NextTech BX4 Original Instructions Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Table of Contents

Need help?

Do you have a question about the BX4 and is the answer not in the manual?

Questions and answers

Summary of Contents for NextTech BX4

Page 2 Original instructions Istruzioni originali 8040BA0 - NEXTTECH B X4...
Page 3: Table Of Contents
TABLE OF CONTENTS General information..................................2 Purpose of the manual................................2 ..........................3 Safety information..................................3 Safety regulations..................................3 .................................... 4 Safety signals....................................5 Technical information................................. 6 ................................6 ............................7 Main parts....................................8 Installation.
Page 4: General Information
GENERAL INFORMATION PURPOSE OF THE MANUAL • • • • • • • • Danger - Attention This symbol indicates situations involving imminent danger, which, if ignored, could put people’s health and safety at risk. Warning – Caution This symbol indicates situations where it is necessary to behave in a certain way in order to avoid putting people’s health and safety at risk, and to protect the device.
Page 5: Safety Information
IDENTIFICATION OF MANUFACTURER AND EQUIPMENT DATA PLATE (A) Name of manufacturer (C) Model (C) Version (C) Manufacturing year Xxxxxxxxxxxxxxxxxx, Xxxxxxxxxxxxxxxxx Manufactured by XXXXX Xxxxxxxxxxxxxxxxxxxxxxxx (XX) - XXXX MODEL TYPE Serial Number : XXXXXXXXXXXXXX (D) Technical (C) Serial (B) EC conformity specifications number label...
Page 6 • • • watertight. • • • • • • • • • • SAFETY DEVICES 1. Obstacle detector 2. Inclinometer 3. Emergency stop switch at any time during operation will immediately stop the movement of the lawnmower robot and the rotation of the blade will stop. 4.
Page 7: Safety Signals
SAFETY SIGNALS running. to understand meanings before pets and other people at a safe suitable times. when it is running. Wait until the blade and rotating parts Warning! Do not spray water on STOP pets and other people at a safe suitable times.
Page 8: Technical Information
TECHNICAL INFORMATION TECHNICAL SPECIFICATIONS Modello Description 8040BA0 8040BA0 8040BA0 2.9Ah - 2A 5.8Ah - 5A 8.7Ah - 8A Power KIT MEDIUM PREMIUM 1200 1800 Features 635x464x300 " 20 - 65 Diameter of blade Motors without brushes Cutting blade speed Ground speed Metres / Minute installed.
Page 9 Frequencies Transmitter for the robot driving Bluetooth Equipment / Accessories / Functions Rain sensor Standard Standard Optional station Maximum length of perimeter wire 1000 GENERAL DESCRIPTION OF THE APPLIANCE RANDOM OPERATION grass in gardens and house lawns at any time of the day or night. perimeter wire.
Page 10: Main Parts
MAIN PARTS MODEL 8040BA0 Version Robot Rain sensor Handle Cutting blade Pegs Charging station User manual Important In some commercial setups, the power kit may be sold separately. POWER KIT LIGHT MEDIUM PREMIUM Battery 25.9V 2.9Ah 25.9V 5.9Ah 25.9V 8.7Ah Power Supply unit 2.0 A 5.0 A...
Page 11: Installation
INSTALLATION PACKING AND UNPACKING Warning – Caution Keep plastic wrapping and plastic containers away from infants and children: risk of suffocation! Important Keep the packaging materials for future use. PLANNING OF SYSTEM INSTALLATION • transmitter Power supply unit Warning – Caution Min.
Page 12 • • the soil or humid environments; position it on the outside of the lawn and not inside; to the power supply unit. Do not shorten or lengthen the • power supply unit transmitter charging station min height 160 cm / 63 "...
Page 13: Setting Up Of The Perimeter Wire
SETTING UP OF THE PERIMETER WIRE track for laying the perimeter wire 4. Installation of the perimeter wire. RE-ENTRY METHOD TO THE CHARGING STATION “Follow wire” “V-Meter” step lower 2 mt. 5 cm. 2 mt. 2 mt. charging station station. 2 mt.
Page 14 SETUP OF THE ROBOT’S QUICK RE-ENTRY TO THE CHARGING STATION the path and where the perimeter length is greater than 200 meters. the perimeter wire on the opposite side. Important An incorrect setup of the robot’s quick re-entry may prevent the robot from returning to the charging station quickly.
Page 15 PREPARATION AND MARKING THE BOUNDARIES OF THE WORK AREAS Preparation of the lawn to be mowed The perimeter wire must be laid on the ground sloping no more area. Important Areas with slopes greater than those allowed cannot be mowed with the robot. Therefore, position the perimeter wire in front of the slope so that it is excluded from the area to mow.
Page 16 Marking the boundary of the work area Track for laying the perimeter wire min. 70 cm / 27,56 " min. 70 cm / 27,56 " perimeter wire. min. 70 cm / 27,56 " The minimum passage allowed is 70 cm edge of the perimeter wire.
Page 17 Important The illustration shows an example of the elements inside and on the perimeter of the work area and the distances to follow for the correct laying of the perimeter wire. Mark the boundary of elements in iron or other metals (drain covers, electric connections, etc.) to prevent any interferences to the signal of the perimeter wire.
Page 18 paragraphs. Important proper functioning of the robot. Increase the distance by at least 30 cm (11.81 ") in the presence of slopes or slippery ground. 90 cm. / 35,44 “ 90 cm. / 35,44 “ 90 cm. / 35,44 “ the robot to move regularly.
Page 19: Installation Of Perimeter Wire
INSTALLATION OF PERIMETER WIRE perimeter wire Important Start laying the perimeter wire from the area where the charging station is installed, leaving a couple of Max. extra meters so that it can be cut down to size when 5 cm (1,96 ") Ground wire 35 cm (13,78 ")
Page 20 Joining of the perimeter wire the installation. button on the upper side all the way down using a pair of pliers. Important For a safe and secure electrical connection, only use original joints. Do not use insulating tape or other types of joints that do not provide proper isolation (lugs, terminals, etc.).
Page 21 screw anchors (Q) pegs (P) charging station (N) current power supply unit (A) transmitter (B) outlet. Perimeter wire H. min. 160 cm (63.00 ") power cord (E) charging station (N) protection (L) User’s manual...
Page 22: Adjustments
BATTERY CHARGING ON FIRST USE “ON” KEY “PLAY/PAUSE” KEY Important 4 hours. ADJUSTMENTS ADJUSTMENT RECOMMENDATIONS Important The user must make any adjustments according to the procedures described in this manual. Do not make any adjustments which are not expressly indicated in this manual. Any special adjustments, not expressly indicated in this manual, must only be performed by personnel from the Manufacturer’s authorised service centre.
Page 23: Use And Operation
USE AND OPERATION REQUIREMENTS FOR USE Important it, especially the safety recommendations. Only use the robot for its intended purpose as described by the Manufacturer and do not tamper with any device to obtain different operating performances. Do not use the robot and its peripheral units in bad weather conditions, especially when there is a risk of lightning.
Page 24: Set Up
SET UP • • • • • • • • Operation of the robot in manual mode with “AUTO LED off” • • • • Operation of the robot in automatic mode with “AUTO LED on” • • again. • User’s manual...
Page 25 USE OF THE ROBOT IN CLOSED AREAS WITH NO CHARGING STATION Danger - Attention Carry the robot using the handle provided. Do not grab the robot by the body and always use the handle provided. min. 100 cm (39,37 ") min.
Page 26: Menu Settings - Programming Mode
MENU SETTINGS – PROGRAMMING MODE Robot Programming Important To get the best out of the robot, it is recommended to program the robot to work every day. If several working areas need to be set, it is recommended to program at least two working schedules in order to increase the cutting frequency in the areas.
Page 27 Re-entry to charging station robot will position its wheels on either side of the perimeter wire to return to Install the perimeter wire using the “On the Wire” method, refer to the section “Re-entry method to the charging station”. near the perimeter wire. Install the perimeter wire using the “V-Meter”...
Page 28 Work schedule dimension. DIMENSION DISTANCE 6000 distance. area by following the perimeter wire. To ensure that the robot starts DISTANCE WIRE DIRECTION ECO MODE direction. primary area wire distance. passages; ECO mode. secondary area 1 (30%, 60MT, clokwise) move to the next step. anti-clockwise direction clockwise direction General settings...
Page 29: Robot Safety Stop
ROBOT SAFETY STOP “STOP” KEY (A) Important The robot safety stop is necessary during maintenance and repairs (for example, blade replacement, cleaning operations, etc.). PROLONGED INACTIVITY AND RESTARTING • • • • • • User’s manual...
Page 30 Restarting Current power supplyunit (A) Charging station (C) BATTERY CHARGING AFTER PROLONGED INACTIVITY Danger - Attention Do not recharge the robot in explosive and “ON” KEY (A) “PLAY/PAUSE” KEY (B) “OFF” KEY (C) User’s manual...
Page 31: Operating Tips
OPERATING TIPS blade and then lower it gradually on the following days; the battery life; of the day. ROUTINE MAINTENANCE MAINTENANCE RECOMMANDATIONS Important During maintenance, use personal protection equipment indicated by the Manufacturer, especially when working on the blade. Before carrying out any type of maintenance, make sure the robot is turned off (see “Robot Safety Stop”).
Page 32 ROBOT CLEANING Warning – Caution Use protective gloves to prevent cutting your hands. Warning – Caution The use of too much water may cause water to penetrate into the device which could damage the electrical parts. 4. Do not wash the inside parts of the robot and do not use jets of pressurised water so as not to damage the Warning –...
Page 33: Troubleshooting
TROUBLESHOOTING TROUBLESHOOTING GUIDE to see what the problem is. Warning – Caution Safely stop the robot (see “Robot Safety Stop”) in case it is necessary to check the robot, in order to avoid danger of accidental blade starting. Problem Cause Remedies Cutting blade damaged Warning –...
Page 34 Problem Cause Remedies Warning – Caution and/or residuals Use protective gloves to prevent injuries to your hands. Cutting blade worn out The batteries are about to run out. Programming error Date and time not set smartphone to update the date and time Cutting blade damaged Danger - Attention Use protective gloves to prevent cutting your...
Page 35: Part Replacement
Problem Cause Remedies Turn the robot off and on. Fixed orange light No power supply The led not turn on Interrupted fuse transmitter Interrupted perimeter wire supply unit. Join the perimeter wire is on PART REPLACEMENT RECOMMENDATIONS FOR REPLACING PARTS Important Replace and repair any parts according to the manufacturer’s instructions, or contact the service centre if these operations are not included in the manual.
Page 36: Robot Disposal
ROBOT DISPOSAL • • • • Danger - Attention WEEE - Waste Electric and Electronic Equipment (WEEE) can contain dangerous substances with potentially harmful effects on the environment and people's health. WEEE must be disposed of correctly and only in •...
Page 37: Ec Declaration Of Conformity
EC DECLARATION OF CONFORMITY ZUCCHETTI Centro Sistemi S.p.A. Via Lungarno 305/A Terranuova B.ni (AR) ITALY Machinery directive electromagnetic compatibility directive Radio (RED) directive RoHS directive WEEE directive directive for noise emission in the environment 2005/88/EC; safety emission emission immunity WEEE – Equipment marking Electromagnetic compatibility Electromagnetic compatibility Terranuova B.ni 02/10/2019...
Page 38: Warranty Rules
WARRANTY RULES CONDITIONS AND LIMITATIONS HOW TO REQUEST WARRANTY SERVICE • • and name of the dealer. • ADDITIONAL DEFINITIONS of use; On-site support • • by unauthorised third parties; Suggestions • • • Please note • the motors have a warranty of 2 years with limit at 3000 User’s manual...