Table of Contents
Related Manuals for Adexa HBS-300L
Summary of Contents for Adexa HBS-300L
- Page 1 MEAT SLICER INSTRUCTION MANUAL Model MEAT SLICER HBS-300L ● HBS-300A ● HBS-275A ● HBS-250L ● HBS-250A ● HBS-220A ADEXA DIRECT LIMITED GROUND FLOOR UNIT 1 214 PURLEY WAY CROYDON CR0 4XG LONDON UNITED KINGDOM service@adexa.co.uk www.adexa.co.uk +44 1483 931040...
- Page 2 INTRODUCTION: You should read this user manual carefully before using the appliance. This appliance is intended for commercial use only and must not be used for household use. The appliance must only be used for the purpose for which it was intended and designed.
- Page 3 Make sure the cord does not come in contact with sharp or hot objects and keep it away from open fire. To pull the plug out of the socket, always pull on the plug and not on the cord. Ensure that the cord (or extension cord) is positioned so that it will not cause a trip hazard.
-
Page 4: Special Safety Regulations
SPECIAL SAFETY REGULATIONS: • This appliance should be operated on a level, horizontal, dry, stable and heat resistant surface. • This appliance should be operated by trained personnel. • The user must wear close-fitting dressing during operation. Scarf is not allowed. - Page 5 CONTENTS: Slicer parts Blade sharpener Stop plate Carriage On/off switch Slice thickness dial Product clamp Blade guard Blade Carriage lock Blade guard bolt (not displayed)
- Page 6 Top view of the appliance Attach the sharpening module in such a way that the blade does not move between the wheels. Secure the sharpening device to the machine by tightening the holder. Check to make sure that the sharpening device is well secured before using the machine. NOTE! The sharpening device is equipped with a safety switch.
- Page 7 The plastic safety guard has been removed from the appliance to prevent damage during transit. Safety guard must be fitted before using the machine. Adexa accept no responsibility for any injury caused by operation of this appliance without the guard installed or correctly fitted. 1. Place both screws in the carriage.
- Page 8 3. Place the two washers over the bolts. 4.Screw on the two dome nuts.
- Page 9 Operation 1. Connect the appliance to the power supply 2. Set the thickness to the desired level by turning the Thickness knob anti-clockwise. 3. Place the meat in the cradle and secure in place with the Grip handle. 4. Switch On the power [I]. Warning: Never use your hands to secure the meat when slicing.
- Page 11 SAFE BLADE REMOVAL TOOL The blade cleaning must be carried out with metal gloves and a wet cloth! Unplug the slicer from the power supply. Remove the blade guard cover by unscrewing the pin at the back of the appliance. Place and fit the supplied blade removal tool with the notch at the right top side.
-
Page 12: Cleaning, Care And Maintenance
CLEANING , CARE AND MAINTENANCE: • Always turn off and disconnect the appliance from the power supply before cleaning. Always use extreme care when handling the blade. • Use soapy water and a damp cloth to clean the appliance. • Clean the appliance regularly. - Page 13 4. Carefully lift off the blade cover. 5. Attach the blade removal tool by placing it over the blade and screweing two bolts into the corresponding holes in the balde. 6.Unscrew the 3 screws holding the blade, leaving it sat on the slicer. 7.Lift the blade off the slicer using the knobs of the blade removal tool as handles.
-
Page 14: Sharpening The Blade
SHARPENING THE BLADE: If the meat slicer begins to produce uneven or broken slices, it may be blunt and require sharpening. To sharpen the blade: To sharpen the blade: Unscrew the Sharpener release bolt and lift off the blade sharpener. Rotate the sharpener 180°... -
Page 15: Lubricating The Pusher Axle
LUBRICATING THE PUSHER AXLE: 1. Push the carriage to one side and clean the axle with a dry cloth. 2. Lubricate the axle surface with grease suitable for use in food preparation areas. 3. Push the carriage backwards and forwards several times to distribute the grease evenly. -
Page 16: Troubleshooting
TROUBLESHOOTING: Problem Possible cause Solution Appliance does not slice well Blunt blade Sharpen blade Dirty appliance Clean the appliance Appliance stops slicing Overheated motor Let the machine cool off for an extended period. The motor’s safety thermostat will reset itself automatically. - Page 17 Technical Specifications Model: HBS300L HBS250L HSB-300A Voltage 220-240V 50HZ 220-240V 50HZ 220-240V 50HZ Power 250W 150W 250W Slicing 0~15mm 0~12mm 0~15mm thickness Blade 300mm 250mm 300mm diameter Max slicing 22mm 18mm 22mm width Weight 22.30KGS 16.40KGS 21.10KGS Measurement 597x520x495MM 537x460x400MM 597x520x495MM Noise Level <...
-
Page 18: Electrical Wiring
ELECTRICAL WIRING This appliance is supplied with a 3 pin, moulded, BS1363 plug and lead, with a 3 amp fuse as standard. The plug is to be connected to a suitable mains socket. This appliance is wired as follows: • Live wire (coloured brown) to terminal marked L •... -
Page 19: Spare Part List
SPARE PART LIST... - Page 22 Adexa products have undergone strict product testing in order to comply with regulatory standards and specifications set by international authorities and have been...
- Page 23 GROUND FLOOR UNIT 1 214 PURLEY WAY CROYDON CR0 4XG LONDON UNITED KINGDOM service@adexa.co.uk www.adexa.co.uk +44 1483 931040 EC Declaration of Conformity Adexa Direct Limited declares that: Equipment Type: Meat Slicer Model: HBS220A, HBS250A, HBS275A, HBS300A, HBS250L, HBS300L Imported By:...
Need help?
Do you have a question about the HBS-300L and is the answer not in the manual?
Questions and answers