Related Manuals for Direct-Lift Pro Cycle XLT
Summary of Contents for Direct-Lift Pro Cycle XLT
- Page 1 Motorcycle Lift 1,000 lbs. capacity Installation, Safety, Operation, Maintenance IN50013 Entire contents © 2011 by Vehicle Service Group. All rights reserved. CO7932 Rev. C 04/20/2011...
- Page 2 Inspection upon receipt of the lift 1. Always inspect the lift for freight damage and make note of any damage on the bill of lading. 2. In case of freight damage, call the truck line immediately and report the damage as a freight claim. Final Set-Up set-up.
- Page 3 M8 x 20 Bolt, Ø10 Lockwasher, Front Wheel Stop M8 Nut Moveable Vise Arm M8 x 20 Bolt Fixed Vise Arm Tie Down Eye Bolt Ø10 Washer M10 Nut Vise Clamp Top of Platform Ø10 Lockwasher Approach Ramp M8 Nut Fig.
- Page 4 The Owner/Employer: the safe use and operation of the lift using the manufacturer’s operating instructions; ALI/SM01-1, ALI Lifting it Right safety manual; ALI/ST-90 ALI Safety Tips card; ANSI/ALI ALOIM-2008, American National Standard for Automotive Lifts-Safety Requirements for Operation, Inspection and Maintenance;...
-
Page 5: Lift Lockout/Tagout Procedure
lift. Lift Lockout/Tagout Procedure Purpose injury to personnel by the operation of lifts in need of repair or being serviced. All employees shall comply with this procedure. Responsibility The responsibility for assuring that this procedure is followed is binding upon all employees and owner/manager. -
Page 6: Restoring Equipment To Service
Sequence of Lockout Procedure 1) Notify all affected employees that a lockout is being performed and the reason for it. provided on the lift. the subject lift. on the device to prevent its unintentional reactivation. An appropriate tag is applied not to operate device or remove tag. - Page 7 Observe and heed SAFETY, CAUTION and WARNING labels on the lift. 1. Lift must be fully lowered and service bay clear of all personnel before the vehicle is brought on lift. 2. Motorcycle Loading: Put motorcycle onto lift. Be sure motorcycle is centered on lift from side to side. Stop when motorcycle front wheel is in wheel clamp/stop.
- Page 8 WARNING If you are not completely familiar with automotive lift maintenance procedures STOP: Contact factory for instructions. lift service personnel to perform maintenance on Lift to be used by trained operator only. Use only genuine replacement parts for repairs. keep all bolts tight. Check periodically.
- Page 10 Item Part Number Description AL-1000G Scissor A-Outside AL-2000G Scissor B-Inside AL-3000 Lift Table-Motorcycle lift (only) AL-4000 Lock Bar AL-5202 Center,Approach Ramp B AL-5400 Vise Clamp Handle-Assy AL-5302 Vise,Moving Jaw-Assy AL-5301 Vise,Stationary Jaw AL-5604 Wheel Stop B10-8×20 Bolt M8×20 B40-8 Lock Washer Ø8...
- Page 11 B30-8 Nut M8 B27-10×20 ‘Tie Down’’ Eye Bolt M10×20 B41-10 Flat Washer Ø10 B30-10 Nut M10 B85-6 Grease Zerk M6 B52-3×30 Cotter Pin Ø3×30 B53-12×45 Pin(B) Ø12×45 AL-4004 Plastic Grip/Safety Release AL-5303 Moveable Vise Extension B41-10 Flat Washer Ø10 AL-6006 Bearing/Cylinder AL-6010 Spacer...
- Page 12 This Page Intentionally Left Blank...
Need help?
Do you have a question about the Pro Cycle XLT and is the answer not in the manual?
Questions and answers