Sealey PH250.V4 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear protective
instructions gloves
1. safety
1.1. electrical safety
warNiNg! it is the user's responsibility to check the following:
‰
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and
all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance test) tested.
electrical safety information, it is important that the following information is read and understood.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse - see
9
fuse rating in these instructions.
DO NOt pull or carry the appliance by the power cable.
8
DO NOt pull the plug from the socket by the cable.
8
DO NOt use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or
8
replaced immediately by a qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
9
if the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
general safety
1.2.
warNiNg! ensure Health & safety, local authority, and general workshop practice regulations are
‰
adhered to when using this equipment.
familiarise yourself with the application, limitations and potential hazards of the hoist.
9
warNiNg! disconnect the hoist from the mains power before changing accessories, servicing or
‰
performing any maintenance.
maintain the hoist in good condition (use an authorised service agent).
9
replace or repair damaged parts. use genuine parts only. unauthorised parts may be dangerous and will invalidate the warranty.
9
locate hoist in a suitable work area, keep area clean and tidy and free from unrelated materials. ensure that there is adequate lighting.
9
warNiNg! ensure that the mounting for the hoist is capable of supporting the rated capacity of the hoist (plus the weight of the
‰
hoist) without failure and that the hoist is mounted horizontally.
Keep the hoist clean for best and safest performance and check moving parts alignment regularly.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
ensure the load is correctly secured before operating the hoist.
9
Keep hands away from the cable reel when winding the hoist in.
9
DO NOt use the hoist for any purpose other than that for which it is designed.
8
DO NOt operate the hoist if any parts are damaged or missing as this may cause failure and/or possible personal injury.
8
DO NOt exceed the rated capacity of the hoist.
8
DO NOt adjust or tamper with the maximum lift cut-out mechanism.
8
DO NOt use the hoist out of doors.
8
DO NOt get the hoist wet or use in damp or wet locations or areas where there is condensation.
8
DO NOt allow untrained persons to operate the hoist.
8
DO NOt operate the hoist when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOt use the hoist where there are flammable liquids, solids or gases such as paint solvents, etc.
8
© Jack sealey limited
instructions for
POwer hOist - 250kg / 400kg
model no:
Wear safety
footwear
Original Language Version
Ph250.V4 & Ph400.V3
PH250.V4, PH400.V3 | Issue 2 08/11/16
recommended fuse rating
PH250 .V4 - 13 Amp
PH400.V3 - 13 Amp