Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DSPPA PoE6311
Summary of Contents for DSPPA PoE6311
- Page 1 IP Network Ceiling Speaker PoE6311 User Manual Thank you for using our DSPPA public address system. Please read this User Manual carefully to make better use of this equipment. G u a n g z h o u D S P P A A u d i o C o .
- Page 2 This page is left blank for users’ notes.
- Page 3 About the User Manual This User Manual is available and effective upon completion of development of the PoE6311 Ceiling Speaker. The User Manual includes system description, matters needing attentions in use, instructions on system connection, instructions on use of product and technical specifications of the terminal. Please read this User Manual carefully before connection, installation and use and operate in accordance with corresponding instructions in the Manual.
-
Page 4: Table Of Contents
2.1 Side Panel................................2 III. Connection Diagram ............................. 3 3.1 PoE6311Application Diagram in the System.......................3 3.2 PoE6311 Interface Connection Diagram......................4 IV. IP Address Setting of the Terminal on the Host....................5 4.1 IP Address Setting..............................5 4.2 Sound Effect Adjustment............................7 V. -
Page 5: Product Description
I. Product Description 1.1 About PoE6311 Ceiling Speaker PoE6311 ceiling speaker is a network full-digital analog-digital conversion signal processor based on the TCP / IP transmission protocol, which can be mounted to any place accessible to network. The remote audio data steam can be output as audio signal through the equipment with intelligent host control. -
Page 6: Appearance Description
IP Network Ceiling Speaker II. Appearance Description 2.1 Side Panel Mircos SD SPEAKER DC/+15V PoE INPUT OUTPUT Power supply interface DC power supply. (Note: You can use this interface for power supply when not using PoE power supply) PoE interface Connect a PoE switch with 48V and AT mode output when used for data and power transmission, and connect a common switch network port when only used for data transmission. -
Page 7: Connection Diagram
The above figure is for illustrative purposes only. Please refer to the system connection diagram for ② the specific connection. The PoE6311 in the system must be powered by 48V IEEE802.3at standard switch port, and set the ③ corresponding address before connecting with the host. -
Page 8: Poe6311 Interface Connection Diagram
IP Network Ceiling Speaker 3.2 PoE6311 Interface Connection Diagram Interface connection diagram 48V, AT mode PoE switch Mircos SD SPEAKER DC/+15V PoE INPUT OUTPUT PoE6311 speaker Dedicated ceiling speakers... -
Page 9: Ip Address Setting Of The Terminal On The Host
IP Network Ceiling Speaker IV. IP Address Setting of the Terminal on the Host 4.1 IP Address Setting This speaker can be customized to modify the network parameters. Please read this section carefully if you need to use this function. The alteration methods are as follows: Method 1：... - Page 10 IP Network Ceiling Speaker (Pic. 2) Method 2: Enter the host software “Settings” -> “System Maintenance” -> “Device Maintenance”. Find the IP address of the indoor ceiling speaker, select and click Modify. As shown in the Pic. 3 below, modify the parameters and click OK to display Success. (Pic.
-
Page 11: Sound Effect Adjustment
IP Network Ceiling Speaker 4.2 Sound Effect Adjustment As the method 1 in the 4.1 above, first ensure that the host / computer and the terminal must be on the same network segment, and then enter the terminal IP address on the IE browser to enter the interface below. Slide the tone adjustment roller to adjust the high and low volume of the speaker, and click the “Save”... -
Page 12: Installation
IP Network Ceiling Speaker V. Installation Dimension Mounting hole 162mm 162mm Mircos SD EAKER Mircos SD SPEAKER UTPUT DC/+15V PoE INPUT OUTPUT SPEAKER PoE INPUT DC/+15V OUTPUT 185mm 185mm Just 120mm above your ceiling. 1. Cut a diameter of 170-175mm mounting hole on the ceiling (as shown above). 2. - Page 13 IP Network Ceiling Speaker Safety Precautions 1． Safety Precautions Please do NOT connect this device to the power source, before the system is correctly wired. It is important to ensure that input voltage to the device is the same as required voltage of the ...
-
Page 14: Specification
IP Network Ceiling Speaker Specification Item Parameter Model PoE6311 Bass 0～14 (±2) (60Hz) Tone Adjustment Treble +7，-8 (±2) (10KHz) ≤1% Effective Output Power ≧9W Input Sensitivity -10±1dB Frequency Response 40-18KHz (±3dB) SNR (A) ≧70dB Power 2×9W Power Supply IEEE 802.3 at PoE Package Size 255×255×185mm... - Page 15 This is connected to power source via the plug and any failure or danger occurs, the user can disconnect the device from power source by pulling out the plug out from the socket, therefore, it is required that the power socket should be located somewhere with easy access. Guangzhou DSPPA Audio Co., Ltd.
Need help?
Do you have a question about the PoE6311 and is the answer not in the manual?
Questions and answers