Advertisement
Quick Links
2/12 Belford Place CARDIFF NSW 2285
PO Box 109, New Lambton, NSW 2305
Email: mail@steelspan.com.au
Phone: 1300 851 377
Web: www.steelspan.com.au
ABN: 51 155 660 503
Module 10 with Overhead Cabinets Assembly
Outlined below is an installation of the Garage Storage Solution - Module 10 which
contains most of the components of the other Pre-designed Modules. The installation
process is essentially the same for any configuration. Just start from the bottom and
work your way up with Horizontal Beams and positioning each component, and then
outwards with additional bays.
1
Advertisement
Summary of Contents for STEELSPAN STORAGE SYSTEM Module 10
- Page 1 ABN: 51 155 660 503 Module 10 with Overhead Cabinets Assembly Outlined below is an installation of the Garage Storage Solution - Module 10 which contains most of the components of the other Pre-designed Modules. The installation process is essentially the same for any configuration. Just start from the bottom and work your way up with Horizontal Beams and positioning each component, and then outwards with additional bays.
- Page 2 It is important to ensure you position the Garage Storage System on a level floor surface. Important Safety Notice: Steelspan is committed to the upmost safety of its Storage Systems and includes all components in its Pre-designed Modules to ensure cabinetry is securely locked into place.
- Page 3 6. Where provided - attach Pegboard Tool Display 440 to End Frame using current and additional nuts, bolts, washers. 7. Fit End Caps to each end of the Uprights. 8. Ensure all nuts and bolts are firmly tightened. Fixing Horizontal Beams Directions: 1.
- Page 4 Two Horizontal Beam 1800's are positioned above the Large Drawer Tool Cabinets and secured into place using the Locking Pins. Position Four Drawer Tool Cabinet into recesses of Horizontal Beams. Second Four Drawer Tool Cabinet is positioned alongside. wo Horizontal Beam 1800's are positioned above the Four Drawer Tool Cabinets and secured into place using the Locking Pins.
- Page 5 Fitting Work Bench Top (Laminate) Position the benchtop on top of the Horizontal Beams with the front edge protruding 80mm out the front face of the beam. Ensure the Work Bench Top protrudes 15mm past the rear Horizontal Beam for the Metal Pegboard Tool Display to be positioned on.
- Page 6 Secure the Work Bench Top to the front Horizontal Beam using the Wingtek Screws provided. Securing Work Bench Sleeve and Metal Pegboard Tool Display: The optional Work Bench Sleeve (Stainless Steel shown) is simply fitted over the top of the Work Bench Top and is held secure by the addition of the Metal Pegboard Tool Display.
- Page 7 1800mm. Shown is the addition of a 900mm bay to house the Storage Cabinet 1860 for the Garage Storage Solution - Module 10. Firstly, connect an additional End Frame using two Horizontal Beam 900's. Then position the Storage Cabinet 1860 into the recesses of these lower Horizontal Beams.
- Page 8 Shown is the optional Metal Pegboard Tool Display 440 added to the right of the Work Bench Top by securing to the side of the End Frame Fit Overhead Cabinets as shown in the instructions below.
- Page 9 Cabinet 1865 Assembly Instructions Tools Required: Cordless Drill with Phillips Head Drill Bit Components: Rear Wall Panel x 1 Side Panels x 2 Front Panel (with doors): Self Tapping Screws x Roof Panel: Floor Panel: Shelves x 4: Shelf Supports x 20:...
- Page 10 Assembly: 1. Fit the Left Wall Panel to the Rear Wall Panel and fix with self-tapping screws. 2. Fit the Right Wall Panel to the Rear Wall Panel and fix with self- tapping screws.
- Page 11 3. Insert the Front Panel (with doors) into the returns at the front of each Side Panel. No fixing required. 4. Insert the Roof Panel in to the upper cavity and fix with Self Tapping Screws. The Roof Panel has 6 holes on the front and rear face.
- Page 12 Insert the Floor Panel into the lower cavity, ensuring the left and right edge of the Floor Panel is inserted into the side rails. Further secure the cabinet floor with two self tapping screws. Side Rails Insert Floor Panel edges into Side Rails Secure the Floor Panel with Self Tapping...
- Page 13 6. Fit Shelf Supports at desired spacing and insert shelves. 7. Completed Cabinet 1860.
- Page 14 How to install Overhead Cabinets: 1. Fix elbow-brackets to the top of the Overhead Cabinet using the bolts and washers provided. 3. Fix a horizontal beam one slot down from the top of the End Frame. 3. Fix a second horizontal beam directly above the Metal Pegboard Tool Display 2.
Need help?
Do you have a question about the Module 10 and is the answer not in the manual?
Questions and answers