Summary of Contents for Hornady RAPiD SAFE NIGHT GUARD
- Page 1 Owner’s Manual RAPiD SAFE ® NIGHT GUARD ™ With patented RFID technology. Item No. 98215 Instructional videos for Hornady Security ® products are available at hornady.com.
-
Page 2: Warnings And Important Information
RFID tags in a secure location at all times. Store your RAPiD Safe in a ® secure location away from your keys and RFID tags. Hornady Security ® is not liable for unauthorized access, including damage to, or loss of property, or personal injury. -
Page 3: Table Of Contents
Table of Contents Warnings and Important Information ..........Page 1 Items Included..................Page 2 Setup and Operation ................Page 3 Securing Your Safe ................Page 9 Product Registration and Service ............ Page 10 Warranty ....................Page 10 Frequently Asked Questions ............. Page 11 Items included with your RAPiD Safe ®... -
Page 4: Setup And Operation
Safe has been taken out of the box, please check to be ® sure both circular barrel keys fit and unlock your RAPiD Safe. Contact ® Hornady at 800-338-3220 if the keys do not work. Store keys in a secure ® location outside the safe. Open Safe with Key... - Page 5 Batteries To install batteries, press the lower left corner of the battery cover on the front of the safe. Insert four (4) high quality AAA batteries according to the diagram. Replace all batteries at the same time. NOTE: The battery symbol near the clock display will illuminate red when the batteries are weak.
- Page 6 5. If the RFID tag is not programmed, the program function will time out after ten seconds and the safe will return to normal operation. If multiple attempts to program a RFID tag fails, please contact Hornady at 800-338-3220. ®...
- Page 7 RFID Watchband Tag NOTE: Due to potential interference from the body (attenuation), the RFID watchband tag should be worn on the outside or bottom of the wrist and may need to be brought within 1-inch of the reader to activate the safe. The RFID reader will likely not read through the wrist.
- Page 8 How to Remove All Tags From Safe 1. Open the RAPiD Safe with either the key, a previously programmed ® RFID tag, or key code. Locate the red program button. Press and hold the button for five seconds to erase all previously programmed tags. All five red LEDs will begin to blink in sequence.
- Page 9 Closing the Night Guard The safe has a latch closure sensor that will illuminate the LED in the keypad when the drawer is closed. Green – Latch has fully closed. Blinking Red – Latch has NOT fully closed. To close the safe, press the drawer in until the latch clicks. Verify green light appears on the keypad.
-
Page 10: Securing Your Safe
Securing Your Safe Narrowest Diameter To maintain the security of the of Ferrule safe either use the included security cable or bolt the safe to a secure structure. Using the Security Cable Wrap the security cable around a secure object and place the ferrule end through the loop in the cable. -
Page 11: Product Registration And Service
® conformity herewith, Hornady Security will promptly undertake an investigation of such claim. ® If the warranty claim is covered by the Limited Warranty, Hornady Security will, in its sole ® discretion, repair the defect(s) or replace RAPiD Safe at the expense of Hornady Security. -
Page 12: Frequently Asked Questions
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. P.O. Box 1848, Grand Island, Nebraska 68802-1848 308-382-1390 • 800-338-3220 • Fax: 308-382-5761 • Hornady.com/contact 586002 19HMC0119 | 07/2020...
Need help?
Do you have a question about the RAPiD SAFE NIGHT GUARD and is the answer not in the manual?
Questions and answers
How do I disable the display so that it remains dark while still powered on?