Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
PLEASE ENSURE THAT INSTRUCTIONS ARE UNDERSTOOD PRIOR TO FITMENT
PLACE THESE INSTRUCTIONS IN THE VEHICLE'S GLOVEBOX AFTER INSTALLATION IS COMPLETED
Towbar Installation Instructions
HONDA ODYSSEY 5
Part Number
ECU: 04836
Tail Length: 1200mm
RPA Disable: N/A
Electric brake input location: Near ECU
Hayman Reese (Cequent)
PO Box 4050, Dandenong South VIC 3164
Phone 1800 812 017 Email info@haymanreese.com.au
Rev: A
HAYMAN REESE
PART No:
HONDA ODYSSEY 5
GEN CL2
TH
03243W
Page 1
03243W
TH
GEN CL2
Installation Time: Approx
Towbar capacity
Max Towing Braked
Max Towing Unbraked
Max Static Ball Load
145
Mins
1000
kg
450
kg
50
kg
Issue Date:
20-09-2018
Advertisement
Related Manuals for Hayman Reese 03243W
Summary of Contents for Hayman Reese 03243W
- Page 1 Max Static Ball Load ECU: 04836 Tail Length: 1200mm RPA Disable: N/A Electric brake input location: Near ECU Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: A Page 1 Issue Date:...
- Page 2 The high tensile fasteners supplied with this product were used to achieve the specified rating. If replacement is required ensure that fasteners of the same rating & quality are used. Contact an authorised Hayman Reese dealer if further information is required.
- Page 3 INSTALLATION INSTRUCTIONS PLEASE ENSURE THAT INSTRUCTIONS ARE UNDERSTOOD PRIOR TO FITMENT PLACE THESE INSTRUCTIONS IN THE VEHICLE’S GLOVEBOX AFTER INSTALLATION IS COMPLETED Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: A...
- Page 4 SET SCREW HEX HD M5x20x0.8P HR TOWBALL BOLT ZP BLACK M16x40 2.0P ACRYLIC COMPLIANCE LABEL SPRING WASHER ZP BLACK M16 WIRING LOOM Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: A Page 4 Issue Date:...
- Page 5 2. Remove 2 x screws from inside wheel arch well. 3. Remove 2 x screws and 3 x scrivets from underside of bumper. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: A...
- Page 6 6. Disconnect sensor (shown) from rear panel. Carefully flatten sensor bracket or cut off using an appropriate cutting tool. Sensor will be mounted to towbar later. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: A...
- Page 7 9. Inside boot well, unclip cover on rear most panel to expose tire jack. Remove 1 x push in plastic clip along bottom edge of panel. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au...
- Page 8 12. Remove 1 x rubber cover from behind trim unclipped in Step 11 to expose top of chassis rail. Repeat for opposite side. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: A...
- Page 9 15. Remove 1 x plastic cover from underside of chassis rail covering mounting point. Repeat for opposite side. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: A...
- Page 10 Secure front end of bracket to underside of vehicle tire well with 1 x M10 x 35 mm bolt complete with 1 x M10 washer. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au...
- Page 11 Clean cut area and both holes after to ensure there are no sharp edges or burrs. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: A...
- Page 12 25. Loosen a small section of the weather seal (1) from the boot liner. 26. Remove the rear scuff trim (2) by pulling in an upwards direction. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: A...
- Page 13 33. Tie up patch harness (2) using the supplied Cable Ties (3) to prevent the patch getting caught in the seat belt (4). Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: A...
- Page 14 43. Apply double sided tape to the ECU and secure it to the vehicle sheet metal (1). Note: Ensure when mounting ECU, connector is orientated downwards. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: A...
- Page 15 51. Reinstall LHS trim (1). 52. Remove vehicle storage cover. 53. Remove rear fuse cover (2). Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: A Page 15...
- Page 16 63. Re-install all components following steps 1-7 in reverse. Attached bumper to bumper tabs on towbar through newly drilled holes with 2 x scrivets supplied. Hayman Reese (Cequent) PO Box 4050, Dandenong South VIC 3164 Phone 1800 812 017 Email info@haymanreese.com.au Rev: A...
-
Page 17: Fitting Instructions
*Do not tow with your vehicle if the R CLIP or the SMART PIN NUT is loose or missing. Replacement parts are available from Fig 1. Smart Pin assembly your Hayman Reese Distributor. Insert Trailer Ball Mount (TBM) into towbar HITCHBOX, aligning hole in TBM SHANK with hole in HITCHBOX STEP 1 (Fig.
Need help?
Do you have a question about the 03243W and is the answer not in the manual?
Questions and answers