Sealey PT1170H.V2 Manual

thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear safety
instructions footwear
1. Safety
only open bottomed euro type pallets can be used with this truck
9
DO NOt use a faulty or damaged truck.
8
Before using the truck all parts and working mechanisms should be checked for wear or damage. Pay particular attention to the wheels,
9
handle and fork lifting and lowering mechanism. Any parts found to be worn, damaged or suspect should be repaired or replaced before
the truck is used.
All repairs must be carried out by an authorised Sealey service agent.
9
Personnel who operate the truck and those in the vicinity of operation should wear safety footwear with reinforced toe caps at all times.
9
never place any part of your body in the lifting mechanism or under the forks or load.
9
DO NOt allow others to ride on the truck.
8
DO NOt lift or move unstable or loosely stacked loads.
8
Take extra care when operating a loaded truck in high winds.
9
Take special care when moving long, high or wide loads in order not to dislodge the load by striking any fixtures, vehicles or people in
9
the area of operation.
Always ensure that the load is evenly distributed across the forks with the centre of the load being at the halfway point of the length of
9
the forks.
DO NOt overload the truck - refer to the specification for maximum permitted load.
8
If a load is left unattended even for a very short period of time it should be lowered to the ground.
9
When not in use the truck should be left in the lowered position.
9
ensure that the width and length of the forks is correct for the pallet to be lifted.
9
ensure that the truck is sufficiently inserted into the pallet to lift the full width of the pallet.
9
Use the truck on level, flat, hard surfaces and in well lit areas.
9
DO NOt use truck on sloping or uneven ground; DO NOt attempt to negotiate curbs, steps or ramps.
8
The operator of the truck must be physically capable of controlling the load selected; particularly in relation to stopping a rolling load.
9
2. iNtrODuctiON
Heavy-duty high lift pallet truck suitable for the loading/unloading of light commercial vehicles as well as warehouse/general handling duties.
Features twin stabilisers for extra balance when at maximum lift and an ergonomic handle design for comfortable operation.
3. SPecificatiON
Model no: .......................................................... PT1170H.V2
Capacity: .................................................................... 1000kg
Fork Spread: .............................................................. 225mm
Forks (length x overall Width): ......................1170 x 540mm
Maximum Height: ....................................................... 840mm
Minimum Height: .......................................................... 85mm
nett Weight: ............................................................ 111.00Kg
4. aSSembly
4.1. assembling the handle to the truck (fig.1)
4.1.1. note that the piston is constrained in the down position by a pin which passes through holes in
the handle mounting bracket (fig.1.B). DO NOt remove this pin yet.
4.1.2. Identify and have ready the handle pivot pin (fig.1.A) which will have a roll pin inserted
through one end of it.
4.1.3. Slide the base of the handle into the handle mounting bracket which is an integral part of the
pump body and align the holes in the handle with the holes in the bracket (fig.1).
4.1.4. drive the pin (fig.1.A) through the aligned holes from left to right using a soft faced hammer
and ensure that the roll pin rests in the groove in the bracket (fig.1.d)
4.1.5. Move the lever at the top of the handle (fig.2) into the lower position then pass the chain with
adjusting bolt and nut through the hole in the centre of the handle pivot pin.
4.1.6. lower the handle to depress the piston and remove the restraint pin from the hole 'B' above
the piston (fig.3.B). Place the lever in the central 'raise' position.
4.1.7. Press and hold down the foot pedal (fig.3.A). Slide the adjusting bolt and nut at the end of the
© Jack Sealey limited
Pallet truck 1000kg 1170 x 540mm HigH
lift
Pt1170H.V2
Model no:
Original Language Version
fig.1
PT1170H.V2 Issue 3 (HF) 07/02/19