Hydrajaws M2000 Operating Manual
  1. Manuals
  2. Brands
  3. Hydrajaws Manuals
  4. Test Equipment
  5. M2000
  6. Operating manual

Hydrajaws M2000 Operating Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
M2000 Tester
MAKE SURE IT'S SECURE
OPERATING MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the M2000 and is the answer not in the manual?

Questions and answers

Related Manuals for Hydrajaws M2000

Summary of Contents for Hydrajaws M2000

  • Page 1 M2000 Tester MAKE SURE IT’S SECURE OPERATING MANUAL...

  • Page 2: Table Of Contents

    Adaptor • Use only the genuine Hydrajaws tester when it is given to 19. Bolt Test Adaptor accessories or ancillary equipment other persons. 20. Clevis Adaptor listed in the operating instructions. Note: Not all M2000 kits contain all accessories shown.

  • Page 3: General Testing Procedure

    (fig 3). Bridge Footprint and Tester dimensions 4. Position the tester so that the gauge can be easily read. M2000 Bridge Footprint M2000 Dimensions 5. Adjust the length of the telescopic legs Fig 3 (see section 8) so that all three are in...
  • Page 4 Adjusting the handle position (fig 7) 1. GENERAL TESTING PROCEDURE continued.. The top part of the unit can be rotated if the gauge is becoming obstructed by the unit legs or other objects. TESTING PROCEDURE Fig 4 This is achieved by loosening the three grub screws (a) on the body using the allen key 6.

  • Page 5: Pulling Adaptors

    2.2 M10, M12, M16 AND M20 THREADED STUD ADAPTORS 2. PULLING ADAPTORS Suitable for testing sleeve and stud anchors. 2.1 THE BOLT TEST ADAPTOR Fig 12 (fig 12) After the anchor has been set Fig 9 Using the bolt test adaptor directly in accordance with the manufacturers recommendations, a suitable threaded For M16 nuts, (fig 8) the bolt tester...

  • Page 6: The Clevis Adaptor

    2.4 M5, M6, M8 AND M10 THREADED ROD ADAPTORS 3. SCAFFOLD TESTER KIT The M5 and M6 threaded rod adaptors are Fig 16 The Hydrajaws Test meter is part of a equipped with an external M12 thread for KIT CONTENTS: use in conjunction with the M12 threaded purpose made system for testing fixings and measures the load supplied.
  • Page 7 The new Proof Load testing requirement is for a tensile test of 1.5 x the design load. The Hydrajaws Scaffold Tester Kit will test all of these types to a maximum tensile load of 20kN. TG4:17 also describes six types of anchor most commonly used for anchoring scaffold ties.

  • Page 8: Safety Harness Eyebolt Tester Kit

    Adjust the swivel feet by unscrewing from the telescopic leg, so that each foot is resting on the material around the eyebolt and the bridge is square and level. Fit a protection plate Fig 23 (not supplied by Hydrajaws) between wall and bridge feet if necessary, to protect Reaction loads away Reaction loads away...

  • Page 9: Wall Tie Tester Kit

    The Hydrajaws Wall Tie Tester Kit Mk2 is used for testing all types wall tie under test. of remedial wall tie to meet the requirements of DD140. It is used with appropriate adaptor and mounts direct to tester.

  • Page 10: Material Bond Tester Kit

    KIT CONTENTS: varied range of materials including will increase the likelihood of interfacial failures. • M2000 Medium Duty Tester with concrete, screeds, repair mortars, epoxy 8. Remove excess adhesive from around the edge of the dolly without disturbing its Digital/Analogue gauge to 25kN resin coatings, laminates, plastics, position (fig 26c).

  • Page 11: Optional Load Spreading Bridges

    MATERIAL BOND TESTER KIT continued.. 7. OPTIONAL LOAD SPREADING BRIDGES Hydrajaws offer three optional load IMPORTANT! A low reading will be obtained if: Pyramid Stool spreading bridges, a pyramid stool with • The pull-off tester is misaligned and not perpendicular to the specimen threaded legs and a 270mm or 600mm •...

  • Page 12: Care Of Tester

    9.2 OIL REFILLING INSTRUCTIONS 9. CARE OF TESTER NOTE: A tester with a fixed gauge cannot Fig 32 9.1 LUBRICATION be filled with oil by the operator. Fig 30 1. Remove the bridge and all accessories. Lubrication of rod This is required periodically depending 2.
  • Page 13 FOR MORE INFORMATION ON HYDRAJAWS AND A FULL RANGE OF TESTING APPLICATIONS PLEASE VISIT THE WEBSITE AT: WWW.HYDRAJAWS.CO.UK 20/21 The Courtyard Gorsey Lane Coleshill Birmingham B46 1JA MAKE SURE IT’S SECURE United Kingdom Tel: +44 (0)1675 430 370 Fax: +44 (0)1675 465 950 email: tester@hydrajaws.co.uk...

Table of Contents