Related Manuals for POP UP MI TOWER
Summary of Contents for POP UP MI TOWER
- Page 1 A S S E M B L Y G U I D E F OR MITOWE R TOWER +44 (0)1244 833 933 info@popupproducts.co.uk popupproducts.co.uk...
-
Page 2: Table Of Contents
A S S E M B L Y G U I D E FO R M ITOW ER CONTENTS CONTENTS GETTING STARTED INTRODUCTION MITOWER 2M - ASSEMBLY KNOW YOUR MITOWER MITOWER 2M - ASSEMBLY KNOW YOUR MITOWER’S COMPONENTS MITOWER 3M - ASSEMBLY KNOW YOUR KIT LIST AND SPECIFICATIONS MITOWER 3M - ASSEMBLY KNOW YOUR STORAGE AND TRANSPORT PACK... -
Page 3: Introduction
7 and 8. We want you to enjoy the safe and responsible use of MI TOWER with the minimum of fuss and this guide is designed to get you up and running as quickly and as safely as possible. -
Page 4: Know Your Mitower
KNOW YOUR MI TOWER PA R T S L I S T I N G 4 RU NG F RA M E A DJUSTA BLE LEG A ND CASTOR TOE BOA RD GUA RDRAIL BRAC E PANEL TE LESCOP I C STABI LIS ER... -
Page 5: Know Your Mitower's Components
5 PLATFORM WITH BUILT IN COMPONENT HANGERS To enable one man to erect MI TOWER products, each hatch is fitted with four component hangers which are stowed (two either side) within the platform’s frame. The hangers can be extended when needed and retracted Retract when not. - Page 6 7 ADJUSTABLE LEG AND CASTOR The adjustable leg and castor allows for accurate positioning of your MI TOWER in relation to your workplace. The leg can be Retract extended or retracted to allow for levelling and the brake must be Engagement applied to prevent movement.
-
Page 7: Know Your Kit List And Specifications
3.58 HATCH PLATFORM 8.56 GUARDRAIL BRACE PANEL 3.34 220MM ADJUSTABLE LEG 0.85 125MM LOCKING CASTOR 2.50 TOE BOARD SET 5.33 MITOWER WEIGHT (KG) 109.35 76.45 98.85 PLATFORM SAFE WORKING LOAD 150kg 150kg 150kg 150kg MI TOWER Platform Height Page 5... -
Page 8: Know Your Storage And Transport Pack
TRANSPORT AND STORAGE TROLLEY COMPONENTS For ease of storage and of transportation, GUARDRAIL BRACE PANEL X2 MI TOWER has been designed so that all TOE BOARD SET HATCH PLATFORM components can be safely stored within the ADJUSTABLE LEG AND CASTOR X4 tower’s base assembly. -
Page 9: Safety Dos And Don'ts - Always
SAFETY DOS AND DON’TS - ALWAYS Read and understand this guide before you begin assembly. ALWAYS Ensure that all safety requirements are met and that MI TOWER is the correct access solution for ALWAYS the task you wish to perform. -
Page 10: Safety Dos And Don'ts - Never
Use MI TOWER if you don’t understand something in this guide; please contact the supplier for NEVER advice. Assemble, use, move or dismantle MI TOWER if you are tired or unwell or if you are under the NEVER influence of alcohol or drugs. -
Page 11: Before You Start
MI TOWER is easily dismantled by simply reversing the erection procedure. Make sure that the component hangers are evenly loaded to ensure your MI TOWER remains balanced. You must, however, be protected by guardrail brace panels when standing on any platform and ensure that you use the 3T method when removing guardrail brace panels. -
Page 12: Getting Started
You must only move MI TOWER by manual effort, at a slow pace and only after fully assessing the risk. Once moved, always check MI TOWER before using. If MI TOWER is to be moved to a new location, a new level or over rough terrain, it must be fully dismantled and rebuilt at the new location. -
Page 13: Mitower 2M - Assembly
MI TOWER 2m - ASSEMBLY STEP 1 STEP 2 Fully insert the adjustable Attach a guardrail brace panel to the vertical tube of one frame with the legs with castors into two upper claw positioned above the fourth rung and with all claws facing frames, turning the leg’s height... -
Page 14: Mitower 2M - Assembly
MI TOWER 2m - ASSEMBLY STEP 5 rung, making sure that the wind-lock catches engage. STEP 6 Fit a stabiliser to each corner of the tower. Position the lower horizontal stabiliser coupler clamp just above the frame’s second rung, then secure the top stabiliser coupler clamp just above the a footprint as possible. -
Page 15: Mitower 3M - Assembly
MI TOWER 3m - ASSEMBLY STEP 1 STEP 2 Replicate step 1 from 2m assembly. Attach a guardrail Fit a single 1m frame to a base frame and apply brace panel to the vertical tube of one frame with the the frame clips. -
Page 16: Mitower 3M - Assembly
MI TOWER 3m - ASSEMBLY STEP 4 Construct two sets of conjoined frames, these will give you two 2m sections. Release the frame clips on rung frame. Apply the frame clips and ensure they are correctly locked. Repeat this with the second set. Place... -
Page 17: Mitower 4M - Assembly
MI TOWER 4m - ASSEMBLY STEP 1 REPLICATE STEPS 1 - 6 FROM 2M ASSEMBLY. Place three guardrail brace panels on to one set of hangers and a pair of eight rung conjoined frames to the other side. Enter the tower framework and climb the frame rungs until you are half way through the platform’s trap door. -
Page 18: Mitower 4M - Assembly
MI TOWER 4m - ASSEMBLY STEP 3 sixteenth rung, making sure that the wind-lock catches engage. Extend and lock the four component hangers located on either side of the platform. Transfer the two guardrail brace panels and the set of toe boards to the component hangers on the second platform. -
Page 19: 10 Point Pre-Use Safety Checklist
10 POINT PRE-USE SAFETY CHECKLIST 10 POINT PRE-USE CHECKLIST FOR USERS BEFORE USE Completed tower must be checked by a competent person. COMPONENTS Check all components are free from damage. CASTORS Ensure they are locked. ENVIRONMENT Check your MiTOWER is level. STABILISER COUPLER CLAMPS Check they are secure. -
Page 20: Registrations
REGISTRATIONS Page 19... - Page 21 po p up produc ts . co. uk +4 4 ( 0 )1 2 44 833 933 in fo@ po pup products . co.uk...
Need help?
Do you have a question about the MI TOWER and is the answer not in the manual?
Questions and answers