Pioneer DRM-7000 Service Manual page 129

DRM-7000, DRM-AF751, DRM-AL751, DRM-AH721, DRM-PW701
Demo 2
Preparation :
Set two discs each into Disc slots #001 and #750.
Operational steps :
(1) The disc in slot #001 is carried to the rear Bay #4 drive unit.
(2) The disc in the rear Bay #4 drive unit is returned to slot #001.
(3) The disc in slot #750 is carried to the rear Bay #4 drive unit.
(4) The disc in the rear Bay #4 drive unit is returned to slot #750.
Note: The above steps (2) to (4) constitute one cycle.
Modifiable setting items :
• Disc slot number for the first disc (Default: #001)
• Disc slot number for the second disc (Default: #750)
• Bay number of the drive unit (Default: Bay #4)
Note: The modified settings will be retained until the power is
turned off.
Indications
OK
To interrupt this mode,
press ESC .
Set
ENT
ENT
ENT
Press ENT to display the Flip-Box Setting OK/Set screen.
Note 1: In the following cases, the setting will not be accepted:
• When a specified magazine is not installed. (Even the default
setting will not be accepted if the magazine is not installed.)
• When a disc has been set in the specified drive unit.
Note 2: The approximate time for changing discs is calculated
according to the time from just after the spinning-stop
process is completed until just before the spinning-start
process is started. (Although the drive is not controlled in
this mode, the time just before a drive-control command is
processed is included.)
The time is rounded off to two decimal places.
Note 3: If the specified disc is not set in the specified magazine,
error EF8 is generated.
If the disc is in the flip-box,
"–– Flip ––" is displayed.
"CYC" indicates the number
of cycles (max.: 999999),
and the approximate time for
changing discs.
To restart the operation
without clearing the cycle
number, press ENT.
The number of any disc slot
with no magazine will be also
displayed and can be assign-
ed, but will not be accepted.
You can set a magazine after
assignment.
Any bay number with no drive
unit is displayed and can be
assigned.
This indication is only
displayed when a Flip-box
is recognized.
Demo 3
Preparation :
• Set four discs each into Hyper magazines #1 to #4 (from the
lowest to the fourth slots).
• Discs should not be inserted into other Hyper magazines.
Operational steps :
(1) The discs in Hyper magazines #1 to #4 are carried to Minimum
magazines #1 to #4.
(2) The disc in Minimum magazine #3 (the second disc from the
top) is carried to the Hyper magazine #5.
(3) The disc in Minimum magazine #1 (the lowest disc) is carried
to Hyper magazine #3.
(4) The disc in Minimum magazine #4 (the upper disc) is carried
to Hyper magazine #6.
(5) The disc in Minimum magazine #2 (the third disc from the
top) is carried to Hyper magazine #4.
Note: Reverse steps (2) through (5) above, and when all discs return
to Minimum magazines #1 to #4, one round is completed.
Repeat this for the 2nd round.
(6) The discs in Minimum magazines #1 to #4 are carried to Hyper
magazines #1 to #4.
Modifiable setting items :
• Possible number of rounds: 1 to 999 (default: 2 rounds).
Infinity can be also assigned.
Note: The modified setting is retained until the power is turned off.
Indications :
OK
Hyper magazines
prepared.
Specified number
of rounds completed.
All discs have been returned
to the Hyper magazines.
To interrupt this mode,
press ESC .
If the operation is interrupted, and
discs are returned to the Hyper magazines:
Set
Note: "OK" is not accepted if the Hyper magazines are not inserted.
A disc is being carried from
the Hyper magazine to the
Minimum magazine.
The disc slot numbers from
and to which the disc is
being carried and the round
number are displayed.
The left round number is the
current round number.
A disc is being carried from
the Minimum magazine to
the Hyper magazine.
Select whether you wish to
continue or return the discs
to the Hyper magazines.
You can also select "Infinity".
129