Related Manuals for Arconic Huck Powerig 940
Summary of Contents for Arconic Huck Powerig 940
-
Page 1: Table Of Contents
Serial Number Notice Instruction Manual Safety Instructions Hydraulic Powerig® Description Principle of Operation Preparation for Use Specifications Checking and Adjusting Pressures Operation Maintenance Components Drawings 7-10 Options and Accessories Troubleshooting Makers of Huck , Marson , Recoil August 10, 2017 ®... -
Page 2: Serial Number Notice
940 Powerig® (HK496) NOTICE This manual applies to 940 serial number 3927 and above. For any other serial numbers, please contact a Huck customer service representa- tive. -
Page 3: Safety Instructions
940 Powerig® (HK496) Safety Instructions GLOSSARY OF TERMS AND SYMBOLS: specifically designed to do so. - Product complies with requirements set forth 14. Never remove any safety guards or pintail deflectors. by the relevant European directives. 15. Where applicable, ensure deflector or pintail collector is installed and operating prior to use. - Read manual prior to using this equipment. 16. Never install a fastener in free air. Personal injury from - Eye protection is required while using this fastener ejecting may occur. -
Page 4: Description
940 Powerig® (HK496) Description Figures 1 & 5 Figure 1 Model 940 Powerig is a portable, electrically operated ® power source designed to operate all Huck hydraulic Electrical installation equipment excluding Huck-Spin tools. It ® Enclosure operates on 115 volt AC, 50-60 Hz, one-phase electrical Motor power. -
Page 5: Specifications
940 Powerig® (HK496) Specifications CSA-US CERTIFIED RESERVOIR CAPACITY: 2.6 gallons (9.8 liters) 940 Powerigs are intended for use in indoor factory environments, and if used outdoors they must be PRESSURE SETTING AS SHIPPED: protected from the elements. RETURN: 2,200-2,400 psi (15,200-16,500 kPa) WIDTH: 16.1 inches (40.9 cm) PULL: 5,400 - 5,700psi (37,200 - 39,300 kPa) LENGTH: 13.9 inches (35.4 cm) Minimum Operating Temperature (ambient): 0° (18°C) HEIGHT: 18.5 inches (47 cm) Maximum Hydraulic Fluid Temperature: 150°F (65°C) WEIGHT: 66 pounds (30 kg) (with empty reservoir) -
Page 6: Maintenance
940 Powerig® (HK496) Maintenance PREVENTIVE MAINTENANCE PUMP OVERHAUL An effective preventive maintenance program includes If pump requires overhaul return it, or the complete unit, to scheduled inspections to detect and correct minor troubles. the nearest repair facility shown on the inside back cover. Perform the following steps monthly during normal use: REPLACING PUMP-TO-MOTOR COUPLING · Ensure secure fir of hydraulic and electrical fittings. -
Page 7: Components Drawings
940 Powerig® (HK496) 111345 Pump, Motor, Valve Assembly Figure 4 107317 Filler/Breather 115753 Pressure Switch Assembly 111415 Motor Brush 500071 Screw (10) 106397 External 112625 Pilot Relief Valve Valve Adapter Plate Note: This assembly is purchased complete. The bill of material 111346 Motor 500067 listed is for reference and... - Page 8 940 Powerig® (HK496) 123490 Electrical Enclosure Assembly Figure 5...
- Page 9 940 Powerig® (HK496) Electrical Schematic and Wiring Diagram Figure 6...
- Page 10 940 Powerig® (HK496) 111346 Motor Figure 7 111346_revE...
-
Page 11: Options And Accessories
940 Powerig® (HK496) Options & Accessories OPTIONS Rig Transport Dolly 129703 940T-1 (Special Version of 940) Heavy duty steel dolly for easy movement of powerig The 940T-1 is part of Huck’s revised aftermarket Truck throughout the work area. Kits, which contain different pressure installation tools. This hydraulic unit will be shipped from the factory with Motor 111346 output pressures set as follows:... - Page 12 940 Powerig® (HK496) Record your own notes here.
- Page 13 940 Powerig® (HK496) Limited Warranties Limited Lifetime Warranty on BobTail® Tools: Tooling, Part(s) and Other Items not manufactured by Huck: Huck International, Inc. warrants to the original purchaser that its BobTail® installation tools manufactured after HUCK makes no warranty with respect to the tooling, 12/1/2016 shall be free from defects in materials and part(s), or other items manufactured by third parties.
- Page 14 Arconic Inc. (NYSE: ARNC) creates breakthrough products that Through the ingenuity of our people and cutting-edge advanced shape industries. Working in close partnership with our customers, manufacturing, we deliver these products at a quality and efficiency we solve complex engineering challenges to transform the way we that ensures customer success and shareholder value.
Need help?
Do you have a question about the Huck Powerig 940 and is the answer not in the manual?
Questions and answers