Table of Contents
Advertisement
Quick Links
ProSeries II Call Blocker
™
AUTOMATICALLY BLOCKS AND ROUTES
SCREENED CALLS USING CALLER ID
With Back Lighted Display
Patented 10,306,057 & 5,490,210
Full Operations Manual
Copyright 1990-2020 All Rights Reserved. Digitone ProSeries II Call Blocker and
Personal Communicator are trademarks of Digitone Communications, LLC
Advertisement
Table of Contents
Related Manuals for Digitone ProSeries II Call Blocker
Summary of Contents for Digitone ProSeries II Call Blocker
- Page 1 ™ AUTOMATICALLY BLOCKS AND ROUTES SCREENED CALLS USING CALLER ID With Back Lighted Display Patented 10,306,057 & 5,490,210 Full Operations Manual Copyright 1990-2020 All Rights Reserved. Digitone ProSeries II Call Blocker and Personal Communicator are trademarks of Digitone Communications, LLC...
- Page 2 Fake Names using Digitone’s Patented matrix system. Just connect your Phones and you’re ready to go as Digitone’s DPCB can operate right out of the box. No Battery Backup is Needed. If a power outage occurs, all program settings remain intact.
- Page 3 Caller ID repeated. However, blocked calls will not ring the phones connected to the TEL port. Extension phones connected directly to the phone service will ring once on blocked calls. Digitone recommends using a Cordless phone system to distribute rings. Entering (Block) Calls Remotely Using Your Phone...
- Page 4 Caller ID Display ™ Automatic Call Blocking and Routing Caller ID service from your phone company is required for Digitone’s ProSeries Call Blocker to work. The first call to your DPCB unit will initialize the Clock and Date to the current date and time. Automatic call routing will begin to work right after the first call when Caller ID information is displayed.
- Page 5 Fax or Medical Device - If you also have a Fax machine or even a Medical Alert device, these devices need to be in parallel with your ProSeries II Call Blocker so they have a direct connection to the phone line. The DPCB should be used exclusively for your telephones.
- Page 6 Programming Connecting your Telephone to the TEL Jack of the ProSeries Blocker Testing your connection to the DPCB With the ProSeries Blocker powered up, go off-hook with the phone you are using in the TEL port. See if the DPCB shows the Call Progress Timer on the lower line of the display, ex.
- Page 7 Red LED Code 28 - If you don’t want to see the LED flashing at all, you can disable it. Press and hold the Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”, when the prompt for “Enter Code” displays, enter 29. Default is 28. Operating Modes - You can switch between the operating modes using the programming button and by entering one of the mode numbers.
- Page 8 Viewing Caller Lists and Stored Number Removal You can review what numbers are stored in each caller list by entering programming: 1) (Preferred) Take the Phone in the TEL port off-hook, Dial ## or *** to go directly into programming or, 2) press and hold the Program Button for 3 seconds until you see Program Mode, then Pick Up Phone, when the prompt for Enter Code displays enter: Code 21 to view Spoofed Exchange Call list...
- Page 9 Clearing Blocked Numbers List Only Code 40 To delete just the blocked numbers already stored from using the Block Button or with the Last Call Remote Entry command of * 2 #, use Code 40 # *. This lets you clear out all the numbers that accumulated over the years and, also retains the known unwanted blocked entries.
- Page 10 Invited calls are passed through. Note: Extension phones connected directly to the phone service will ring once on blocked calls. Digitone recommends using a Cordless phone system with multiple handsets connected to the TEL port to distribute ringing throughout your home where you may have older wired corded phones permanently connected.
- Page 11 prompt for “Enter Code” displays enter 72, display shows function. If you want to restore Blocking of OPX calls later, enter programming: press and hold the Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”, when the prompt for “Enter Code”...
- Page 12 After Hours Mode Settings Step 1) Monday thru Friday – Start Code 82 & End Time Code 83 Using military time as shown above, set this feature on by enter programming: press and hold the Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”, when the prompt for “Enter Code”...
- Page 13 Display All Operating Codes Code 92 Press and hold the Program Button for 3 seconds until you see “Program Mode”, then “Pick Up Phone”, when the prompt for “Enter Code” displays, enter 9 2 to see the current settings. The factory default list is Pg1: 16, 28, 30, 46, 48, 58, Pg2: 70, 73, 75, 77, 80, 85, Pg3: 87, 91, 96, 66, 03.
- Page 14 INDEX of CODES [92] Page Code 16 FSK CID ENABLED Standard Caller ID Mode (Default Enabled) Code 17 DTMF CID ENABLED Code 20 SPOOFING SAVED Spoofed Number Store (Default Enabled) Code 21 SPOOFING LIST Spoofed Number List Displayed Code 27 CODE SAVED LCD Backlight Time Code 28 LED ENALBLED (Default Enabled) Code 29 LED DISABLED Code 30 STANDARD MODE (Default Enabled)
- Page 15 Code 97 # * REG CALL DISABLE Block All Calls Except Invited Code 98 # * ALL NBR DELETED Code 98 [number] * Delete specified number Code 99 # * DIGITONE DEFAULT Factory Reset ™ Digitone ProSeries II Call Blocker...
- Page 16 NOT INSTALL THIS UNIT OUTDOORS, IT IS NOT WEATHERPROOF! During the period of one year from the date of purchase, Digitone will repair, or at its option, replace defective component part(s) or product upon delivery to the Service Department accompanied by proof of purchase (sales receipt) without charge for parts or labor.
Need help?
Do you have a question about the ProSeries II Call Blocker and is the answer not in the manual?
Questions and answers