd for The United Kingdom & Ireland Licensed by Hyundai Corporation, Korea...
Need help?
Do you have a question about the HYTR2600X and is the answer not in the manual?
Questions and answers
Trimmer cuts out when idling
The Hyundai HYTR2600X trimmer may cut out when idling due to the following reasons:
- There is water in the fuel, which requires replacing the fuel.
- The spark gap is incorrect and needs adjustment to 0.6-0.7mm.
- The coil gap is incorrect and should be adjusted to 0.3-0.4mm.
This answer is automatically generated
my strimmer is brand new but wont strim when i want it to
The Hyundai HYTR2600X strimmer may not work properly due to several possible reasons:
1. Improper Starting Procedure – If the switch is not moved to the ‘STOP’ position and the starter handle is not pulled correctly, the engine may not start.
2. Incorrect Cutting Technique – Tilting the nylon head incorrectly may cause debris to be thrown towards the operator, slow the engine, and waste the cutting line.
3. Use of Incorrect Line – Using wire or wire-reinforced line instead of the recommended 2mm nylon trimmer line can cause malfunctions.
4. Missing or Improperly Installed Debris Shield – The shield must be in place for proper operation and safety.
5. Lack of Maintenance – Failure to check for fuel or oil leaks, clean the machine, or perform routine maintenance can lead to performance issues.
6. Safety Interference – The electromagnetic field generated by the strimmer may interfere with medical implants, requiring caution.
7. Thrown Objects Risk – If operated near unprotected people, the strimmer should be used at low throttle to reduce the risk of thrown objects.
Checking these factors can help diagnose and resolve issues with the strimmer.
This answer is automatically generated
my strimmer wont strim
The Hyundai HYTR2600X strimmer may not work due to several possible reasons:
1. Engine Not Starting – Ensure the switch is in the correct position and follow the starting steps, including pulling the starter handle until the engine attempts to start.
2. Incorrect Cutting Line – Use only 2mm diameter, 3m length nylon monofilament line. Using wire or other materials can cause malfunction.
3. Debris Shield Missing – The proper debris shield must be in place for safe and effective operation.
4. Fuel Issues – Check if there is enough fuel and if it is properly mixed (since it is a 2-stroke engine).
5. Clogged or Worn Components – Inspect the air filter, fuel filter, and spark plug for dirt or damage.
6. Throttle Issues – If operating near people, using a low throttle speed may reduce performance.
7. Safety Features Engaged – Some built-in safety features may prevent operation if certain conditions are not met.
If none of these resolve the issue, further inspection or maintenance may be required.
This answer is automatically generated