Download
Share
Print this page
Icom Amateur IC-2200H Quick Reference Manual
  1. Manuals
  2. Brands
  3. Icom Manuals
  4. Radio
  5. IC-2200H
  6. Quick reference manual

Icom Amateur IC-2200H Quick Reference Manual

Hide thumbs Also See for Amateur IC-2200H:
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
QUICK REFERENCE GUIDE
■ Installation
D Location
Select a location which can support the weight of the trans-
ceiver and does not interfere with driving in any way. We rec-
ommend the locations shown in the diagram below.
NEVER place the transceiver where normal operation of the
vehicle may be hindered or where it could cause bodily injury.
NEVER place the transceiver where air bag deployment may
be obstructed.
DO NOT place the transceiver where hot or cold air blows di-
rectly onto it.
AVOID placing the transceiver in direct sunlight.
I
D Using the mounting bracket
➀
Drill 4 holes where the mounting bracket is to be installed.
• Approx. 5.5–6 mm (
1
⁄
") when using nuts; approx. 2–3 mm (
4
when using self-tapping screws.
➁
Insert the supplied screws, nuts and washers through the
mounting bracket and tighten.
➂
Adjust the angle for the clearest view of the function dis-
play.
Nut
Spring washer
Flat washer
When using
self-tapping
screws
Spring
washer
IMPORTANT!
Detailed installation notes for Icom mobile transceivers to
be fitted into vehicles are available. Contact your Icom
dealer or distributor.
1
⁄
")
8
Mounting
bracket
Mounting
nut

Advertisement

loading
Need help?

Need help?

Do you have a question about the Amateur IC-2200H and is the answer not in the manual?

Questions and answers

Related Manuals for Icom Amateur IC-2200H

Summary of Contents for Icom Amateur IC-2200H

  • Page 1 Flat washer Mounting bracket AVOID placing the transceiver in direct sunlight. When using self-tapping screws Mounting Spring washer IMPORTANT! Detailed installation notes for Icom mobile transceivers to be fitted into vehicles are available. Contact your Icom dealer or distributor.
  • Page 2 QUICK REFERENCE GUIDE D Battery connection D DC power supply connection ☞ NEVER connect the transceiver directly to a 24 V battery. Use a 13.8 V DC power supply with at least 15 A capacity. ☞ DO NOT use the cigarette lighter socket for power con- Make sure the ground terminal of the DC power supply is nections.
  • Page 3 QUICK REFERENCE GUIDE • Antenna connector D Antenna installation The antenna uses a PL-259 connector. • Antenna location To obtain maximum performance from the transceiver, select • PL-259 CONNECTOR a high-quality antenna and mount it in a good location. A non- q Slide the coupling ring 30 mm radial antenna should be used when using a magnetic mount.
  • Page 4 QUICK REFERENCE GUIDE ■ Your first contact 2. Tune the desired frequency [DIAL] will allow you to dial in the frequency you want to op- Now that you have your IC-2200H installed in your car or erate. Pages 9 and 11 will instruct you on how to set the tun- shack, you are probably excited to get on the air.
  • Page 5 QUICK REFERENCE GUIDE ■ Repeater operation 1. Setting duplex Using the HM-133V Plus or minus duplex selection and the repeater tone setting Push [LOW ] for 1 sec. once or twice to select minus can be made easily via HM-133V. duplex or plus duplex.

  • Page 6: Programming Memory Channels

    QUICK REFERENCE GUIDE ■ Programming memory channels The IC-2200H has a total of 207 memory channels (including Using the HM-133V 6 scan edges and 1 call channel) for storing often used oper- q In VFO mode, set the desired operating frequency, includ- ating frequency, repeater settings, etc.